ADTRAN SMART/RG SR516ac Manual de usuario

SR516ac

Quick Start Guide

Installation

1. Connect one end of the included phone cable to the DSL port on the gateway and connect the other end to the

wall jack.

2. Connect one end of an Ethernet cable to a LAN port of the gateway and connect the other end to your PC.

3. Plug the power adapter into the wall outlet and connect the other end of it to the Power port of the gateway.

4. Turn on the unit by pressing the On/Off button on the left side of the gateway.

Your gateway is now automatically being set up to connect to the Internet. This process may take a few minutes to

complete before you can begin using your Internet applications (browser, email, etc.).

Notes:

lIf you use 3G WAN service, connect the 3G USB data card to the USB port of the gateway. If you use the Ethernet

uplink, connect to the WAN port with an Ethernet cable.

lYou cannot use the xDSL uplink, 3G WAN service, and Ethernet uplink at the same time.

If you are unable to connect to the Internet, confirm that all connections are in place and the gateway is turned on.

LED Indicators

The LEDs on the front of the SR516ac gateway can help you

understand the current state of your adapter.

Legend: White White blinking Red Green Green blinking

LED Action Explanation

All LEDs

except

those

listed below

Feature enabled &/or working correctly

Data being transferred

POWER Device in CFE mode

Device powered on and ready for use

WAN WAN connection active

LAN LAN connection active

Data being transferred

Quick Gateway Configuration

Warning: Do not press the Reset button unless you want to clear the current settings. The Reset button is in a small

round hole on the rear panel. If you want to restore the default settings, insert a thin wire (such as a paper clip) into

the hole, press the button for 1 second, and then release the button. The system reboots and returns to the factory

defaults.

Logging in to your gateway

To change the settings on your gateway, you must log in to the gateway's interface. Make sure that you have completed

the steps in "Installation" before you begin.

1. Open your internet browser application and type 192.168.1.1 into the address line. The login dialog appears.

2. Enter the factory default credentials shown below and click OK.

User Name: admin Password: admin

Note: Your service provider may use other settings. Contact your provider for details.

Configuring the WAN manually

If the automatic connect process is unsuccessful, refer to the Advanced Setup >Layer 2 Interface and WAN Service

sections of the SmartRG SR516ac Gateway User Manual to manually establish a connection.

WiFi Setup

Two methods, WPS and Manual, are available for WiFi setup. Perform the steps on this page first, and then follow

the instructions for the applicable method. The default settings work for most situations.

1. In the left menu, click Wireless and then click 2.4 GHz Band or 5 GHz Band. The fields are the same for both

options. The wireless radio is enabled by default.

2. If desired, in the SSID field, enter the network name to which you want your client devices connected.

Continue with the steps in the method you prefer.

3. Continue with the steps for the method you prefer.

WPS Method

If the device you wish to connect to the Internet via your gateway supports the WPS secure Wi-Fi connection method,

follow these steps.

1. In the left navigation bar, click Wireless, click the band that you want to configure, and then click Security.

2. In the Enable WPS field, make sure that Enabled is selected, and then click Apply/Save to save your change.

3. On the left side of the gateway:

a. Activate the desired band by pressing 2.4 GHz or 5 GHz briefly on the rocker switch.

b. Activate WPS by pressing the desired band button and holding it down for 7 seconds.

4. Within 2 minutes, activate WPS on the 3rd party device to which you wish to connect. The device may have a

push button on its exterior that you can press, or a clickable button on a software interface. To learn how to use

the WPS feature on your client device, refer to its documentation.

Your device should now be connected to your gateway wirelessly using WPS. If you encounter problems with the WPS

setup such as connection failure, refer to your client device for further instructions.

Manual Method

Set up your gateway’s parameters first, then follow these steps.

1. In the left menu, click Wireless, the band that you want to configure, and then click Security.

2. Scroll down to the Manual Setup AP section.

3. If your gateway supports multiple wireless networks, select the SSID of the network you wish to configure. You

will need this ID for step 8.

4. Select the desired Network Authentication. Make sure that the host devices you intend to use support the

selected authentication type.

Otros manuales para SMART/RG SR516ac

Tabla de contenidos

Otros manuales de Puerta de ADTRAN

ADTRAN

ADTRAN NETVANTA 640 Series Manual de usuario

ADTRAN

ADTRAN TOTAL ACCESS 234 Manual de usuario

ADTRAN

ADTRAN NetVanta 6240 Series Manual de usuario

ADTRAN

ADTRAN 825-v6 Manual del propietario

ADTRAN

ADTRAN jobAid+ Total Access 311 Manual de usuario

ADTRAN

ADTRAN 424RG Manual de usuario

ADTRAN

ADTRAN Atlas 830 Manual de usuario

ADTRAN

ADTRAN Total Access 912 Manual de usuario

ADTRAN

ADTRAN 7310-8 Manual de usuario

ADTRAN

ADTRAN SMART/RG SR555ac Manual de usuario

ADTRAN

ADTRAN 17600072F1S Manual de usuario

ADTRAN

ADTRAN SMART/RG SR905ac Manual de usuario

ADTRAN

ADTRAN SmartRG SR400ac Manual de usuario

ADTRAN

ADTRAN 17600139F1 Manual de usuario

ADTRAN

ADTRAN 6304W Manual de usuario

ADTRAN

ADTRAN NetVanta 644 Manual de usuario

ADTRAN

ADTRAN 617600132F1-13A Manual de usuario

ADTRAN

ADTRAN Total Access 916 Manual

ADTRAN

ADTRAN SDX810-RG Manual de usuario

ADTRAN

ADTRAN SR905acv Manual de usuario

ADTRAN

ADTRAN Total Access 908e Manual

ADTRAN

ADTRAN NetVanta 6240 Series Manual de usuario

ADTRAN

ADTRAN SmartRG SR400ac Manual de usuario

ADTRAN

ADTRAN SR700ac Manual de usuario

Manuales populares de Puerta de otras marcas

LST

LST M500RFE-AS Manual de usuario

Kinnex

Kinnex Media Gateway Manual de usuario

2N Telekomunikace

2N Telekomunikace 2N StarGate Manual de usuario

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manual de usuario

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manual de usuario

Telsey

Telsey CPVA 500 - SIP Manual de usuario

RTA

RTA 460A-NNA4 Hoja de especificaciones

Shaw

Shaw Gateway HDPVR Manual de usuario

ABB

ABB VSN900 Guía de inicio rápido

Commander

Commander Pulse Manual de usuario

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manual de usuario

NETGEAR

NETGEAR C6300BD Manual de usuario

Amit

Amit CDW531AM Manual de usuario

HMS

HMS Netbiter EasyConnect EC150 Manual de usuario

Huawei

Huawei EchoLife HG620 Manual de usuario

AT&T

AT&T U-verse 3801 Manual de uso y cuidado

Logic IO

Logic IO RTCU MX2 turbo Manual de usuario

Suttle

Suttle MediaMAX MXM-521 Manual de usuario