Agilent Technologies Agilent E6474A Manual de usuario

Agilent E6474A Wireless Network

Optimization Platform

Configuration Guide

The purpose of this configuration guide is to assist you in ordering the correct system

configuration for your application.

The Agilent E6474A wireless network optimization platform is used to obtain RF coverage

measurements and service performance measurements for wireless communications

networks. The Windows®based software runs on a PC that interfaces with an Agilent

digital RF receiver and with cdmaOne, cdma2000, HSDPA, UMTS, GSM, GPRS, EDGE,

and iDEN phones. The system can be configured to include receivers and phones from

one or a combination of technologies simultaneously. The system can control up to four

phones.

Recommended minimum

PC specifications: The Agilent E6474A system requires a PC. The PC requirements differ depending on the

hardware configuration and on which parameters are being selected.

Minimum PC specifications:

• XP Professional SP2 (inc XP for Tablet PC)

• 1.6GHz Pentium M 512MB RAM

• Parallel port or USB Port (for software key)

• PCMCIA slot or a USB connection (for multiple hardware support)

• 30 GB hard disk space

• CD-ROM drive recommended for installation

• 1024 x 768 display resolution minimum

Recommended PC specifications:

• XP Professional SP2 (inc XP for Tablet PC)

• Intel® Core™ Duo T2500 (2GHz) 2GB RAM

• Parallel port or USB Port (for software key)

• PCMCIA slot or a USB connection (for multiple hardware support)

• 50 GB hard disk space

• CD-ROM drive recommended for installation

• 1280 x 1024 display resolution minimum

The Agilent network optimization drive test solution can be ordered through part numbers

E6473B, E6474A, W1314A, 86154A, 86156A, and E5643A. These part numbers are

described in this document.

Configuration Process Before using this configuration guide, the following decisions need to be made:

• Which technologies are required?

• Which software measurements are required?

• Which phones and receivers are required?

• Which accessories are required?

This configuration guide is set-out to show the decision process flow you use when

choosing your system.

See Part 1

See Part 2

See Part 3

See Part 4

See Part 5

See Part 6

See Part 7

See Part 8

Part 9 shows some ordering examples.

Support and Training Options

Choose Hardware Accessory Options

Choose Mobile Voice Quality Test

Choose Phone Options

Choose Receiver Options

Choose Post-processing Options

Choose Platform Software Options

Choose Phone and Rx Software Options

START

Part 1: Software Options Select which E6474A software options match your technology and measurement

requirements. Review the upgrade section for additional options.

cdma cdma W-CDMA

License Description One 2000 GSM /UMTS iDEN GPRS

Phone measurements 100 101 200 300 400 600

Receiver measurements 110 111 210 310 410

Receiver and phone

measurements combination 120 121 220 320 420 620

TechTool2phone

measurements 130 131 230

TechTool L2/L3/CAI

Messages 072 073

Table 1- Technology specific software options

Example:

To order receiver and phone measurement combination for cdma2000 technology

systems, select E6474A-121.

SSooffttwwaarreeUUppggrraaddeeOOppttiioonnss

• UMTS receiver software to phone and receiver Combo E6474A-315

• UMTS to HSDPA phone measurement upgrade software license E6474A-325

• UMTS to Motorola Netmon3 measurement upgrade software license3E6474A-340

• GSM/GPRS to UMTS phone measurements E6474A-625

• EDGE phone measurement upgrade E6474A-635

• cdma2000 to 1xEVDO phone measurement (Rev. 0) E6474A-135

• cdma2000 to 1xEVDO phone measurement (Rev. A) E6474A-137

• cdma2000 to 1xEVDO receiver measurement E6474A-136

• iDEN to WiDEN phone measurements E6474A-435

PPhhoonneeSSccaannnniinngg

• Sagem BCCH scanning measurement software license E6474A-201

NNootteess

11. HSDPA and EDGE measurements are enabled through their respective upgrade

licenses.

22. TechTool enables low-end measurement capability at a lower price. For example,

E6474A-130 and E6474A-070 will provide CDMA phone measurement view and logging

only. TechTool is not available for all technologies.

33. Netmon3 includes support for Motorola E1000 phone.

Each software order includes the following components:

• CD with software and documentation (training and reference)

• User’s Guide (E6474-90052) and Getting Started Guide (E6474-90085)

• USB license key (initialized with licenses)

Part 2: Platform Software Options Select which E6474A platform software option matches your system needs.

License Description Option Number

Initialized parallel license key10051

Multiple phone license 010

Indoor mapping license 030

MapX Mapping software license 0402

Client data measurement software license 700

Server data measurement software license27103

Wireless Application Measurement Software 740

Video Streaming 741

Video Telephony 742

Video Streaming plus non-reference video MoS 744

WAMS Lite47454

TechTool data logging and GPS 070

TechTool alarming capabilities 071

Platform software CD only 090

Table 2 - Platform software options

11The E6474A licenses are only delivered on a USB key. A parallel key must be ordered separately if required.

Refer to the Software License section below for information on the Keyless License features.

22MapX is required for release 10.0 onwards to support mapping features. Release 9.x and earlier did not require

this option.

33E6474A-710 is a “server” application, used with E6474A-700, and requires to be run on a separate PC platform

from the optimization software. E6474A-710 is provided with a CD containing software and documentation, a

Server Installation Guide and a Parallel port software license key. Refer to the Wireless Data Measurements

data sheet for further details (literature number 5988-1507EN).

44WAMS Lite is available as a low cost entry point to basic service testing. Tests included are FTP test, PING, voice

connectivity, video connectivity, AT commands, and DOS commands only.

KKeeyylleessssSSooffttwwaarreeLLiicceennssiinngg

Server-based keyless software licensing is offered as an alternative to the default

hardware key-based licensing. Software licensing provides the ability to maintain a pool

of E6474A measurement licenses on a server and then distributes those licenses to client

drive-test PCs using a check-out process. Typically only one server application is required

per customer. This licensing option is aimed at customers managing more than twenty

E6474A systems.

License Description Option Number

Software licensing server application E6474A-081

Software licensing option delivery E6474A-080

Hardware key to software license exchange E6474A-083

Table 2a - Software license options

NNoottee: The minimum license check-out period is seven days. Techtool options are not

available under the software licensing system. An E6474A-083 purchase is required for

every E6474A measurement license to be transferred.

Part 3: Post-Processing Options Select which post-processing software you require.

License Description Option Number

Analysis Reporter E6474A-758

Example:

To add Analysis Reporter capability to your system select E6474A-758.

RReeffeerrrraallSSttaatteemmeennttffoorrAAccttiixxUUsseerrss

Agilent maintains strong links with Actix, who supply post-processing software. However

Agilent no longer re-sells this software. For more information on purchasing options and

support of Actix software, please contact Actix directly ([email protected]).

Part 4: Receiver Options Agilent’s new multi-technology and multi-band receivers support up to four RF bands in a

single compact package. The combination of uplink and downlink bands depends on the

configuration chosen. All receivers include a integral 12 channel GPS and four-port USB

hub. The receivers are listed by option number and by technology with supported bands.

Receivers are all options of the base product W1314A.

Option Number Description

W1314A-100 GSM 900/1800 (UL/DL)

W1314A-110 GSM/CDMA/UMTS 850/1900 (UL/DL)

W1314A-120 GSM450/CDMA450(partial)(UL/DL), GSM 900/1800 (DL) and UMTS 2100 (DL)

W1314A-130 GSM/CDMA/UMTS 850/1900 (DL) and GSM 900/1800 (DL)

W1314A-140 GSM/CDMA/UMTS 850 (DL), GSM 900/1800 (DL) and UMTS 2100 (DL)

W1314A-150 GSM/CDMA/UMTS 850/1900 (DL), UMTS 1700 (UL), CDMA/UMTS 2100 (DL)

W1314A-200 UMTS 2100 (UL/DL) GSM 900/1800 (DL)

W1314A-210 UMTS 2100 (DL), UMTS TDD 2100 (TDD) and GSM 900/1800 (DL) (TDD future

enhancement)

W1314A-220 CDMA/UMTS 1900/2100 (DL), UMTS TDD 2100 (TDD) and CDMA 850 (DL)

(TDD future enhancement)

W1314A-230 CDMA/UMTS 850/2100 (UL/DL)

W1314A-300 iDEN 800/900 (UL/DL)

W1314A-310 iDEN 800/900 (DL), GSM/CDMA/UMTS 850/1900 (DL)

W1314A-410 JCDMA 800 (DL), JCDMA/UMTS 1700 (DL) and UMTS 2100 (DL)

W1314A-500 WiLAN (TDD), GSM 900/1800 (DL) and UMTS 2100 (DL) (WiLAN is CW only at

present)

Table 4a - Digital Receiver Part Numbers - listed by part number.

EExxaammppllee

W1314A-200 supports UMTS at 2100 MHz in both the uplink and downlink bands as

well as GSM 900 and GSM 1800 in the downlink bands only.

NNootteess

Agilent receivers require related receiver measurement software as described in the Software

Options section (refer to Table 1).

Agilent receivers include an internal 12 channel GPS receiver although you can use an alternative

external GPS unit if preferred.

If you require dead reckoning with your GPS, you need to use an external GPS. Agilent offers an

external GPS with dead reckoning capability (refer to Table 6)

You need to select the receiver that covers the frequency bands in which you want to make

measurements.

Each receiver includes the following components:

• Magnetic-mount RF antenna for the corresponding frequency band

• Adaptor for RF antenna connection to receiver

• USB cable for connection to PC

• AC/DC power supply

• DC power cord - cigarette lighter type

• Mounting kit - mounting plate and screws for mounting receiver in a vehicle

Part 5: Phone Options Select which phone type you require for your system from the E6473B parts below.

Alternatively source a supported phone directly from a third party; please refer to the

agilent.com website or contact your Agilent representative for a list of supported phones.

Phone Descriptions (test mobile) Option Number

Sagem GSM 900/1800/1900 E6473B-720

Sagem GPRS/GSM 900/1800/1900 E6473B-740

Nokia N80 GSM/GPRS/EDGE (850/900/1800/1900) UMTS (2.1 GHz) E6473B-758

Nokia 6125 GSM/GPRS/EDGE (850/900/1800/1900) E6473B-753

Kyocera 3035 phone kit (US and China) E6473B-770

Table 5 - Engineering phone product options

Note: For the current supplied phone models please contact your Agilent representative.

Example:

To order a Sagem GSM 900/1800/1900 test mobile select E6473B-720

Note: These options include the manufacturers direct connect cables.

Phones are supplied with the manufacturers one year warranty. Agilent do not offer

extended warranty on phones.

Part 6: Mobile Voice Quality Testing Options

For up to date information on Agilent’s voice quality test solutions, please contact your

Agilent sales representative.

SSeerrvveerr//OOffffiicceeppaarrttoofftthheessyysstteemm

Descriptions Option Number

Voice Responder Unit J5426AZ

Voice Quality Test Software (Office Side) B9990A-100

Table 6 - Server/Office option requirements

CClliieenntt//MMoobbiilleeVVaannppaarrttoofftthheessyysstteemm

Descriptions Option Number

Single Phone Mobile VQT Client Software B9990A-200

Multi-Phone Mobile VQT Client Upgrade License B9990A-300

Cable - Nokia POP-Port Mobiles E6473B-882

Cable - 2.5mm Ear/Microphone Jack Supported Mobiles E6473B-883

Table 7 - Client/Mobile Van option requirements

Part 7: Hardware Accessory Options Select which hardware accessories you need with your system.

Drive-test System Accessories

Direct Connect GPS DR w/Mag Mount Antenna -

External GPS device with dead reckoning that can

connect to either the Agilent direct connect hub or

directly to the laptop via serial port. This option

includes a magnetic mount GPS antenna. E6473B-030

Direct Connect GPS DR w/Perm Mount Antenna -

This option is the same as E6473B-030 but with

a permanent mount GPS antenna. E6473B-031

Antenna kits

900/1800 MHz Phone Antenna Kit E6473B 898

800/1900 MHz Phone Antenna Kit E6473B 899

Receiver Antenna,Perm. Mt 800/1900MHz 86156A-700

Receiver Antenna, Perm. Mt 900/1800MHz 86156A-701

Receiver PCS antenna, magnetic mount 86154A-410

Receiver Cellular antenna, magnetic mount 86154A-430

Miscellaneous options

4-port USB to serial hub 86154A-036

Briefcase for phone/receiver + phone 86154A-531

Table 6 - Accessories

Part 8: Support and Training Options The E6474A software licenses include the following product support options for the first

year:

• Agilent Call Center phone support, four hour response time or less.

• Software updates.

The Agilent Advantage Integrated Customer Care Program allows customers to upgrade

to more comprehensive product support options. For the program summary and options,

refer to publication 5988-4793EN.

On-site training is orderable for E6474A and for WAMS. This provides:

• Telephone assistance and Web training on specific topics

• On-site training and start-up assistance

Order as:

E6474A One day on-site training - H7211B-209.

WAMS One day on-site training - H7211B-232.

E6474A and WAMS Two day on-site training - H7211B-233.

Mobile Voice Quality Test One day on-site training - H7211B-235.

On-site training is not available in all locations. Please contact your Agilent sales

representative for further information. It is highly recommended that new E6474A users

order training options.

Part 9: Ordering examples These examples are not a complete list of all possible configurations, they show typical

configurations to illustrate the ordering process.

CDMA ordering examples

You want a cdmaOne phone-based measurement system (single phone). You will provide

your own GPS, laptop and phone.

You need to order Quantity

E6474A: Wireless network optimization platform

E6474A-100: cdmaOne phone measurement software license 1

E6474A-040: MapX mapping software license 1

You want a cdmaOne combination phone and receiver-based measurement system for the

PCS band. You need one receiver and multi-phone option. In-vehicle use intended. You

provide your own Laptop PC, and phones with OEM cables.

You need to order Quantity

E6474A: Wireless network optimization platform

E6474A-120: Combined cdmaOne phone- and receiver measurement

software license 1

E6474A-010: Multiple phone software license 1

E6474A-040: MapX mapping software license 1

W1314A: Agilent receiver hardware

W1314A-110 GSM/CDMA/UMTS 850/1900 (UL/DL) 1

Otros manuales para Agilent E6474A

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies LogicWave Manual de usuario

Agilent Technologies

Agilent Technologies L4400 Series Manual de usuario

Agilent Technologies

Agilent Technologies E4419B Manual de usuario

Agilent Technologies

Agilent Technologies 16517A Manual de servicio

Agilent Technologies

Agilent Technologies N9340B Manual

Agilent Technologies

Agilent Technologies 16753A Manual de usuario

Agilent Technologies

Agilent Technologies OmniBER 718 SDH Manual de usuario

Agilent Technologies

Agilent Technologies 8753ES Manual de usuario

Agilent Technologies

Agilent Technologies TS-5410 Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies Cary 8454 Manual de usuario

Agilent Technologies

Agilent Technologies varian 310-MS LC/MS Manual de usuario

Agilent Technologies

Agilent Technologies K6460 Manual de instalación y funcionamiento

Agilent Technologies

Agilent Technologies 4100 Manual de usuario

Agilent Technologies

Agilent Technologies E5900B Manual de usuario

Agilent Technologies

Agilent Technologies U1731C Manual de usuario

Agilent Technologies

Agilent Technologies DSOX4USBSQ USB 2.0 Manual de usuario

Agilent Technologies

Agilent Technologies 16800 Series Hoja de datos

Agilent Technologies

Agilent Technologies U2722A Manual de usuario

Agilent Technologies

Agilent Technologies N5502A Manual de usuario

Agilent Technologies

Agilent Technologies X Series Manual de usuario

Agilent Technologies

Agilent Technologies 16441A R-Box Manual de usuario

Agilent Technologies

Agilent Technologies 16700 SERIES LOGIC ANALYSIS SYSTEM 16700 Instrucciones de funcionamiento y seguridad

Agilent Technologies

Agilent Technologies 2100 Bioanalyzer System Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies VS Series Guía de referencia

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario