Advantech PPC-103 Manual de usuario

PPC-103

Celeron®/Pentium™III Panel PC

with 10.4" LCD flat panel display

This document is copyrighted 2000 by Advantech Co. Ltd. All rights are

reserved. Advantech Co., Ltd. reserves the right to make improvements to

the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or

transmitted in any form or by any means without the prior written

permission of Advantech. Information provided in this manual is intended

to be accurate and reliable. However, Advantech assumes no responsibility

for its use, nor for any infringements upon the rights of third parties which

may result from its use.

All brand and product names mentioned herein are trademarks or

registered trademarks of their respective holders.

PartNo.2002010300, 1stEdition

Printed in Taiwan

December2000

iii

FCC Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

environment. This equipment generates, uses and can radiate radio

frequency energy. If not installed and used in accordance with this

user's manual, it may cause harmful interference to radio communica-

tions. Note that even when this equipment is installed and used in

accordance with this user’s manual, there is still no guarantee that

interference will not occur. If this equipment is believed to be causeing

harmful interference to radio or television reception, this can be

determined by turning the equipment on and off. If the interference is

occurring, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to a power outlet on a circuit different from

that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Warning: Any changes or modifications made to the equipment

which are not expressly approved by the relevant stan

dards authority could void your authority to operate the

equipment.

Packing List

Before installing your panel PC, ensure that the following materials

have been received:

• PPC-103seriespanel PC

• User's manual

• Accessories for PPC-103

- Powercable for both FDDand HDD/CD-ROM

- FDDflatcable(35cm)

- Keyboardextension cable (5-pin DIN female to 6-pinPS/2 male)

- FDDpower cable

- HDDflatcable(44-pin)(5cm)

- IDE flatcable(40-pin)(46cm)

- Audio line-in cable

- Power cord (1.8 m) - USA type

- Mounting kits and packet of screws

- Heat sink

- HDDbracket

- Driver/UtilityCD-ROMdisk

- Screws

- Silicon heat sink paste

- CPU push cover

- CPU push screw driver

- Warranty card

- CPUtop plate for FPCGA type CPU

If any of these items are missing or damaged, contact your distributor

or sales representative immediately.

Note:

1. Customers may buy the CPU separately. Do not buy a CPU that

already has a fan attached with adhesive, because it is not easy to

remove such fan.

If you install or upgrade a CPU yourself, you must install the heat sink

assembly from Advantech above the CPU in order to avoid heat

damage to the CPU. The CPU and the heat sink are normally sold

Additional Information and Assistance

1. Visit the Advantech Web site at www.advantech.comwhereyou can

find the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's

customer service center for technical support if you need additional

assistance. Please have the following information ready:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version,

application software, etc.)

• A complete description of the problem

• The exact wording of any error messages

together with the fan attached to the CPU. Due to tight constraints

within the PPC-103’s housing, care must be taken to use the heat sink

in the accessory box which will both cool the CPU and fit within the

PPC-103. Thus you must buy a CPU without a fan attached.

Safety Instructions

1. Please read these safety instructions carefully.

2. Please keep this User's Manual for later reference.

3. Please disconnect this equipment from any AC outlet before cleaning. Do not use

liquid or spray detergents for cleaning. Use a damp cloth.

4. For pluggable equipment, the socket-outlet must be installed near the equipment

and must be easily accessible.

5. Please keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it

fallcouldcausedamage.

7. The openings on the enclosure are for air convection. Protect the equipment from

overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source

to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This could cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened

only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according to

the user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED

ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW

-20° C (-4° F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT.

The sound pressure level at the operator's position according to IEC 704-1:1982 is

equal to or less than 70 dB(A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech

disclaims all responsibility for the accuracy of any statements contained herein.

vii

Wichtige Sicherheishinweise

1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden

Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein ange-

feuchtetes Tuch zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht

zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein

Kippen oder Fallen könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor

überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht

abgedeckt werden.

8. Beachten Sie beim AnschluB an das Stromnetz die AnschluBwerte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.

Es sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu

beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es

vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine

Beschädigung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüs-

sigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elek-

trischen Schlag auslösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu tren-

nen und von einer qualifizierten Servicestelle zu überprüfen:

a - Netzkabel oder Netzstecker sind beschädigt.

b - Flüssigkeit ist in das Gerät eingedrungen.

c - Das Gerät war Feuchtigkeit ausgesetzt.

d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioni

ert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70

dB(A) oder weiger.

DISCLAIMER: This set of instructions is given according to IEC704-1. Advantech

disclaims all responsibility for the accuracy of any statements contained herein.

viii

Contents

Chapter 1 General Information....................... 1

1.1 Introduction ................................................ 2

1.2 Specifications............................................. 3

1.3 General ........................................................ 3

1.4 Interface Standard PC functions ............. 3

1.5 I/O Arrangement ......................................... 8

1.6Cutout (Suggestion) ................................... 9

1.7Mounting .................................................... 10

1.7.1 Panel mounting .....................................................................10

1.7.2 Desktop stand (optional)........................................................ 11

1.7.3 Wall-mounting (optional) ...................................................... 12

Chapter 2 System Setup ............................... 13

2.1General....................................................... 14

2.2Removing Rear Panel ............................... 15

2.3 Installing Options..................................... 16

2.3.1 Installing CPU and heat sink assembly................................. 16

2.3.2 Installing a primary 2.5” HDD (internal) ................................19

2.3.3 Installing the SDRAM Memory Module .................................24

2.3.4 Installing an FDD ....................................................................26

2.4 Installing I/O Equipment .........................26

2.4.1 Installing one secondary HDD/CD-ROM device (external)..26

2.4.3 Parallel port connection .......................................................27

2.4.4 PS/2 keyboard and PS/2 mouse ...........................................27

2.4.5 Mic-in, line-out .......................................................................28

2.4.6 External VGA .........................................................................29

2.4.7 Four serial COM ports............................................................29

2.4.8 Ethernet ..................................................................................29

2.5 Installing Software to the HDD ............... 30

2.5.1 Method 1: Use the Ethernet....................................................30

2.5.2 Method 2: Use an FDD ............................................................30

2.5.3 Method 3: Use the COM or parallel port ...............................30

2.5.4 Method 4: Use a 3.5" HDD or CD-ROM ...................................30

2.6 Exploded Diagram ................................... 31

2.7 PCM-9573 and I/O Adapter

Replacement ................................................... 33

2.8 Power Supply and Cooling Fan Replace-

ment............................................................. 34

Chapter 3 Jumper Settings

and Connectors............................................ 37

3.1 Jumpers and Connectors....................... 38

3.1.1 Setting jumpers.......................................................................38

3.1.2 Jumpers and switch................................................................39

3.1.3 Locating jumpers and switch.................................................40

3.1.4Connectors ..............................................................................41

3.1.5 Locating connectors ...............................................................42

3.3 CMOS Clear for External RTC (JP7)...... 43

3.4 COM-port Interface .................................. 43

3.4.1 COM2 RS-232/422/485 setting (JP2, JP3, JP4) .......................43

3.4.2 COM3 / COM4 pin 9 output type setting (JP5) .......................45

3.5VGA Interface............................................. 45

3.5.1 LCD panel power setting........................................................45

3.5.2 Panel type select (SW1) .........................................................45

3.6 Watchdog Timer Configuration.............. 46

3.6.1 Watchdog activity selection (JP6) .........................................46

Chapter 4 Award BIOS Setup ....................... 47

4.1 Award BIOS Setup ................................... 48

4.2 CMOS Setup Utility................................... 48

4.3 Standard CMOS Setup ............................ 49

4.3.1 Hard disk configurations ........................................................ 49

4.4 BIOS Features Setup ............................... 51

4.5 Chipset Features Setup .......................... 54

4.6 Power Management Setup ..................... 57

4.7 PNP/PCI Configuration Setup................. 59

4.8 Load BIOS Defaults .................................60

4.9 Load Setup Defaults ................................ 61

4.10 Integrated Peripherals .......................... 61

4.11 Password Setting................................... 63

4.12 IDE HDD Auto Detection........................ 64

4.13 Save and Exit Setup .............................. 65

4.14 Exit Without Saving................................ 65

CHAPTER 5 PCI Bus Ethernet Interface...... 67

5.1 Introduction .............................................. 68

5.2 Installation of Ethernet Driver ................ 68

5.2.1 Installation for Windows 95 ................................................... 69

5.2.2 Installation for Windows 98 ................................................... 72

5.2.3 Installation for Windows NT...................................................76

5.3Further Information .................................. 78

Chapter 6 PCI SVGA Setup ........................... 79

6.1 Introduction .............................................. 80

6.1.1 Chipset.....................................................................................80

6.1.2 Display memory ......................................................................80

6.1.3 Display types ........................................................................... 80

6.2 Installation of SVGA Driver ..................... 80

Tabla de contenidos

Otros manuales de Panel táctil de Advantech

Advantech

Advantech PPC-315W TGL Manual de instalación y operación

Advantech

Advantech IPPC-6152 Series Manual de usuario

Advantech

Advantech PPC-612 Manual de instalación y operación

Advantech

Advantech PPC-157T Manual de usuario

Advantech

Advantech IPPC-9151G Manual de usuario

Advantech

Advantech PPC-S155T Manual de usuario

Advantech

Advantech TPC-300 Elkhart Lake Series Manual de usuario

Advantech

Advantech PPC-306 EHL Manual de instalación y operación

Advantech

Advantech PPC-3150 Manual de usuario

Advantech

Advantech IPPC-7157 Series Manual de usuario

Advantech

Advantech Intel XScale PXA Touch Panel Computer TPC-66... Manual de usuario

Advantech

Advantech TPC-60S Manual de usuario

Advantech

Advantech PPC-3150SW-PN4A Manual de usuario

Advantech

Advantech PPC-L128T Manual de usuario

Advantech

Advantech TPC-1270 Manual de usuario

Advantech

Advantech PPC-3150 Manual de usuario

Advantech

Advantech PPC-S154T Manual de usuario

Advantech

Advantech POC-W211 Manual de instrucciones

Advantech

Advantech IPPC-6172F Series Manual de usuario

Advantech

Advantech SPC-821-6 Series Manual de usuario

Advantech

Advantech IPPC-6152A Manual de usuario

Advantech

Advantech PPC-155T Manual de usuario

Advantech

Advantech TPC-1071H Manual de usuario

Advantech

Advantech UTC-520F Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

B&R Industries

B&R Industries MAPPC900-ENG Manual de usuario