Agilent Technologies 1290 infinity Manual de usuario
111
1290 Infinity TCC User Manual
Agilent Technologies
8
Maintenance
Introduction to Maintenance and Repair 112
Cautions and Warnings 113
Overview of Maintenance 115
Cleaning the Column Compartment 116
Changing Column Identification Tags 117
Adding Heater Devices 119
Installing the capillaries 124
Correcting Leaks 131
Replacing Head Parts of Column Switching Valve 133
Replacing Valve Heads 136
Preparing the Column Compartment for Transportation 140
Replacing the Module Firmware 143
This chapter describes the maintenance tasks for the TCC. If the instrument
needs repair please contact your Agilent service representative.
112 1290 Infinity TCC User Manual
8Maintenance
Introduction to Maintenance and Repair
Introduction to Maintenance and Repair
The module is designed for easy maintenance. The most frequent
maintenances such as maintaining valve heads (if optional valve drive is
installed) or replacing low dispersion heat exchangers can be done from the
front with module in place in the system stack.
NOTE
There are no serviceable parts inside.
Do not open the module.
1290 Infinity TCC User Manual 113
Maintenance 8
Cautions and Warnings
Cautions and Warnings
WARNING
Toxic, flammable and hazardous solvents, samples and reagents
The handling of solvents, samples and reagents can hold health and safety risks.
➔When working with these substances observe appropriate safety procedures (for
example by wearing goggles, safety gloves and protective clothing) as described in
the material handling and safety data sheet supplied by the vendor, and follow good
laboratory practice.
➔The volume of substances should be reduced to the minimum required for the
analysis.
➔Do not operate the instrument in an explosive atmosphere.
CAUTION
Hot heat exchangers
The column compartment has two heat exchanger assemblies that might be hot.
➔Allow them to cool down before starting repairs.
WARNING
Electrical shock
Repair work at the module can lead to personal injuries, e.g. shock hazard, when the
cover is opened.
➔Do not remove the cover of the module.
➔Only certified persons are authorized to carry out repairs inside the module.
114 1290 Infinity TCC User Manual
8Maintenance
Cautions and Warnings
WARNING
The module is partially energized when switched off, as long as the power cord is
plugged in.
Repair work at the module can lead to personal injuries, e.g. electrical shock, when
the cover is opened and the module is connected to power.
➔Always unplug the power cable before opening the cover.
➔Do not connect the power cable to the instrument while the covers are removed.
WARNING
Personal injury or damage to the product
Agilent is not responsible for any damages caused, in whole or in part, by improper
use of the products, unauthorized alterations, adjustments or modifications to the
products, failure to comply with procedures in Agilent product user guides, or use of
the products in violation of applicable laws, rules or regulations.
➔Use your Agilent products only in the manner described in the Agilent product user
guides.
CAUTION
Safety standards for external equipment
➔If you connect external equipment to the instrument, make sure that you only use
accessory units tested and approved according to the safety standards appropriate
for the type of external equipment.
CAUTION
Sample degradation and contamination of the instrument
Metal parts in the flow path can interact with the bio-molecules in the sample leading
to sample degradation and contamination.
➔For bio-inert applications, always use dedicated bio-inert parts, which can be
identified by the bio-inert symbol or other markers described in this manual.
➔Do not mix bio-inert and non-inert modules or parts in a bio-inert system.
1290 Infinity TCC User Manual 115
Maintenance 8
Overview of Maintenance
Overview of Maintenance
The following pages describe maintenance procedures (simple repairs) that
can be done without opening the main cover.
Table 20 Maintenance Procedures
Procedure Typical Frequency Notes
“Cleaning the Column
Compartment” on page 116
If required
“Changing Column
Identification Tags” on
page 117
When column performance or new
application requires a change
“Adding Heater Devices” on
page 119
When new application requires a
change
“Installing the capillaries” on
page 124
When new application requires a
change
“Correcting Leaks” on page 131 If a leak has occurred Check for leaks
“Replacing Valve Heads” on
page 136
If the valve performance shows
indication of leakage or wear
“Preparing the Column
Compartment for
Transportation” on page 140
If the TCC shall be transported
“Replacing the Module
Firmware” on page 143
If required
116 1290 Infinity TCC User Manual
8Maintenance
Cleaning the Column Compartment
Cleaning the Column Compartment
To keep the module case clean, use a soft cloth slightly dampened with water,
or a solution of water and mild detergent.
WARNING
Liquid dripping into the electronic compartment of your module can cause shock
hazard and damage the module
➔Do not use an excessively damp cloth during cleaning.
➔Drain all solvent lines before opening any connections in the flow path.
1290 Infinity TCC User Manual 117
Maintenance 8
Changing Column Identification Tags
Changing Column Identification Tags
The column compartment is equipped with a column-identification system,
that stores column specific information. Two identification tag readers are
incorporated in the heat exchanger assemblies.
Figure 25 Column-Identification System
1The identification tag can be easily removed from the column.
2The tag needs to be placed differently, depending on whether the column is
installed at the left or right heat exchanger, see Figure 26 on page 118 and
Figure 27 on page 118. The Agilent logo should always be at front.
8dajbc"^YZci^[^XVi^dciV\
8dajbcXa^e
IV\gZVYZgh
When If column is used on the opposite heat exchanger or a tag is added to a new column.
Parts required # p/n Description
1 5062-8588 Column identification tag (1x), re-order (3/pk)
118 1290 Infinity TCC User Manual
8Maintenance
Changing Column Identification Tags
When correctly placed on the heat exchanger, the distance between tag and
tag reader is 1 – 2 mm. This is the optimum distance for proper function.
Figure 26 Column-Identification Tag for Left Heat Exchanger
Figure 27 Column-Identification Tag for Right Heat Exchanger
3For columns with small diameter, a cable tie wrap should be used to fix the
column identification tag to the column. Assure that the tie wrap does not
block the front cover.
8dajbc"^YZci^[^XVi^dciV\
8dajbc"^YZci^[^XVi^dciV\
1290 Infinity TCC User Manual 119
Maintenance 8
Adding Heater Devices
Adding Heater Devices
The additional heater devices can be arranged in the G1316C in various
locations depending on the application needs. Some examples are shown
below.
Figure 28 Arrangements of Heater and Cooling Devices
120 1290 Infinity TCC User Manual
8Maintenance
Adding Heater Devices
Figure 29 Typical positions of the low dispersion heat exchangers
The heater devices are mounted on a carrier that can be fitted to the left
and/or right heat exchangers.
NOTE
If the additional heater devices are used as shown above, the column identification system
cannot be used. If the column identification system is required, fix the heater devices in the
upper or lower locations or fix them right/left of the current location.
Otros manuales para 1290 infinity
12
Tabla de contenidos
Otros manuales de Equipo de laboratorio de Agilent Technologies
Agilent Technologies
Agilent Technologies 5DX 5000 Series Manual de usuario
Agilent Technologies
Agilent Technologies 7673 Manual de usuario
Agilent Technologies
Agilent Technologies B1500A Manual de usuario
Agilent Technologies
Agilent Technologies Truevolt Series Manual de servicio
Agilent Technologies
Agilent Technologies TriScroll Exhaust Silencer Kit Manual de usuario
Agilent Technologies
Agilent Technologies G2570A GC/MSD Manual del propietario
Agilent Technologies
Agilent Technologies 8890 Manual de usuario
Agilent Technologies
Agilent Technologies G1289 Manual de usuario
Agilent Technologies
Agilent Technologies G2545A Manual de uso y cuidado
Agilent Technologies
Agilent Technologies 16196A Manual de operación
Agilent Technologies
Agilent Technologies 1220 Infinity II LC Series Manual de usuario
Agilent Technologies
Agilent Technologies 7250 Manual de usuario
Agilent Technologies
Agilent Technologies 8860 Hoja de instrucciones
Agilent Technologies
Agilent Technologies Varian CP-8400 Manual de usuario
Agilent Technologies
Agilent Technologies 1200 series Manual de usuario
Agilent Technologies
Agilent Technologies 1260Infinity II Bio-inert FractionCollector Manual de usuario
Agilent Technologies
Agilent Technologies G3183B Instrucciones de funcionamiento
Agilent Technologies
Agilent Technologies 8890 Manual de usuario
Agilent Technologies
Agilent Technologies 1200 series Manual de usuario
Agilent Technologies
Agilent Technologies 1260 Infinity II Manual de usuario
