Agilent Technologies 100 Manual de usuario

100 Automated Disintegration Apparatus

Operator’s Manual

Notices

Manual Part Number

70-9066 Rev E

February 2020

No part of this manual may be

reproduced in any form or by any means

(including electronic storage and retrieval

or translation into a foreign language)

without prior agreement and written

consent from Agilent Technologies, Inc.

as governed by United States and

international copyright laws.

Agilent Technologies, Inc.

3501 Stevens Creek Blvd.

Santa Clara, CA 95052 USA

Warranty

The material contained in this document

is provided “as is,” and is subject to being

changed, without notice, in future

editions. Further, to the maximum extent

permitted by applicable law, Agilent

disclaims all warranties, either express or

implied, with regard to this manual and

any information contained herein,

including but not limited to the implied

warranties of merchantability and fitness

for a particular purpose. Agilent shall not

be liable for errors or for incidental or

consequential damages in connection

with the furnishing, use, or performance

of this document or of any information

contained herein. Should Agilent and the

user have a separate written agreement

with warranty terms covering the

material in this document that conflict

with these terms, the warranty terms in

the separate agreement shall control.

Technology Licenses

The hardware and/or software described

in this document are furnished under a

license and may be used or copied only in

accordance with the terms of such

license.

Restricted Rights Legend

U.S. Government Restricted Rights.

Software and technical data rights

granted to the federal government

include only those rights customarily

provided to end user customers. Agilent

provides this customary commercial

license in Software and technical data

pursuant to FAR 12.211 (Technical Data)

and 12.212 (Computer Software) and, for

the Department of Defense, DFARS

252.227-7015 (Technical Data -

Commercial Items) and DFARS

227.7202-3 (Rights in Commercial

Computer Software or Computer

Software Documentation).

Safety Notices

CAUTION

A CAUTION notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in damage to the product or

loss of important data. Do not

proceed beyond a CAUTION

notice until the indicated

conditions are fully understood

and met.

WARNING

A WARNING notice denotes a

hazard. It calls attention to an

operating procedure, practice, or

the like that, if not correctly

performed or adhered to, could

result in personal injury or death.

Do not proceed beyond a

WARNING notice until the

indicated conditions are fully

understood and met.

100 Operator’s Manual 3

Content

1Safety 7

Electrical Hazards 9

Warning 10

Caution 10

Note 10

Information Symbols 11

2 Introduction 13

Conventions Used in this Manual 15

Serial Number Format 15

3 Setting Up the 100 17

Unpacking Your 100 18

Environmental Requirements for Installation 19

Setting up the Water Bath 20

Initial Power Up 21

Electrical Connections 21

Content

4100 Operator’s Manual

Installing the Temperature Probe 23

Water Bath Status LEDs 24

Setting the Date / Time Clock 25

Mounting Baskets and Filling Beakers 26

Draining the Water Bath 26

Hidden Key Functions 27

4 Operating the 100 29

Setting Water Bath Temperature 30

Setting Print Frequency for the Report Center Printer 30

Adjusting Basket Height 31

Placing Dosage Units in the Baskets 32

Selecting Operating Mode 32

Single-basket Operation 32

Multi-basket Operation 33

Three-Basket Operation 36

Printer Operation During Manual or Program Operation (Optional) 36

5 Troubleshooting and Maintenance 37

Preventive Maintenance 38

Weekly Maintenance 38

Monthly Maintenance 38

Every Six Months Maintenance 39

Yearly Maintenance 39

Disintegration Basket Care 40

Water Bath / Acrylic Care 41

Visual Checks 42

Water Bath Temperature Probe Accuracy Test 43

Report Center Impact Printer 45

Installing the Cartridge Ribbon 45

Content

100 Operator’s Manual 5

Replacing the Paper Roll 46

Toggling Your Printer Online 47

Printer Self Test 48

Printer Configuration 49

Troubleshooting 51

Obtaining Warranty and Other Services 52

Content

6100 Operator’s Manual

This page was intentionally left blank, except for this message.

100 Operator’s Manual 7

1Safety

Electrical Hazards 9

1Safety

8100 Operator’s Manual

The Agilent 100 has been designed and tested so that when used properly you

have an accurate, fast, flexible, and safe instrument.

If the equipment is used in a manner not specified by the manufacturer, the

protection provided by the equipment may be impaired.

The Agilent 100 is operated in conjunction with equipment that uses aqueous

liquids. Unskilled, improper, or careless use of this instrument can create shock

hazards, fire hazards, or other hazards which can cause death, serious injury to

personnel, or severe damage to equipment and property.

Information on safety practices is provided with your instrument and operation

manuals. Before using your instrument or accessories, you must thoroughly read

these safety practices.

Observe all relevant safety practices at all times.

1Safety

100 Operator’s Manual 9

Electrical Hazards

The Agilent 100 contains electrical circuits, devices, and components operating

at dangerous voltages. Contact with these circuits, devices, and components can

cause death, serious injury, or painful electric shock.

Panels or covers that are retained by fasteners which require the use of a tool for

removal may be opened only by Agilent-trained, Agilent-qualified, or

Agilent-authorized service engineers. Consult the manuals or product labels

supplied with the 100 to determine which parts are operator-accessible.

Application of the wrong supply voltage, connection of the instrument to an

incorrectly wired supply outlet, or lack of proper electrical grounding can create a

fire hazard or a potentially serious shock hazard and could seriously damage the

instrument and any attached ancillary equipment.

Always use a three-wire outlet with ground connection which is adequately rated

for the load. The installation must comply with local, state, and federal safety

regulations.

Do not connect the instrument to the main power supply until you have made

sure that the operating voltage is correctly set for the main power supply in the

specific outlet in your laboratory to which the equipment will be connected.

1Safety

10 100 Operator’s Manual

Warning

WARNING

A ‘Warning’ message appears in the manual when failure to observe instructions

or precautions could result in death or injury.

Read all warnings and cautions carefully and observe them at all times.

Caution

CAUTION

A ‘Caution’ message appears in the manual when failure to observe instructions

could result in damage to equipment (Agilent supplied and / or other associated

equipment).

Note

NOTE

A ‘Note’ appears in the manual to give advice or information.

Otros manuales para 100

Tabla de contenidos

Otros manuales de Equipo de laboratorio de Agilent Technologies

Agilent Technologies

Agilent Technologies 5DX Manual de usuario

Agilent Technologies

Agilent Technologies 6850 Series Instrucciones de funcionamiento e instalación

Agilent Technologies

Agilent Technologies XY Manual de usuario

Agilent Technologies

Agilent Technologies 5110 ICP-OES Manual de usuario

Agilent Technologies

Agilent Technologies 1260 Infinity Manual de usuario

Agilent Technologies

Agilent Technologies Magnis G9710A Manual de usuario

Agilent Technologies

Agilent Technologies G1992A Manual de usuario

Agilent Technologies

Agilent Technologies 8860 Manual de usuario

Agilent Technologies

Agilent Technologies 33120A Manual de usuario

Agilent Technologies

Agilent Technologies 1290 Infinity II Manual de usuario

Agilent Technologies

Agilent Technologies 1290 infinity Manual de usuario

Agilent Technologies

Agilent Technologies E7473A Manual de usuario

Agilent Technologies

Agilent Technologies 5100 ICP-OES Instrucciones de funcionamiento

Agilent Technologies

Agilent Technologies G1701DA Manual de usuario

Agilent Technologies

Agilent Technologies 7673 Manual de usuario

Agilent Technologies

Agilent Technologies 6890 Series Manual de usuario

Agilent Technologies

Agilent Technologies OmnoBER 725 Manual de usuario

Agilent Technologies

Agilent Technologies Varian 325-MS LC/MS Manual de usuario

Agilent Technologies

Agilent Technologies ZORBAX Series Manual de usuario

Agilent Technologies

Agilent Technologies 5975T LTM GC/MSD Manual de funcionamiento

Agilent Technologies

Agilent Technologies G1329A Manual de usuario

Agilent Technologies

Agilent Technologies 1290 infinity Manual de usuario

Agilent Technologies

Agilent Technologies Labware MiniHub Manual de usuario

Agilent Technologies

Agilent Technologies 1220 Infinity II LC Manual de instalación y operación

Manuales populares de Equipo de laboratorio de otras marcas

Qiagen

Qiagen DML 3000 Manual de usuario

Queensgate

Queensgate NANOSCAN OP400 Manual de programación

Conviron

Conviron GEN1000-GE Manual de usuario

Parr Instrument

Parr Instrument 4560 Manual de instrucciones

IKA

IKA IC control Manual de usuario

Integra

Integra DOSE IT Manual de usuario

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manual de usuario

NI PXI-5422 Manual

Collomix

Collomix Aqix Manual de usuario

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manual de usuario

Ocean Insight

Ocean Insight FLAME-NIR+ Manual de usuario

Parker

Parker ALIGN-MG-NA Manual de usuario

BD 644787 Manual de usuario

DENTAURUM

DENTAURUM Compact Megaplus Manual de usuario

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manual de usuario

VWR

VWR SAS Super IAQ Manual de usuario

illumina

illumina MiSeqDx Manual de usuario

Yamato

Yamato BM510 Manual de usuario