Agilent Technologies N5502A Manual de usuario

The test & measurement

equipment you need at

the price you want.

Alltest carries the world’s largest selection of

used/refurbished benchtop test & measurement

equipment at 50% the price of new.

Our equipment is guaranteed working, warrantied, and

available with certified calibration from our in-house staff

of technicians and engineers.

• 10+ full time technicians with over 150 years of

specialization

• 90 day warranty & 5 day right of return on all

equipment

•

• 1-3 year warranties for new and

premium-refurbished equipment

• Every unit tested to OEM specifications

• Satisfaction guaranteed

You have plans, we will help you achieve them.

Any project. Any budget.

Get a quote today!

CCall (732) 919-3339 or email sales@alltest.net.

Alltest Instruments, Inc.

500 Central Ave.

Farmingdale, NJ 07727

P: (732) 919-3339

F: (732) 919-3332

alltest.net

sales@alltest.net

Agilent Technologies

Agilent E5505A

Phase Noise

Measurement System

Installation Guide

Fifth Edition, December 2009

Create a Recovery DVD

Refer to Chapter 5, Recovery

Notices

No part of this manual may be reproduced

in any form or by any means (including

electronic storage and retrieval or transla-

tion into a foreign language) without prior

agreement and written consent from Agi-

lent Technologies, Inc. as governed by

United States and international copyright

laws.

Manual Part Number

E5505-90001

Edition

Fifth Edition, December 2009

Printed in USA

Agilent Technologies, Inc.

1400 Fountaingrove Pkwy

Santa Rosa, CA 95403

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

ject to being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequential damages in connection

with the furnishing, use, or perfor-

mance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering the material in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

The hardware and/or software described in

this document are furnished under a

license and may be used or copied only in

accordance with the terms of such license.

Restricted Rights Legend

If software is for use in the performance of

a U.S. Government prime contract or sub-

contract, Software is delivered and

licensed as “Commercial computer soft-

ware” as defined in DFAR 252.227-7014

(June 1995), or as a “commercial item” as

defined in FAR 2.101(a) or as “Restricted

computer software” as defined in FAR

52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use,

duplication or disclosure of Software is

subject to Agilent Technologies’ standard

commercial license terms, and non-DOD

Departments and Agencies of the U.S. Gov-

ernment will receive no greater than

Restricted Rights as defined in FAR

52.227-19(c)(1-2) (June 1987). U.S. Govern-

ment users will receive no greater than

Limited Rights as defined in FAR 52.227-14

(June 1987) or DFAR 252.227-7015 (b)(2)

(November 1995), as applicable in any

technical data.

Safety Notices

CAUTION

A CAUTION notice denotes a haz-

ard. It calls attention to an operat-

ing procedure, practice, or the like

that, if not correctly performed or

adhered to, could result in damage

to the product or loss of important

data. Do not proceed beyond a

CAUTION notice until the indicated

conditions are fully understood and

met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly per-

formed or adhered to, could result

in personal injury or death. Do not

proceed beyond a WARNING

notice until the indicated condi-

tions are fully understood and met.

Microsoft ® is a U.S. registered trademark

of Microsoft Corporation.

Windows ® and MS Windows ®

are U.S. registered trademarks of

Microsoft Corporation.

Pentium ® is a U.S. registered trademark of

Intel Corporation.

Adobe ® Acrobat ® Adobe, the Adobe

Logo, Acrobat and the Acrobat Logo are

trademarks of Adobe Systems Incorpo-

rated.

Symantec Ghost®is a U.S. registered

trademark of Symantec Corporation

E5505A Installation Guide 3

Contents

1 General Information

Introduction 8

Table 1. E5505A installation reading road map 8

Unpacking and Inspecting the System 9

To unpack a racked system 9

To unpack a benchtop system 10

Inspecting the system 10

Table 2. E5505A connectors and adapters 11

System Overview 12

Figure 1. Agilent E5505A benchtop system, typical configuration 13

Table 3. Equivalent system/instrument model numbers 13

System Specifications 14

Table 4. Mechanical and environmental specifications 14

Table 5. Operating characteristics 14

Table 6. Amplitude ranges 15

Power requirements 15

Table 7. E5505A maximum AC power requirements 15

Documentation 17

Figure 2. Navigate to system documentation 17

2 Flat-Panel Display

Connecting a Rack-Mounted Flat-Panel Display 20

Table 8. Monitor, keyboard, and mouse parts listing 20

Figure 3. Display assembly installation 21

3 System Interconnections

Making Connections 24

Figure 4. Connect adapter to back of PC digitizer card 24

System Connectors 25

Table 9. E5505A connectors and adapters 25

System Cables 26

Table 10. E5505A cables and connections 26

Figure 5. System connections with test set, standard model 27

Figure 6. System connections with test set, option 001 28

Figure 7. System connections with test set, option 201 29

4E5505A Installation Guide

4 Measurement Software

Powering the System On 32

To power on a racked system 32

To power on a benchtop system 32

Starting the Measurement Software 33

Figure 8. Log-In Window 33

Figure 9. E5500 UI and Shutdown desktop shortcuts 33

Figure 10. Navigate to E5500 user interface from start menu 34

Figure 11. Main E5500 user interface window 35

Specifying Assets for the Confidence Test 36

Figure 12. Navigate to server hardware connections 36

Figure 13. Successful I/O check 37

Figure 14. Failed I/O check 37

Figure 15. Select test set, FFT analyzer, and swept analyzer 38

Running the Software Confidence Test 39

Figure 16. Opening the parameters definition file 39

Table 11. Parameter Data for the Agilent N5500A Confidence Test Example 40

Beginning the Measurement 41

Figure 17. Selecting a new measurement 41

Figure 18. Selecting a new measurement 41

Figure 19. 50 W connector location for measurement 42

Making the Measurement 42

Figure 20. Typical phase noise curve for a system confidence test 43

Congratulations 43

Additional Assets 44

Configuring an Asset 44

Figure 21. Navigate to Asset Manager 44

Figure 22. Navigate to Add in Asset Manager 45

Figure 23. Select source as asset type 45

Figure 24. Choose source 46

Figure 25. Select I/O library 47

Figure 26. Enter asset and serial number 47

Figure 27. Enter comment 48

Figure 28. Click Check button 48

Figure 29. Confirmation message 49

Verifying Server Hardware Connections 50

Figure 30. Navigate to server hardware connections 50

Figure 31. Select Sources tab 50

Figure 32. Successful I/O check 51

E5505A Installation Guide 5

Figure 33. Failed I/O check 51

Setting GPIB Addresses 53

Table 12. Default GPIB addresses 53

Figure 34. Asset Manager on System menu 54

Figure 35. Asset Manager window 54

Figure 36. GPIB address dialog box 55

Powering the System Off 56

To power off a racked system 56

To power off a benchtop system 56

Using the E5500 Shutdown Utility 56

Figure 37. Shutdown utility icon 56

5 Recovery

Hard Drive Recovery Process - Advantech PC 58

Create an Image on the Recovery DVD 58

Recover From a System Crash Using the Recovery Partition 61

Re-image a New Hard Drive Using the Recovery DVD 62

Partition a New Hard Drive Using Windows Disk Manager® 63

Create an Image on the New Recovery Partition 64

System Boot Order Check 65

Hard Drive Recovery Process - Kontron PC 66

Configuring recovery prompt timing 68

Hard Drive Disk Replacement Procedure 68

Figure 38. Hard Disk Drive Assembly 69

Figure 39. Ejector Lever Pulled Up 70

Figure 40. Ejector Lever Pushed Down 70

6 Preventive Maintenance

Using, Inspecting, and Cleaning RF Connectors 72

Repeatability 72

RF Cable and Connector Care 72

Proper Connector Torque 73

Table 13. Proper Connector Torque 73

Connector Wear and Damage 73

SMA Connector Precautions 74

Cleaning Procedure 74

6E5505A Installation Guide

Table 14. Cleaning Supplies Available from Agilent 75

General Procedures and Techniques 76

Figure 41. GPIB, 3.5 mm, Type-N, power sensor, and BNC connectors 76

Connector Removal 77

Instrument Removal 79

Standard instrument 79

Half-Rack-Width Instrument 80

Figure 42. Instrument lock links, front and rear 81

Benchtop Instrument 81

Instrument Installation 82

Standard rack instrument 82

Half-Rack-Width instrument 83

Benchtop instrument 83

A Service, Support, and Safety Information

Safety and Regulatory Information 86

Safety summary 86

Equipment Installation 86

Environmental conditions 87

Before applying power 87

Ground the instrument or system 88

Fuses and Circuit Breakers 88

Maintenance 89

Safety symbols and instrument markings 89

Table 15. Safety symbols and instrument markings 89

Declaration of Conformity 91

Compliance with German noise requirements 91

Table 16. German noise requirements summary 91

Compliance with Canadian EMC requirements 91

Service and Support 92

Service and Support Options 92

Contacting Agilent 92

Shipping Your Analyzer to Agilent for Service or Repair 93

Return Procedure 94

Determining your instrument’s serial number 94

Figure 43. Serial number location 94

Shipping the instrument 95

Agilent E5505A Phase Noise Measurement System

Installation Guide

Agilent Technologies

General Information

Introduction 8

Unpacking and Inspecting the System 9

System Overview 12

System Specifications 14

Documentation 17

This chapter introduces you to the Agilent E5505A Phase Noise

Measurement System. It contains an overview of the system, system

specifications, and guidelines for unpacking a system. It also provides a

reading road map for installation documentation.

8E5505A Installation Guide

1General Information

Introduction

Use this guide to unpack, connect instruments (if needed), power on,

configure, test, and power off your Agilent E5505A Phase Noise

Measurement System. For all system models, start with the information in

this chapter—especially the unpacking guidelines starting on page 10.

If you’ve ordered a racked system, it arrives as a turnkey solution—ready

to power on with all hardware and software installed. If you’ve ordered a

flat- panel display, procedures for mounting it are in Chapter 2. Follow the

powering on procedures in Chapter 4 and you’re ready to make your first

measurement.

A benchtop system arrives with all hardware and software installed, but

you must connect the instruments with the appropriate cables. You’ll find

instrument connection diagrams in Chapter 3. (Agilent ships the needed

cables with the system.) Then proceed to Chapter 4 to power on your

system and make your first measurement.

Use Table 1 as a guide to the chapters to use for your model:

•Racked system

•Benchtop system

NOTE

If you need to re-install the phase noise hardware and software in the E5505A system PC

for any reason, refer to the E5505A Phase Noise Measurement System User’s Guide for

information and procedures.

Table 1 E5505A installation reading road map

Rack Benchtop

Chapter 1, “General Information” Chapter 1, “General Information”

Chapter 2, “Flat-Panel Display” (if applicable) Chapter 3, “System Interconnections”

Chapter 4, “Measurement Software” Chapter 4, “Measurement Software”

Appendix A, “Service, Support, and Safety

Information”

Appendix A, “Service, Support, and Safety

Information”

General Information 1

E5505A Installation Guide 9

Unpacking and Inspecting the System

This section presents procedures for unpacking a racked system and a

benchtop model. Do not attempt to unpack your system without reviewing

them.

To unpack a racked system

To unpack an E5505A racked system, you need the following tools:

•Safety glasses

•Klimp hammer or prybar to remove the klimps

•Socket wrench and sockets

•Pliers

To remove the racked system from the packing crate, follow these steps:

1Remove the klimps from the crate wall marked “Ramp Panel.”

2Position the ramp panel to create a ramp. The non- hinged end rests on

the crate base and the hinged flap meets the floor.

3Secure the ramp panel to the base by placing the drop- in bolt (located

in the packing foam) through the holes in the ramp and the base of the

crate.

4Remove the remaining crate walls and top, as well as the foam padding

from the top of the cabinet and the anti- static bag covering the cabinet.

5Remove the center restraining bolts and cleats holding the cabinet to

the crate base using the socket wrench. These bolts are located on the

ramp side of the crate and the side opposite.

6Lift the side bolts from the curb gate on the ramp side of the crate base

using pliers. Remove the curb gate.

7With one person behind the system and two guiding the sides, gently

roll the system down the ramp.

NOTE

Retain all packing material—crate, foam, curb gate, bolts, cleats, and klimps—for future

use should you need to move the system to another location.

WARNING

Always wear safety glasses or goggles when removing steel clips (klimps) from

the shipping crate. These clips are under tension and when pried free can spring

back and cause injury to unprotected eyes.

Tabla de contenidos

Otros manuales de Instrumento de medición de Agilent Technologies

Agilent Technologies

Agilent Technologies N8262A P Series Manual de usuario

Agilent Technologies

Agilent Technologies E3238S Instrucciones de funcionamiento y mantenimiento

Agilent Technologies

Agilent Technologies E4418B Manual de usuario

Agilent Technologies

Agilent Technologies 5062-8218 Manual de instalación y operación

Agilent Technologies

Agilent Technologies FieldFox N9923A Manual de usuario

Agilent Technologies

Agilent Technologies K6460 Manual de instalación y funcionamiento

Agilent Technologies

Agilent Technologies 4155B Manual de usuario

Agilent Technologies

Agilent Technologies ESA-E Series Manual

Agilent Technologies

Agilent Technologies 4155C Manual de usuario

Agilent Technologies

Agilent Technologies U1401B Manual de usuario

Agilent Technologies

Agilent Technologies 4294A Manual del propietario

Agilent Technologies

Agilent Technologies FieldFox N9912A Guía de inicio rápido

Agilent Technologies

Agilent Technologies EMC Series Manual de usuario

Agilent Technologies

Agilent Technologies B1500A Manual de usuario

Agilent Technologies

Agilent Technologies 2100 Bioanalyzer System Manual de instalación y funcionamiento

Agilent Technologies

Agilent Technologies 8510C Manual del propietario

Agilent Technologies

Agilent Technologies J2300D Manual de lista de piezas

Agilent Technologies

Agilent Technologies E8363BU-014 Manual de instalación y operación

Agilent Technologies

Agilent Technologies 85024A Manual

Agilent Technologies

Agilent Technologies 71612 Manual de usuario

Agilent Technologies

Agilent Technologies InfiniiVision 6000 Series Manual de usuario

Agilent Technologies

Agilent Technologies Acqiris U10 Series Manual de usuario

Agilent Technologies

Agilent Technologies Agilent 4396B Manual de usuario

Agilent Technologies

Agilent Technologies Seahorse XFe96 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario