Adam Equipment MDW - 300L Manual de usuario

Page 1

Adam Equipment

MDW – 300L

HEALTH AND FITNESS SCALE with BMI

ADAM EQUIPMENT CO. LTD.

p.n. 700660159 Rev. A2, Apr 2014

Page 2

CONTENTS

1.0

INTRODUCTION...........................................................................................3

2.0

TECHNICAL SPECIFICATIONS...................................................................3

3.0

DISPLAY AND KEY DESCRIPTIONS ..........................................................4

4.0

SETTING UP THE SCALE............................................................................5

5.0

FUNCTION ...................................................................................................7

5.1

WEIGHING................................................................................................7

5.2

MEASURING HEIGHT..............................................................................8

5.3

MEASURING BODY MASS INDEX (BMI).................................................8

6.0

CALIBRATION..............................................................................................9

7.0

USER PARAMETERS ................................................................................10

8.0

RS232 COMMUNICATIONS.......................................................................11

9.0

ERROR MESSAGES..................................................................................15

10.0

WARNING...................................................................................................15

WARRANTY INFORMATION................................................................................17

Page 3

1.0 INTRODUCTION

•The MDW 300L scale is a Digital Health and Fitness Scale with Body Mass

Index (BMI) readout.

•It is an accurate electronic device with advanced design and stable

performance.

•It is designed to measure both the weight and the height of a person and

compute the BMI index.

2.0 TECHNICAL SPECIFICATIONS

Maximum capacity 300 kg / 660lb

Minimum capacity 2 kg / 4lb

Scale division 0.05kg / 0.1lb

Height range 60 cm-212 cm / 24”-83”

Division of measurement

(height used in BMI calculation)

entry via keypad 1cm / 0.5”

Division of measurement

(height measurement)

0.1cm /

⅛

”

Display LED display

Size of platform 375 X 275 mm

14.75” X 10.8”

Overall dimension, height

pillar in lowest position 570 X 275 X 1310 mm

22.4” X 10.8” X 51.5”

Net weight 13 kg / 29 lb.

Environment for Use Temperature: 5ºC-40ºC;

Humidity: <85℅RH

Power 12vDC 500mA adapter

Battery Internal, re-chargeable

6V 4Ah, 50 hours approx.

Calibration External calibration through the keypad.

Page 4

3.0 DISPLAY AND KEY DESCRIPTIONS

KEYS

FUNCTIONS

[On

/Off /

Zero] To turn the scale on or off.

To zero the scale if the display drifts from zero.

[Tare] ↵

↵↵

↵To tare the scale, if necessary. Accept settings as required

[Units

BMI] 



To toggle the weighing unit between Kg and Lb. and to select the BMI

function. Move active digit to the right when required.

[

Pri

Hold] 



To lock the reading even if the person to be weighed is moving and

also to print the weight via the RS232 interface. Increase value or

settings when required.

DISPLAY

DESCRIPTIONS

Indicates when the scale is weighing in Kilograms.

Indicates when the scale is weighing in Pounds.

Hold

Indicates when the scale has held the weight reading shown on the

display. It will flash until it locks into the stable reading when it will then

remain on for a preset time when it has held the displayed reading.

BMI

Indicates when the scale is displaying the Body Mass Index value.

The charge light will be on when the battery is recharging.

This indicates when the scale is being used with the AC adapter.

ZERO This indicator will be displayed in the left cornerwhen the scale reaches

zero.

NET

The Net weight is displayed, Tare weight is at zero.

Page 5

4.0 SETTING UP THE SCALE

•Take the scale out of the box.

1. Locate the 4 screws (2)

2. Place the cable (4) through the pillar

(3).

3. Insert the 4 screws (2) through the

holes on the pillar bracket and secure

the bracket to the indicator (1),

4. Make sure the screws are securely

tightened.

5. Place the cable (4) into the tube

support (6) on the scale base.

6. Insert the pillar (3) into the tube

support (6).

7. Rotate the pillar to position the

indicator (1) in the direction desired,

and then secure using the 2 screws

(5) into the fixing tube (6).

8. Locate the load cell cable (13) ready for

connection

Page 6

9. Place the indicator cable (4) and the

load cell cable (13) together near the hole

on the base (16).

10. Plug the two connectors (15) together.

11. Position the connector inside the base

(16).

12. The cables should be fixed to the base

using the clip provided (14).

13. Locate the fixing bolt and washer

(10) used to secure the height rod to

the scale base (11)

14. Locate the height rod (7) onto the

fixing points (9) of the upper and lower

brackets (8) & (12).

15. Secure the bolt and washer to the

bracket on the base (10)

16. Tighten the bolt on the upper

bracket (9).

Page 7

5.0 FUNCTION

5.1 WEIGHING

•Place the Scale on an even floor and press the [On/Off] key.

•The instrument performs a self-test after which it is ready for operation.

•Press the [On/Off] key and the machine switches off.

•The person to be weighed can step on to the platform once the scale shows

0.0 on the display. The weight will be display in Kg. or lb. depending on the

units chosen by the user.

•If the weighing value is to be tared press the tare key to remove the weight

value from the display.

•Press the [Units] key for changing the weighing unit to kg or lb. The LED will

indicate the chosen weighing unit.

•Overload display: When “

FULL

” appears on the display, it shows that the load

on the platform is over the maximum capacity. Under these circumstances, it

is necessary to reduce the load otherwise the sensor or the platform will be

damaged.

•Hold Function: To lock the weighing result, press the [Print/Hold] key. The

LED will flash until a stable reading has been obtained and then it will light up

constantly. The weight will be displayed until the hold time has expired (see

Sec 7.0) or to manually release the function, press the [Print/Hold] key again.

•Print Function: To send the weighing result to a printer or computer press the

[Print/Hold] key when the [Print/Hold] key has been set up in the parameter

section to work as print function.

Page 8

5.2 MEASURING HEIGHT

•To measure someones height, it is necessary to extract the measuring rod and

place the height arm on top of the head of the person being measured.

•For shorter heights the height arm can be released by pressing the red button

on the top of the height rod, and then moving the height arm to the lower

section of the height pillar.

•The height is read on the bar at the top of the support. The height can be read

in either centimetres or inches,

5.3 MEASURING BODY MASS INDEX (BMI)

•Once the height has been determined it is possible to enter the height reading

into the display ready for the scale to compute the BMI.

•Press and hold the [Unit/BMI] key to enter the BMI mode. The display will

show the last height value used, “Cm123” or “In123” depending on which

weighing unit you are currently using.

•The height entry unit (Cm or In) will be flashing to show you which unit you are

currently in, use the Up arrow key to change the height entry unit between Cm

to In as required

•Enter your height using the arrow keys, the [Print/Hold] /key will increment

the flashing digit, the right arrow, the [Unit/BMI] /key, will move the flashing

digit to the adjacent digit.

•Press the [Tare]/↵

↵↵

↵key to confirm the value.

•The display will now show the BMI based on the current weight on the scale

and the height entered.

•Press the [Unit/BMI] key to exit the BMI mode and return to normal weighing.

•The Hold function will work as described above whilst in the BMI mode.

Page 9

6.0 CALIBRATION

Before calibrating the scale, you should ensure that you have a suitable known weight for

calibration.

1. When in normal weighing mode with the scale at zero press and hold down [TARE] and

[ON / OFF] keys to enter the calibration mode.

2. If the calibration switch is in the off position on the main PCB inside the scale, the

indicator will show “CAL.OFF” and then exit this mode. If the indicator shows “CAL-?”,

the scale is ready for calibration.

3. When the indicator shows “CAL-?”, press the [TARE] key to confirm and go to next step,

or press the [ON / OFF] key to exit the calibration mode.

4. When ‘0.0’ is displayed the scale will begin to calibrate the scale’s zero-point. Ensure

that there is no load or weight on the scale’s platform. Press the [TARE] key to confirm,

or press the [ON / OFF] key to exit this mode.

5. A few seconds after the [TARE] key has been pressed in step 4 the scale will show

“300.0” and the kg LED, or “600.0” and the lb LED depending on which unit you chosen,

this is the default calibration weight from the factory. Press the [UNIT] key to select the

calibration weight unit that you want to calibrate in. Press the [ON / OFF] key to exit the

calibration mode at this point or press the [Print/Hold] key to choose a different

calibration weight value (50kg, 100kg, 150kg, 200kg, 250kg, 300kg or 100lb, 200lb,

300lb, 400lb, 500lb, 600lb); Then put on the weight that you selected and press the

[TARE] key to confirm the chosen standard weight that was selected earlier. The

displayed data will flash on the display and if the scale accepts the calibration data it will

calculate and store the information into the EEPROM. If an error has occurred, the scale

will display “CAL. Er” and return back to step 4 for re-calibration. If the loaded weight is

not within the range of 95% to 105% of the weight value you selected, the scale will not

calibrate but display “CAL. Er” and return back to step 4 for re-calibration. )

6. Check the calibration by putting the weight that you calibrated at back on the scale, if it

is off repeat the calibration process again.

Page 10

7.0 USER PARAMETERS

This indicator has 4 parameter settings that can be selected.

When the scale is in normal weighing mode, press and hold down the [ON / OFF] key

and the [UNIT] key for 3 seconds until ‘Setup’ is shown on the display.

When in the SETUP mode, press the [Print/Hold] key to change the flashing digits, and

[TARE] key to confirm the flashing digits and move to the next parameter setting. Press

the [ON / OFF] key to exit the set up mode.

Parameters setting summary:

Parameter x/xy Factory Set

Setting

A.o.t. 00-15 05 Auto-off time:

No auto-off = 00.

01-15 minutes auto-off time.

P.H. 0,1,2 1

0 = Only Print Function

1 = Only Hold Function

2 = both HOLD and PRINT function (pressed

down less 3s,this key works as Print

function; pressed down more than 3s,this

key works as HOLD function)

H.t 0-4 0

Hold time:

0 = no time limit.

1 = 10 seconds

2 = 30 seconds

3 = 60 seconds

4 = 120 seconds

S.F. 0-3 0

0 = No RS232 Function.

1 = Continuously outputs display data.

2 = Output display data when PRINT pressed

3 = Bi-directional communication (the scale

receives and executes commands from the

HOST device)

Tabla de contenidos

Otros manuales de Escala de Adam Equipment

Adam Equipment

Adam Equipment BFW 75 Manual de usuario

Adam Equipment

Adam Equipment PGL SERIES Manual de usuario

Adam Equipment

Adam Equipment LBX 12 Manual de usuario

Adam Equipment

Adam Equipment WBW Series Cómo utilizar

Adam Equipment

Adam Equipment ACBplus Series Manual de usuario

Adam Equipment

Adam Equipment ABK Series Manual de usuario

Adam Equipment

Adam Equipment CBD 100a Manual de usuario

Adam Equipment

Adam Equipment Eclipse EBL Series Manual de usuario

Adam Equipment

Adam Equipment MDW-160M Manual de usuario

Adam Equipment

Adam Equipment SHS Series Manual de usuario

Adam Equipment

Adam Equipment CQT1751GR Manual de usuario

Adam Equipment

Adam Equipment WBW 30aM Manual de usuario

Adam Equipment

Adam Equipment 700660189 Manual de usuario

Adam Equipment

Adam Equipment AQ Series Manual de usuario

Adam Equipment

Adam Equipment CQT 202 Instrucciones de montaje

Adam Equipment

Adam Equipment CCEU-20 Manual de usuario

Adam Equipment

Adam Equipment SWZ 6D Manual de usuario

Adam Equipment

Adam Equipment GK series Manual de usuario

Adam Equipment

Adam Equipment MDW-160M Manual de usuario

Adam Equipment

Adam Equipment MDW - 250L Manual de usuario

Adam Equipment

Adam Equipment CBC 3 Manual de usuario

Adam Equipment

Adam Equipment CBK-M Series Manual de usuario

Adam Equipment

Adam Equipment CPW 25 Manual de usuario

Adam Equipment

Adam Equipment CORE SERIES Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario