ADC HiGain HTC-439 List 2 Test Card Manual de usuario
HiGain
HiGain
USER MANUAL
HTC-439 List 2 HiGain Test Card
Product Catalog: 150-439-102-02
CLEI: T1DQACBJ
150-439-102-02, Issue 2
ii November 12, 1999 HTC-439 List 2
Revision History of This Manual
To order copies of this document, use document catalog number
150-439-102-02.
Copyright
November 12, 1999
© 1999 ADC DSL Systems, Inc. All rights reserved.
Trademark Information
ADC is a registered trademark of ADC Telecommunications, Inc. HiGain is a
registered trademark of ADC DSL Systems, Inc. No right, license, or interest to such
trademarksis granted hereunder,andyou agree that no suchright, license,or interest
shall be asserted by you with respect to such trademark.
Other product names mentioned in this practice are used for identification purposes
only and may be trademarks or registered trademarks of their respective companies.
Disclaimer of Liability
Information contained in this documentis company private to ADCDSL Systems,Inc.,
and shall not be modified, used, copied, reproduced or disclosed in whole or in part
without the written consent of ADC.
Contents herein are current as of the date of publication. ADC reserves the right to
change the contents without prior notice. In no event shall ADC be liable for any
damages resulting from loss of data, loss of use, or loss of profits, and ADC further
disclaims any and all liability for indirect, incidental, special, consequential or other
similar damages. This disclaimer of liability applies to all products, publications and
services during and after the warranty period.
Issue Release Date Revisions Made
1November 12, 1999 Initial Release
2April 16, 2002 ADC Rebranding
150-439-102-02, Issue 2 Using This Manual
HTC-439 List 2 November 12, 1999 iii
USING THIS MANUAL
Three types of messages, identified by icons, appear in text.
UNPACK AND INSPECT YOUR SHIPMENT
Upon receipt of the equipment:
•Unpack each container and inspect the contents for signs of damage. If
theequipmenthasbeendamagedintransit,immediatelyreporttheextent
of damage to the transportation company and to ADC DSL Systems, Inc.
Order replacement equipment, if necessary.
•Check the packing list to ensure complete and accurate shipment of each
listed item. If the shipment is short or irregular, contact ADC DSL
Systems, Inc. as described in Product Support on page 12. If you must
store the equipment for a prolonged period, store the equipment in its
original container.
Notes contain information about special circumstances.
Cautions indicate the possibility of personal injury or
equipment damage.
The Electrostatic Discharge (ESD) symbol indicates that a
deviceorassemblyissusceptibletodamagefromelectrostatic
discharge.
Table of Contents 150-439-102-02, Issue 2
iv November 12, 1999 HTC-439 List 2
TABLE OF CONTENTS
Overview________________________________________________1
Features ....................................................................................1
Test Card ..................................................................................2
Installation ______________________________________________3
Testing a Circuit__________________________________________3
Appendix A - Specifications ________________________________6
Appendix B - Product Support______________________________7
Appendix C - Glossary ____________________________________8
Certification andWarranty _________________Inside Back Cover
150-439-102-02, Issue 2 Overview
HTC-439 List 2 November 12, 1999 1
OVERVIEW
The ADCHiGainTest Card HTC-439 List 2 provides a convenient
method of testing Central Office (CO) and Field Tip and Ring transmit and
receive pairs from any standard T1-239 repeater slot.
The width of theHTC-439 List 2 has been reduced from the List1 unit so that
the List 2 fits a four-slot HRE-504 enclosure without interfering with plugs
above or below it.
FEATURES
•Four-position slider switch (S1) that allows you to select tests on the
transmit (XMT) and receive (RCV) Tip and Ring pairs on CO and field
circuits:
–Open
–Short
–Loop Thru
–Loop Back (metallic)
•Test points that provide access to Tip and Ring circuits (CO and field)
and to frame ground.
•Miniature210 jacks located withinthe J1block that provideaccessto CO
and field Tip and Ring circuit sides.
•Designed to extend beyond the front plane of the shelf or enclosure into
which the HTC-439 List 2 is inserted to permit easy access to its test
points.
•Compatible with all ADC enclosures that support T1-239 mechanics.
Overview 150-439-102-02, Issue 2
2 November 12, 1999 HTC-439 List 2
TEST CARD
Test points on the HTC-439 (Figure 1) provide access to each active
card-edge connector pin including Frame Ground. These test points are
identified by the pin number to which they connect.
•The four-position test slider switch (S1) selects which test (Open, Short,
Loop Thru, or Loop Back) is to be performed on CO and field circuits.
•The Open switch position effectively provides a splitting-type access to
one pair of the CO and field sides and the 210 jacks.
•The Loop Back or Loop Thru switch positions allow you to use the two
miniature 210 jacks located within the J1 block.
All tests are run on both Side 1 and Side 2. Refer to “Testing a Circuit” on
page 3 for further information.
Figure 1. HTC-439 List 2 Test Card
CO
SIDE 1
SIDE 1
T
T
R
R
TP6
TP5
TP8
TP9
CO
CO
TP4
TP3
TP11
TP12
TP1
FIELD
FIELD
OPEN
SHORT
LOOP THRU
LOOP BACK
FIELD
SIDE 2
SIDE 2
S1 switch
S1 switch
positions Circuit schematic
Connector pins
1
12
Miniature
210 jacks
Test points
150-439-102-02, Issue 2 Installation
HTC-439 List 2 November 12, 1999 3
INSTALLATION
1Insert the HTC-439 into the shelf slot for the channel you want to test.
2Push the card into the slot until it is firmly seated.
TESTING ACIRCUIT
Use the HTC-439 to test circuits, as follows:
1Set the S1 slider switch to the test you want to perform (Open, Short,
Loop Thru, or Loop Back).
2Connect to test points as applicable. The connections of Tip and Ring
pairs of CO and field circuits for each setting of the switch are listed in
Table 1 on page 4 and illustrated in Figure 2 on page 5. (Pin numbers
correspond to the edge connector pins for each circuit.)
3Perform the selected test.
4Monitor the circuits at the corresponding test points on the card.
5Repeat steps 1 through 4 as required.
Allwiring externalto theproductshould follow the provisions
of the current edition of the National Electrical Code.
Testing a Circuit 150-439-102-02, Issue 2
4 November 12, 1999 HTC-439 List 2
Table 1. Test Connections
Connect Pin Number To Pin Number
Loopback - This switch position connects the following circuits
CO Tip 6CO Tip 9
CO Ring 5CO Ring 8
Field Tip 4Field Tip 12
Field Ring 3Field Ring 11
Loopthru - This switch position connects the following circuits
CO Tip 6Field Tip 4
CO Ring 5Field Ring 3
CO Tip 9Field Tip 12
CO Ring 8Field Ring 11
Short - This switch position connects the following circuits
CO Tip 6CO Ring 5
CO Tip 9CO Ring 8
Field Tip 4Field Ring 3
Field Tip 12 Field Ring 11
Open - This switch position removes all connections between the circuits
150-439-102-02, Issue 2 Testing a Circuit
HTC-439 List 2 November 12, 1999 5
Figure 2. HTC-439 List 2 Test Connections
CO
SIDE 1
FIELD
SIDE 2
To/From
CO Equipment
TP1
Test point 6
(TP6)
LOOP THRU TIP
TIP
RING
RING
SIDE 1
SIDE 2
6
9
5
8
TIP
TIP
RING
RING
4
3
12
11
SHORT TIP
TIP
RING
RING
SIDE 1
SIDE 2
6
9
5
8
TIP
TIP
RING
RING
4
3
12
11
OPEN TIP
TIP
RING
RING
SIDE 1
SIDE 2
6
9
5
8
TIP
TIP
RING
RING
4
3
12
11
To/From
Field
Equipment
1
10
FRAME GND
FRAME GND
LOOP BACK TIP
TIP
RING
RING
SIDE 1
SIDE 2
TIP
TIP
RING
RING
9
5
8
4
3
12
11
TP6 TP4
TP5 TP3
TP9 TP12
TP8 TP11
6
SIDE 1
T
T
R
R
TP6
TP5
TP8
TP9
CO
CO
TP4
TP3
TP11
TP12
TP1
FIELD
FIELD
OPEN
SHORT
LOOP THRU
LOOP BACK
SIDE 2
Appendix A - Specifications 150-439-102-02, Issue 2
6 November 12, 1999 HTC-439 List 2
APPENDIX A - SPECIFICATIONS
Mounting Any T1-239 repeater mechanics slot
Environmental
Operating Temperature: 40 °F to + 149 °F (-40 °C to + 65 °C)
Operating Humidity: 5% to 95% (non condensing)
Dimensions and Weight
Height: 2.5 in (6.33 cm)
Width: 0.6 in (1.52 cm)
Depth: 8.4 in (21.34 cm)
Weight: 0.30 lb (0.66 kg)
Tabla de contenidos
Otros manuales de Hardware de red de ADC
ADC
ADC UniPatch Modular System RS-422 Manual de usuario
ADC
ADC LoopStar 750 Manual de usuario
ADC
ADC OmniReach NCX-1000 Manual de usuario
ADC
ADC H2TU-C-388 HiGain Instrucciones de funcionamiento originales
ADC
ADC LSA-PLUS NT Manual de usuario
ADC
ADC HiGain HXU-358 Manual de usuario
ADC
ADC DSX-4R (RZX3) Manual de usuario
ADC
ADC HiGain H2TU-C-319 List 4E Instrucciones de funcionamiento originales
ADC
ADC HiGain H2TU-C-231 Instrucciones de funcionamiento originales
ADC
ADC FPL Series Manual de usuario
ADC
ADC HiGain H2TU-R-402 List 7A Instrucciones de funcionamiento originales
ADC
ADC OmniReach MDU Rapid Fiber System Manual de usuario
ADC
ADC FMT Drawers Featuring MicroVAM Modules Manual de usuario
ADC
ADC WorldDSL UTU-701C Manual de usuario
ADC
ADC H2TU-C-202 Manual de usuario
ADC
ADC PG-FlexPlus ARL-942 Manual de usuario
ADC
ADC HiGain HLU-200 Manual de usuario
ADC
ADC Baluns Series Manual de usuario
ADC
ADC GPRS Support Node GGSN & SGSN WAVE.GSN Manual de usuario
ADC
ADC OmniReach oFDT-48 Manual de usuario
Manuales populares de Hardware de red de otras marcas
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manual de usuario
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manual de usuario
Yudor
Yudor YDS-16 Manual de usuario
D-Link
D-Link ShareCenter DNS-320L Manual de usuario
Samsung
Samsung ES1642dc Instrucciones de uso
Honeywell Home
Honeywell Home LTEM-PV Instrucciones de montaje
