Advantech PPC-105 Manual de usuario

PPC-105

NS GX1 processor-based Panel PC

with 10” TFT LCD flat panel display

User’s Manual

This document is copyrighted 2001 by Advantech Co. Ltd. All rights are

reserved. Advantech Co., Ltd. reserves the right to make improvements to

the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or

transmitted in any form or by any means without the prior written

permission of Advantech. Information provided in this manual is intended

to be accurate and reliable. However, Advantech assumes no responsibility

for its use, nor for any infringements upon the rights of third parties which

may result from its use.

All brand and product names mentioned herein are trademarks or

registered trademarks of their respective holders.

Part No. 2008010500, 1st Edition

Printed in Taiwan June 2001

iii

FCC Class B

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference when the equipment is operated in a residential

environment. This equipment generates, uses and can radiate radio

frequency energy. If not installed and used in accordance with this

user's manual, it may cause harmful interference to radio communica-

tions. Note that even when this equipment is installed and used in

accordance with this user’s manual, there is still no guarantee that

interference will not occur. If this equipment is believed to be causeing

harmful interference to radio or television reception, this can be

determined by turning the equipment on and off. If the interference is

occurring, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and the receiver

• Connect the equipment to a power outlet on a circuit different from

that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help

Warning: Any changes or modifications made to the equipment

which are not expressly approved by the relevant stan

dards authority could void your authority to operate the

equipment.

Additional Information and Assistance

1. Visit the Advantech Web site at www.advantech.com where you can

find the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's

customer service center for technical support if you need additional

assistance. Please have the following information ready:

• Product name and serial number

• Description of your peripheral attachments

• Description of your software (operating system, version,

application software, etc.)

• A complete description of the problem

• The exact wording of any error messages

Packing List

Before installing your panel PC, ensure that the following materials

have been received:

• PPC-105 series panel PC

• User's manual

• Accessories for PPC-105

- Power cable for both FDD and HDD/CD-ROM

- FDD flat cable (35 cm)

- Keyboard extension cable (5-pin DIN female to 6-pin PS/2

male)

- HDD flat cable (44-pin) (8 cm)

- IDE flat cable (40-pin) (45 cm)

- Power cord (1.8 m) - USA type

- HDD bracket

- Driver/Utility CD-ROM disk

- Screws

- Warranty card

If any of these items are missing or damaged, contact your distributor

or sales representative immediately.

Safety Instructions

1. Please read these safety instructions carefully.

2. Please keep this User's Manual for later reference.

3. Please disconnect this equipment from any AC outlet before cleaning. Do not use

liquid or spray detergents for cleaning. Use a damp cloth.

4. For pluggable equipment, the socket-outlet must be installed near the equipment

and must be easily accessible.

5. Please keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it

fall could cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment from

overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything

over the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source

to avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This could cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be opened

only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.

d. The equipment does not work well, or you cannot get it to work according to

the user's manual.

e. The equipment has been dropped and damaged.

f. The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED

ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS BELOW

-20° C (-4° F) OR ABOVE 60° C (140° F). IT MAY DAMAGE THE EQUIPMENT.

The sound pressure level at the operator's position according to IEC 704-1:1982 is

equal to or less than 70 dB(A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech

disclaims all responsibility for the accuracy of any statements contained herein.

Wichtige Sicherheishinweise

1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.

2. Heben Sie diese Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden

Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein ange-

feuchtetes Tuch zur Reinigung.

4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht

zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein

Kippen oder Fallen könnte Verletzungen hervorrufen.

7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor

überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht

abgedeckt werden.

8. Beachten Sie beim AnschluB an das Stromnetz die AnschluBwerte.

9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen kann.

Es sollte auch nichts auf der Leitung abgestellt werden.

10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu

beachten.

11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es

vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine

Beschädigung vermieden.

12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüs-

sigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elek-

trischen Schlag auslösen.

13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen

Sicherheit nur von authorisiertem Servicepersonal geöffnet werden.

14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu tren-

nen und von einer qualifizierten Servicestelle zu überprüfen:

a - Netzkabel oder Netzstecker sind beschädigt.

b - Flüssigkeit ist in das Gerät eingedrungen.

c - Das Gerät war Feuchtigkeit ausgesetzt.

d - Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioni

ert oder Sie mit Hilfe dieser Anleitung keine Verbesserung erzielen.

e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.

f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000 beträgt 70

dB(A) oder weiger.

DISCLAIMER: This set of instructions is given according to IEC704-1. Advantech

disclaims all responsibility for the accuracy of any statements contained herein.

vii

Contents

Chapter 1 General Information....................... 1

1.1 Introduction .................................................................. 2

1.2 Specifications ............................................................. 2

General ................................................................................... 2

Standard PC functions .............................................................2

Solid State Disk (SSD) ............................................................ 3

PCI SVGA/flat panel interface ..................................................3

Audio function: ......................................................................... 4

PCI bus Ethernet interface ....................................................... 4

Touchscreen (optional) ............................................................. 4

Environment ............................................................................. 4

1.3 LCD Specifications ..................................................... 5

1.4 Dimensions ................................................................. 6

1.5 I/O Arrangement .......................................................... 7

1.6 Cutout (Suggestion) .................................................... 8

1.7 Mounting ..................................................................... 9

1.7.1 Panel mounting .............................................................. 9

1.7.2 Desktop stand (optional) .............................................. 10

1.7.3 Wall-mounting (optional) ............................................... 11

Chapter 2 System Setup ............................... 13

2.1 General ..................................................................... 14

2.2 Preparing For First Time Usage ................................ 14

2.3 Installing Options ....................................................... 15

2.3.1 Removing Rear Panel .................................................... 15

2.3.2 Installing a primary 2.5" HDD (internal) ......................... 16

2.4 Installing I/O Equipment ............................................. 18

2.4.1 Installing one secondary

HDD/CD-ROM device (external) ..................................... 18

viii

2.4.2 Installing an FDD ........................................................... 18

2.4.3 Parallel port connection ................................................. 19

2.4.4 PS/2 keyboard and PS/2 mouse ................................... 19

2.4.5 Mic-in, line-out .............................................................. 20

2.4.6 External VGA ................................................................ 20

2.4.7 Four serial COM ports ................................................... 20

2.4.8 Ethernet ........................................................................ 20

2.4.9 USB ports ..................................................................... 21

2.5 Installing Software to the HDD ................................... 21

2.5.1 Method 1: Use the Ethernet .......................................... 21

2.5.2 Method 2: Use an FDD .................................................. 21

2.5.3 Method 3: Use the COM or parallel port ........................ 21

2.5.4 Method 4: Use a 3.5" HDD or CD-ROM ......................... 21

2.6 Exploded Diagram .................................................... 22

2.7 PCM-5821 and I/O Adapter Replacement ................. 23

Chapter 3 The Engine of

the PPC-105T (PCM-5821) ........................... 25

3.1 Introduction ................................................................ 26

3.2 Features ................................................................... 27

3.3 Jumpers and Connectors .......................................... 28

3.3.1 Setting jumpers ............................................................. 28

3.3.2 Jumpers ........................................................................ 29

3.3.3 Connectors ................................................................... 30

3.4 Wake on LAN Selection (Reserved) (JP1) ................. 33

3.5 CMOS Clear (JP2) .................................................... 33

3.6 Watchdog Timer Configuration .................................. 33

3.6.1 Watchdog activity selection (JP2) ................................. 34

3.7 COM2 RS-232/422/485 setting (JP3, JP4,JP5) ........ 34

3.8 Buzzer enable (JP10) ................................................ 35

Chapter 4 PCI Bus Ethernet Interface ......... 37

4.1 Introduction ................................................................ 38

4.2 Installation of Ethernet Driver ..................................... 38

4.2.1 Installation for WINDOWS 95 ........................................ 39

4.2.2 Installation for WINDOWS 98 ........................................ 42

4.2.3 Installation for WINDOWS NT ........................................ 43

4.3 Further Information .................................................... 48

Chapter 5 PCI SVGA Setup ........................... 49

5.1 Introduction ................................................................ 50

5.1.1 Chipset ......................................................................... 50

5.1.2 Display memory ............................................................ 50

5.1.3 Display types ................................................................ 50

5.2 Installation of SVGA Driver ........................................ 50

5.2.1 Installation for Windows 95 ............................................ 52

5.2.2 Installation for WINDOWS 98 ....................................... 56

5.2.3 Installation for WINDOWS NT ........................................ 59

5.3 Further Information .................................................... 61

Chapter 6 Audio Setup .................................. 63

6.1 Introduction ................................................................ 64

6.2 Installation of Audio Driver ......................................... 64

6.2.1 Installation for Windows 95 ............................................ 65

6.2.3 Installation for WINDOWS NT ........................................ 68

6.2.2 Installation for Windows 98 ............................................ 68

6.3 Further Information .................................................... 71

Chapter 7 Award BIOS Setup ....................... 73

7.1 Award BIOS Setup .................................................... 74

7.2 CMOS Setup Utility ................................................... 74

7.3 Standard CMOS Setup ............................................. 75

7.3.1 Hard Disk Configurations ............................................... 76

7.4 BIOS Features Setup ................................................ 77

7.5 Chipset Features Setup ............................................ 80

7.6 Power Management Setup ........................................ 81

7.7 PNP/PCI Configuration Setup ................................... 83

7.8 Load BIOS Defaults .................................................. 84

7.9 Load Setup Defaults.................................................. 85

7.10 Integrated Peripherals ............................................. 85

WDT Active When Power ON ................................................. 87

7.11 Password Setting .................................................... 88

7.12 IDE HDD Auto Detection ......................................... 88

7.13 Save and Exit Setup ................................................ 89

7.14 Exit Without Saving ................................................. 89

Chapter 8 Touch Screen ............................... 91

8.1 Introduction ................................................................ 92

8.1.3 Environmental specifications ......................................... 92

8.2 Installation of Driver for Resistive Touch Screen ......... 93

Appendix A Programming the Watchdog

Timer ......................................................... 105

A.1 Programming the Watchdog Timer .......................... 106

Appendix B Power Supply Specifications 107

B.1 Introduction ............................................................. 108

B.2 Input Specifications ................................................. 108

B.3 Output Specifications .............................................. 108

B.4 Environmental Specifications .................................. 108

B.5 Features ................................................................. 108

Appendix C I/O Pin Assignments ............... 111

C.1 Keyboard connector (CN5-1) .................................. 112

C.2 Mouse connector (CN5-2) ....................................... 112

C. 3 VGA connector (CN6) ............................................ 113

C.4 COM1 RS-232 serial port (CN1-2) .......................... 113

C.5 COM3 RS-232 serial port connector (CN2-1).......... 114

C.6 COM4 RS-232 serial port connector (CN2-2).......... 114

C.7 COM2 Connector ................................................... 115

C.8 Parallel port connector (CN1-1) .............................. 116

Tabla de contenidos

Otros manuales de Panel táctil de Advantech

Advantech

Advantech SPC-200 Series Manual de usuario

Advantech

Advantech PCM-3335 Manual de usuario

Advantech

Advantech PPC-L128T Manual de usuario

Advantech

Advantech PPC-A84 Manual de usuario

Advantech

Advantech SPC-821-6 Series Manual de usuario

Advantech

Advantech TPC-870 Manual de usuario

Advantech

Advantech IPPC-6152F Series Manual de usuario

Advantech

Advantech TPC 40 Series Manual de usuario

Advantech

Advantech TPC-1770 Manual de usuario

Advantech

Advantech TPC-100W Series Manual de usuario

Advantech

Advantech POC-621 Series Manual de usuario

Advantech

Advantech PPC-6120 Manual de usuario

Advantech

Advantech TPC-B610 Manual de usuario

Advantech

Advantech PPC-123 Manual de usuario

Advantech

Advantech PPC-3151-650AE Manual de instalación y operación

Advantech

Advantech PPC-57 Series Manual de usuario

Advantech

Advantech TPC-1560 Manual de usuario

Advantech

Advantech PPC Series Manual de usuario

Advantech

Advantech TPC-1251T-Exxx Series Manual de usuario

Advantech

Advantech TPC-650H Manual de usuario

Advantech

Advantech PPC-3060S Manual de usuario

Advantech

Advantech ITA-8100 Manual de usuario

Advantech

Advantech PPC-3211SW Manual de instalación y operación

Advantech

Advantech PPC-306 EHL Manual de usuario

Manuales populares de Panel táctil de otras marcas

FlowLine

FlowLine Data loop Manual de usuario

ALPEX

ALPEX AEx-8 P Series Manual de usuario

Ltech

Ltech E5S Manual de usuario

Harman

Harman AMX MODERO S MSD-701-L2 Manual de usuario

Acnodes

Acnodes PC 1150 Manual de usuario

AIS

AIS IP10IA99 series Manual de usuario

IBASE Technology

IBASE Technology ASTUT-152-RE1S Manual de usuario

YASKAWA

YASKAWA TP 610C Manual de usuario

B&R

B&R Power Panel C Series Manual de usuario

Beijer Electronics

Beijer Electronics X2 control Manual de usuario

AXIOMTEK

AXIOMTEK GOT321W-521 Manual de usuario

TRIDONIC.ATCO

TRIDONIC.ATCO x-touchBOX Manual de usuario

Qomo

Qomo QIT1386 Manual de usuario

DFI

DFI KS104-CD Manual de usuario

AMX

AMX AXP-PPC Guía

Sartorius

Sartorius X3 PR 5410 Manual de usuario

AMX

AMX Modero X Series Manual de usuario

B&R Industries

B&R Industries MAPPC900-ENG Manual de usuario