Advantech SPC-821-6 Series Manual de usuario

User Manual

SPC-815

SPC-821

電腦

Multi-Touch Panel Computer

with Intel Skylake Processor

&Extension Units

SPC-800 User Manual ii

The documentation and the software included with this product are copyrighted 2020

by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right

to improve the products described in this manual at any time without notice. No part

of this manual may be reproduced, copied, translated, or transmitted in any form or

by any means without the prior written permission of Advantech Co., Ltd. The infor-

mation provided in this manual is intended to be accurate and reliable. However,

Advantech Co., Ltd. assumes no responsibility for its use, nor for any infringements

of the rights of third parties that may result from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.

Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

http://support.advantech.com/

This Manual Covers the Following Models:

SPC-821

SPC-821-6XXXXXXXXXXXXXXXX

SPC8216XXXXXXXXXXXXXXXX

(Where "x" may be any alphanumeric character, "-" or blank)

SPC-815

SPC-815-6XXXXXXXXXXXXXXXX

SPC8156XXXXXXXXXXXXXXXX

(Where "x" may be any alphanumeric character, "-" or blank)

iii SPC-800 User Manual

Product Warranty (2 years)

Advantech warrants the original purchaser that each of its products will be free from

defects in materials and workmanship for two years from the date of purchase.

This warranty does not apply to any products that have been repaired or altered by

persons other than repair personnel authorized by Advantech, or products that have

been subject to misuse, abuse, accident, or improper installation. Advantech

assumes no liability under the terms of this warranty as a consequence of such

events.

Because of Advantech’s high quality-control standards and rigorous testing, most

customers never need to use our repair service. If an Advantech product is defective,

it will be repaired or replaced at no charge during the warranty period. For out-of-war-

ranty repairs, customers are billed according to the cost of replacement materials,

service time, and freight. Please consult your dealer for more details.

If you suspect that your product is defective product, follow the steps outlined below.

1. Collect all the information about the problem encountered (for example, CPU

speed, Advantech products used, other hardware and software used, etc.). Note

anything abnormal and list any onscreen messages displayed when the prob-

lem occurs.

2. Call your dealer and describe the problem. Please have your manual, product,

and any helpful information readily available.

3. If your product is diagnosed as defective, obtain a return merchandize authori-

zation (RMA) number from your dealer. This allows us to process your return

more quickly.

4. Carefully pack the defective product, a completed Repair and Replacement

Order Card, and a proof of purchase date (such as a photocopy of your sales

receipt) into a shippable container. Products returned without a proof of pur-

chase date are not eligible for warranty service.

5. Write the RMA number clearly on the outside of the packaging, and ship the

package prepaid to your dealer.

Part No. 2003C80010 Edition 1

Printed in China July 2020

SPC-800 User Manual iv

Declaration of Conformity

This product has passed the CE test for environmental specifications when shielded

cables are used for external wiring. We recommend the use of shielded cables. This

type of cable is available from Advantech. Please contact your local supplier for

ordering information.

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A dig-

ital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-

vide reasonable protection against harmful interference when the equipment is

operated in a commercial environment. This equipment generates, uses, and can

radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Opera-

tion of this equipment in a residential area is likely to cause harmful interference. In

such cases, users are required to correct the interference at their own expense.

警告使用者

這是甲類測試產品，在居住的環境中使用時，可能會造成射頻干擾，在這種情況下，

使用者會被要求採取某些適當的對策。

Technical Support and Assistance

1. Visit the Advantech website at www.advantech.com/support to obtain the latest

product information.

2. Contact your distributor, sales representative, or Advantech's customer service

center for technical support if you need additional assistance. Please have the

following information ready before you call:

–Product name and serial number

–Description of your peripheral attachments

–Description of your software (operating system, version, application software,

etc.)

–A complete description of the problem

–The exact wording of any error messages

Safety Precaution - Static Electricity

Follow these simple precautions to protect yourself from harm and the products from

damage.

To avoid electrical shock, always disconnect the power from the PC chassis

before manual handling. Do not touch any components on the CPU card or

other cards while the PC is powered on.

Disconnect the power before making any configuration changes. The sudden

rush of power when connecting a jumper or installing a card may damage sensi-

tive electronic components.

v SPC-800 User Manual

Safety Instructions

1. Read these safety instructions carefully.

2. Retain this user manual for future reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp

cloth for cleaning. Do not use liquid or spray detergents.

4. For pluggable equipment, the power outlet socket should be located near the

equipment and easily accessible.

5. Protect the equipment from humidity.

6. Place the equipment on a reliable surface during installation. Dropping or letting

the equipment fall may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment

from overheating. Do not cover the openings.

8. Ensure that the voltage of the power source is correct before connecting the

equipment to a power outlet.

9. Position the power cord away from high-traffic areas. Do not place anything over

the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source

to avoid damage from transient overvoltage.

12. Never pour liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following occurs, have the equipment checked by service person-

nel:

–The power cord or plug is damaged.

–Liquid has penetrated the equipment.

–The equipment has been exposed to moisture.

–The equipment is malfunctioning or does not operate according to the user

manual.

–The equipment has been dropped and damaged.

–The equipment shows obvious signs of breakage.

15. Do not leave this equipment in an environment with a storage temperature of

below -20 °C (-4 °F) or above 60 °C (140 °F).

16. Batteries that are incorrectly replaced are at risk of exploding. Replace only with

the same or equivalent type recommend by the manufacturer. Discard used bat-

teries according to the manufacturer’s instructions.

17. In accordance with IEC 704-1:1982 specifications, the sound pressure level at

the operator's position does not exceed 70 dB (A).

18. Please Keep the monitor out of direct sunlight, very strong bright lights and

away from any other heat source. Lengthy exposure to this type of environment

may result in discoloration and damage to the monitor.

DISCLAIMER: These instructions are provided according to the IEC 704-1. Advant-

ech disclaims all responsibility for the accuracy of any statements contained herein.

Caution! Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type recommended by the manufacturer. Dis-

pose of used batteries according to the manufacturer's instructions.

SPC-800 User Manual vi

Consignes de sécurité

1. Lire attentivement les instructions de sécurité

2. Conserver ce manuel pour utilisation ultérieure

3. Débranchez cet équipement de toute prise secteur avant de le nettoyer. Utilisez

seulement un chiffon humide. N'utilisez pas de détergent liquide ou pulvérisé

pour le nettoyage.

4. Gardez cet équipement à l'abri de l'humidité.

5. Placez cet équipement sur une surface fiable pendant l'installation. Le faire ou

bien le laisser tomber peut causer des dégâts.

6. Les ouvertures sur l'enceinte servent à la convection de l'air. Protégez l'équipe-

ment contre la surchauffe. NE COUVREZ PAS LES OUVERTURES.

7. Assurez-vous que la tension de la source d'alimentation est correcte avant de

connecter l'équipement à l'alimentation.

8. Placez le câble d'alimentation de manière à ce que personne ne puisse marcher

dessus. Ne placez rien sur le câble d'alimentation.

9. Toutes les mises en garde et tous les avertissements sur l'équipement doivent

être notés.

10. Si l'équipement n'est pas utilisé pendant une longue période, débranchez-le de

la source d'alimentation pour éviter tout endommagement dû à une surtension

transitoire.

11. Ne jamais verser de liquide dans une ouverture. Cela pourrait provoquer un

incendie ou un choc électrique.

12. N'ouvrez jamais l'équipement. Pour des raisons de sécurité, l'équipement doit

être ouvert uniquement par du personnel qualifié.

13. Si l'une des situations suivantes se présente, faites vérifier l'équipement par le

personnel de service:

– Un liquide a pénétré dans l'équipement.

– L'équipement a été exposé à l'humidité.

– L'équipement ne fonctionne pas bien, ou vous ne pouvez pas le faire

fonctionner selon le manuel de l'utilisateur.

– L'équipement est tombé et endommagé.

– L'équipement présente des signes évidents de rupture.

14. NE LAISSEZ PAS CET ÉQUIPEMENT DANS UN ENVIRONNEMENT OU LA

TEMPÉRATURE DE STOCKAGE PEUT ÊTRE INFÉRIEURE À -20 ° C (-4 ° F)

OU BIEN SUPÉRIEURE À 60 ° C (140 ° F). CECI POURRAIT ENDOMMAGER

L'EQUIPEMENT. L'ÉQUIPEMENT DEVRAIT ÊTRE DANS UN ENVIRONNE-

MENT CONTRÔLÉ.

15. ATTENTION: DANGER D'EXPLOSION SI LA BATTERIE EST INCORRECTE-

MENT REMPLACÉE. REMPLACER SEULEMENT AVEC LE MÊME TYPE OU

ÉQUIVALENT RECOMMANDÉ PAR LE FABRICANT, JETER LES BATTERIES

USÉES SELON LES INSTRUCTIONS DU FABRICANT. VEUILLEZ CON-

TACTER LE FABRICANT, ADVANTECH, POUR LE REMPLACER.

Le niveau de la pression acoustique à la position de l'opérateur, conformément à la

norme CEI 704-1: 1982, ne dépasse pas 70 dB (A).

AVIS DE NON-RESPONSABILITÉ: Cet ensemble d'instructions est donné conformé-

ment à la CEI 704-1. Advantech décline toute responsabilité quant à l'exactitude des

déclarations contenues dans ce document.

–"Si l'équipement est utilisé d'une manière non spécifiée par le fabricant, la

protection fournie par l'équipement peut être compromise"

–Instructions pour l'installation dans un environnement de degré de pollution 2

(pour l'usage d'intérieur, altitude jusqu'à 2.000m) ou déclaration équivalente.

vii SPC-800 User Manual

Avertissement! DANGER D'EXPLOSION SI LA BATTERIE EST INCORRECTE-

MENT REMPLACEE. REMPLACER SEULEMENT AVEC LE

MÊME TYPE OU ÉQUIVALENT RECOMMANDÉ PAR LE FAB-

RICANT, JETER LES BATTERIES USÉES SELON LES

INSTRUCTIONS DU FABRICANT. VEUILLEZ CONTACTER LE

FABRICANT, ADVANTECH, POUR LE REMPLACER.

ATTENTION! Pour éviter les chocs. Ne pas retirer lecouvercle. Aucune pièce

réparable par l’utilisa- teur. Pour l’entertien adressez-vours aux

personnes qulifiées, s.v.p.

SPC-800 User Manual viii

安全指示

1. 請仔細閱讀此安全操作說明。

2. 請妥善保存此用戶手冊供日後參考。

3. 用濕抹布清洗設備前，請確認拔除電源線。請勿使用液體或去污噴霧劑清洗設

備。

4. 對於使用電源線的設備，設備周圍必須有容易接觸到的電源插座。

5. 請勿在潮濕環境中試用設備。

6. 請在安裝前確保設備放置在可靠的平面上，意外摔落可能會導致設備損壞。

7. 設備機殼的開孔適用於空氣對，從而防止設備過熱。請勿覆蓋開孔。

8. 當您連接設備到電源插座前，請確認電源插座的電壓符合要求。

9. 請將電源線佈置在人們不易絆倒的位置，請勿在電源線上覆蓋任何雜物。

10. 請注意設備上所有的警告標示。

11. 如果長時間不使用設備，請拔除與電源插座的連結，避免設備被超標的電壓波動

損壞。

12. 請勿讓任何液體流入通風口，以免引起火灾或短路。

13. 請勿自行打開設備。為了確保您的安全，請透過經認證的工程師來打開設備。

14. 如遇下列情况，請由專業人員維修：

–電源線或插頭損壞；

–設備內部有液體流入；

–設備曾暴露在過度潮濕環境中使用；

–設備無法正常工作，或您無法透過用戶手冊來正常工作；

–設備摔落或損壞；

–設備有明顯外觀損；

15. 請勿將設備放置在超出建議溫度範圍的環境，即不要低於 -20 ℃ （-4 ℉）或高

於 60 ℃ （140 ℉），否則可能會造成設備損壞。

16. 注意：若電池更換不正確，將有爆炸危險。因此，只可以使用製造商推薦的同一

種或者同等型號的電池進行替換。請按照製造商的指示處理舊電池。

17. 根據 IEC 704‐1:1982 規定，操作員所在位置音量不可高於 70 分貝。

18. 限制區域：請勿將設備安裝於限制區域使用。

19. 免責聲明：請安全訓示符合 IEC 704‐1 要求。研華公司對其內容之準確性不承

擔任何法律責任。

20. 使用過度恐傷害視力。

21. 使用 30 分鐘請休息 10 分鐘。

22. 未滿 2 歲幼兒不看螢幕，2 歲以上每天看螢幕不要超過 1 小時。

23. 請避免顯示器遭受陽光直射，並遠離強光及其他熱源。若長時間接觸此類環境，

顯示器可能會褪色及損壞。

ix SPC-800 User Manual

Contents

Chapter 1 General Information ............................1

1.1 Introduction ............................................................................................... 2

1.2 Packing List............................................................................................... 3

1.3 Specifications............................................................................................ 3

1.3.1 System Kernel............................................................................... 3

1.3.2 I/O Ports........................................................................................ 3

1.3.3 Safety and Environment................................................................ 3

1.4 Panel PC Specifications............................................................................ 4

1.4.1 Without Button extension for built in SPC-815-6X3AG & SPC-821-

6X3AG Panel PC .......................................................................... 4

1.4.2 Button extension for built in SPC-815-6X3AP & SPC-821-6X3AP

Panel PC....................................................................................... 6

1.5 Power ........................................................................................................ 7

1.6 I/O Ports Arrangement .............................................................................. 8

Figure 1.1 SPC-800 Front view and Side view............................ 8

Figure 1.2 SPC-800 Rear View- I/O Port Arrangement............... 8

1.7 Hardware Specifications ........................................................................... 9

Figure 1.3 SPC-815 Dimensions ................................................. 9

Figure 1.4 SPC-821 Dimensions ............................................... 10

Chapter 2 System Setup.....................................11

2.1 Scope of Delivery.................................................................................... 12

Figure 2.1 Unpack the Package ................................................ 12

2.1.1 Accessory BOX........................................................................... 12

2.1.2 Pole Mount Kit BOX.................................................................... 13

2.2 System Setup.......................................................................................... 13

2.3 Mounting the SPC-800 device ................................................................ 16

2.3.1 SPC-800 device for support ARM Mounting............................... 16

2.3.2 SPC-800 device for support VESA Mounting ............................. 19

2.4 SPC-800 Extension with Operator Controls............................................ 25

2.5 Installing the Drivers................................................................................ 30

2.5.1 Installation of Touch Screen driver ............................................. 30

2.5.2 Installation of Watchdog driver.................................................... 30

2.5.3 Installation of Brightness Control Driver...................................... 32

2.5.4 Installation of EC Lmsensor Driver ............................................. 34

Chapter 3 Features of Windows Embedded OS

.............................................................39

3.1 Features in Windows Embedded OS ...................................................... 40

3.2 Enhanced Write Filter (EWF) .................................................................. 40

3.3 File-Based Write Filter (FBWF) ............................................................... 41

Appendix A UI Operating Process ........................43

A.1 UI Operating Process.............................................................................. 44

Table A.1: Status indicator table................................................ 44

Table A.2: Button code definition............................................... 49

SPC-800 User Manual x

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Panel táctil de Advantech

Advantech

Advantech PPC-3100-RE9A Manual de instalación y operación

Advantech

Advantech PPC-315W TGL Manual de instalación y operación

Advantech

Advantech PPC-100 Manual de usuario

Advantech

Advantech TPC-650H Manual de usuario

Advantech

Advantech TPC-1881WP Series Manual de usuario

Advantech

Advantech POC-W152 Manual de instrucciones

Advantech

Advantech IPPC-6152 Series Manual de usuario

Advantech

Advantech PPC-A84 Manual de usuario

Advantech

Advantech TPC-100W Series Manual de usuario

Advantech

Advantech IDK-1105 Series Manual de usuario

Advantech

Advantech PPC-125 Manual de usuario

Advantech

Advantech IPPC-5211WS Series Manual de usuario

Advantech

Advantech PPC-6151C Manual de usuario

Advantech

Advantech TPC-1261H Manual de usuario

Advantech

Advantech PPC-3151SW Manual de usuario

Advantech

Advantech PPC-3211SW Manual de instalación y operación

Advantech

Advantech PPC-6151C Manual de usuario

Advantech

Advantech TPC-1582H Manual de usuario

Advantech

Advantech TPC-1260H Manual de usuario

Advantech

Advantech TPC-300 Series Manual de usuario

Advantech

Advantech TPC-1270 Manual de usuario

Advantech

Advantech PPC-3211SW Manual de usuario

Advantech

Advantech PPC-157T Manual de usuario

Advantech

Advantech PPC-306 EHL Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

B&R Industries

B&R Industries MAPPC900-ENG Manual de usuario