Adam Equipment WBW Series Cómo utilizar

Adam Equipment

WBW & WBW-M SERIES

(P.N. 3036610540, Revision A1, Oct 2009)

Adam Equipment strives to be more environmentally focused and uses recycled materials and

environmentally friendly packaging where possible. As part of this initiative we have developed a short

manual that uses less paper and ink to describe the main functions of your new Adam indicator/scale. A

complete version is available at www.adamequipment.com. Thank you for your support of Adam Equipment

and we hope that you enjoy your new scale.

P a g e 1© Adam Equipment Company 2009

CONTENT

1.0

SETTING UP AND TURNING ON THE SCALES ................................2

2.0

OPERATION.........................................................................................2

2.1

NUMERIC ENTRY METHOD .............................................................2

2.2

ZEROING...........................................................................................2

2.3

TARING .............................................................................................2

2.4

WEIGHING.........................................................................................3

2.5

CHECK-WEIGHING...........................................................................3

3.0

RS-232 SPECIFICATION......................................................................4

4.0

CALIBRATION......................................................................................4

5.0

ERROR CODES....................................................................................5

6.0

SPECIFICATIONS ................................................................................6

7.0

ERROR MESSAGES ............................................................................9

8.0

MENU STRUCTURE...........................................................................10

9.0

WARRANTY INFORMATION .............................................................11

10.0

SERVICE INFORMATION ...............................................................12

P a g e 2© Adam Equipment Company 2009

1.0

SETTING UP AND TURNING ON THE SCALES

There are three series within the range- WBW-M, WBW and WBWa. The WBW-M scales are configured at

the factory for compliance with EN 45501, OIML R-76. They have different capacities and readabilities from

the standard WBW series. The WBW series are similar to the WBWa series except the WBW scales are

usually set for metric units, whereas for the WBWa series are usually set for imperial units.

SETTING UP

The WBW Series comes with a stainless steel pan. Place it on the top if already not installed. Do not press

with excessive force as this could damage the load cell inside.

Level the scale by adjusting the four feet. The scale should be adjusted such that the bubble in the spirit

level is in the centre of the level and the scale is supported by all four feet. Attach the power supply module

to the bottom of the scale and plug into the mains. Press the [O/I] key to start. The software revision number

will be displayed followed by a self-test showing all digits before the zero is displayed along with the unit of

weight that was selected last.

NOTE: the scale can be operated from the battery. If desired, the battery life is approximately 50 hours.

When the battery needs charging a symbol on the display will turn on.

The battery should be charged for 12

hours for full capacity.

2.0 OPERATION

2.1 NUMERIC

ENTRY

METHOD

To set a value when required, use the keys as given below-

- [Limit] key to increase the flashing digit

- [Unit] key to move to the next digit and

- [Tare] key to accept the value

2.2 ZEROING

You can press the [Zero] key at any time to set the zero point from which all other weighing and counting is

measured. The scales have an automatic re-zeroing

function to account for minor drifting or accumulation of

material on a connected platform. However you may

need to press [Zero] to re-zero the scale if small amount

of weight is still shown when the platform is empty.

2.3 TARING

Zero the scale by pressing [Zero]. The zero indicator will be on. Place a container on the pan.

Press [Tare] when the reading is stable. The weight that was displayed is stored as the tare value, leaving

zero on the display. The stable and

Net

indicator will be on.

As a sample is added only the weight of the product will be shown. The scale could be tared a second time if

another type of product was added to the first one.

P a g e 3© Adam Equipment Company 2009

Press [Tare] or [Zero] to remove the tare value and display zero. The

Net

indicator will disappear.

2.4 WEIGHING

To determine the weight of a sample, first tare an empty container if used, then place the sample in the

container. The display will show the weight and the unit of weight currently in use. To change the weighing

unit press the [Unit] key.

2.5 CHECK-WEIGHING

Check-weighing is a procedure to show a display or sound an alarm when the weight on the platform meets

or exceeds the values stored in the memory. The memory holds values for a high limit and a low limit.

Either or both the limits can be set by the user.

The LCD display will indicate whenever the weight is within or exceeds the limits by showing

“OK”

(mass is

between the limits),

“HI”

(mass is above the high limit) or

“LO”

( mass is below the low limit).

The limits can be locked by the manager (see the menu structure section) .A Limit Password must be used

to change the limits or recall other limits from memory.

Setting up the limits

In normal weighing, Press the [Limit] key. It will show the current high limit.The user will be asked for the

password if the current check-weighing password is anything other than “0000”. See the parameter

“F4 PS”

in menu structure. Enter the correct password using the numeric entry method as mentioned in section 2.1. If

the password is “0000” it will display the last used high limit. The

“HI”

symbol will appear on the display.

Press [Tare] to accept the displayed high limit or enter the new high limit using the numeric entry method

(see section 2.1). When the desired value is entered press [Tare] to accept the value. The

“LO”

symbol will

be on. Display will show the last used low limit. Set the low limit in the same way the high limit was set.

Pressing the [Tare] key will return the scale to weighing, with the Check-weighing function enabled.

NOTE: The limits are displayed in the weighing unit in use. The decimal point is fixed at the position that is

used for the current weighing unit. If the weighing unit is pounds:ounces, the limits are entered in pounds

and decimal parts of pounds. i.e. 6,0125 lb.

Limits stored in memory

If the scale is turned off it stores the last high and low limits in the memory along with information about the

weighing unit in use when the limits were stored. If the scale is turned on again, the limits and the weighing

unit will be active.

P a g e 4© Adam Equipment Company 2009

3.0 RS-232 SPECIFICATION

The RS-232 is not available in WBW scales.

4.0 CALIBRATION

The WBW-M scales should not be calibrated by the user. Calibration of the scales may make it illegal to use

the scales. Contact your local metrology standards office for further assistance.

The WBW non-approved scales are calibrated using metric weights when the weighing unit selected is either

kilograms or grams and using pound masses when the weighing unit selected is either pounds, ounces or

pounds:ounces.

To start the calibration turn the scale off and then turn it on again. Press [Tare] during the self-test. Scale

will show

“P- - - - “

. Enter code number “0000” using the numeric entry method (see section2.1) and press

[Tare]. This will take you directly to the calibration section.Display will show

"UnLoAd"

Remove all weight from the pan and then press the [Tare] key when the scale is stable. After the Zero point

is set, the display will show

“Ld xx”

. Place the suggested calibration mass on the pan. It is best to use a

weight close to the full capacity of the scale. If the mass is different from the displayed value, enter the value

of the mass in whole numbers using the numeric entry method (see section 2.1). The kg or the lb symbol will

be on to show the active unit.

Press the [Tare] key when the stable indicator is on. The scale will calibrate to the mass and then return to

weighing. Remove the calibration weight as soon as calibration is complete.

P a g e 5© Adam Equipment Company 2009

5.0 ERROR CODES

During the initial power-on testing or during operation, the scale may show an error message. The meaning

of the error messages is described below.

If an error message is shown, repeat the step that caused the message. If the error message is still shown

then contact your dealer for support.

ERROR

CODE

DESCRIPTION POSSIBLE CAUSES

Err 4

Err 4Err 4

Err 4

Initial Zero is greater than

allowed (4% of maximum

capacity) when power is turned

on or when [Zero] is pressed.

Weight on the pan when turning the scale on.

Excessive weight on the pan when zeroing the scale.

Platform is not installed.

Improper calibration of the scale.

Damaged load cell.

Damaged Electronics.

Err 6

Err 6Err 6

Err 6

A/D count is not correct when

turning the scale on.

Load cell is damaged.

Electronics is damaged.

Err 8

Err 8Err 8

Err 8

High limit input error Low limit is set first, then the high limit is set lower

than the low limit and high limit not equal to zero.

Err 9

Err 9Err 9

Err 9

Low limit input error High limit is set first, then the low limit is set higher

than the high limit and low limit not equal to zero.

FAIL H or

FAIL H or FAIL H or

FAIL H or

FAIL L

FAIL LFAIL L

FAIL L

Calibration error Improper calibration (should be within +10% of the

factory calibration). The old calibration data will be

retained until the calibration process is complete.

P a g e 6© Adam Equipment Company 2009

.0 SPECIFICATIONS

EC Type Approved Models

WBW 3M WBW 6M WBW 15M

Kilograms

Max 3 kg 6 kg 15 kg

e = 0.001 kg 0.002 kg 0.005 kg

Grams

Max 3000 g 6000 g 15000 g

e = 1 g 2 g 5 g

WBW 2 / 5a WBW 4 / 9a WBW 8 / 18a WBW 16 / 35a

Kilograms

Maximum Capacity 2.000 kg 4.000 kg 8.000 kg 16.000 kg

Tare Range -2.000 kg -4.000 kg -8.000 kg -16.000 kg

Readability 0.0002 kg 0.0005 kg 0.001 kg 0.002 kg

Repeatability (S.D.) 0.0002 kg 0.0005 kg 0.001 kg 0.002 kg

Linearity (±) 0.0004 kg 0.001 kg 0.002 kg 0.004 kg

Grams

Maximum Capacity 2000 g 4000 g 8000 g 16000 g

Tare Range -2000 g -4000 g -8000 g -16000 g

Readability 0.2 g 0.5 g 1 g 2 g

Repeatability (S.D.) 0.2 g 0.5 g 1 g 2 g

Linearity (±) 0.4 g 1 g 2 g 4 g

P a g e 7© Adam Equipment Company 2009

Pounds

Maximum Capacity 5 lb 9 lb 18 lb 35 lb

Tare Range -5 lb -9 lb -18 lb -35 lb

Readability 0.0005 lb 0.001 lb 0.002 lb 0.005 lb

Repeatability (S.D.) 0.0005 lb 0.001 lb 0.002 lb 0.005 lb

Linearity (±) 0.001 lb 0.002 lb 0.004 lb 0.01 lb

Ounces

Maximum Capacity 80 oz 144 oz 288 oz 560 oz

Readability 0.01 oz 0.02 oz 0.05 oz 0.1 oz

Repeatability (S.D.) 0.01 oz 0.02 oz 0.05 oz 0.1 oz

Linearity (±) 0.02 oz 0.04 oz 0.1 oz 0.2 oz

Pounds:Ounces

Maximum Capacity 5 lb: 0.00 oz 9 lb:0.00 oz 18 lb:0.0 oz 35 lb: 0.0 oz

Readability 0.01 oz 0.02 oz 0.1 oz 0.1 oz

Repeatability (S.D.) 0.01 oz 0.02 oz 0.1 oz 0.1 oz

Linearity (±) 0.02 oz 0.04 oz 0.2 oz 0.2 oz

OTHER SPECIFICATIONS

Units of measure WBW-M : kg, g

WBW/WBW.a: kg, g, lb, oz, lb:oz

Tare Full range

Stabilisation Time 2 seconds typical

Operating Temperature

-10°C to 40°C

Power supply 12 VDC, 800 Ma through an external Power Supply Module

Battery Internal rechargeable battery (~50 hours operation)

P a g e 8© Adam Equipment Company 2009

Calibration Automatic External

Display 6 digits LCD digital display with capacity tracker and symbols for units

Scale Housing IP 65 Sealed ABS Plastic housing with Stainless Steel pan

Pan Size 210 x 173 mm

Overall Dimensions

(wxdxh)

231 x 265 x 153 mm

Net Weight 3.3 kg / 7.26 lb

Applications Weighing Scales

Functions Weighing, Check weighing

Otros manuales para WBW Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Escala de Adam Equipment

Adam Equipment

Adam Equipment MDW-160M Manual de usuario

Adam Equipment

Adam Equipment WBZ 3 Manual de usuario

Adam Equipment

Adam Equipment MDW-250L Manual de usuario

Adam Equipment

Adam Equipment MDW-160M Manual de usuario

Adam Equipment

Adam Equipment HCB-J Jewellery Series Manual de usuario

Adam Equipment

Adam Equipment Warrior Series Manual de usuario

Adam Equipment

Adam Equipment HIGHLAND HCB 602M Manual de usuario

Adam Equipment

Adam Equipment AGB Series Manual de usuario

Adam Equipment

Adam Equipment QBW Series Manual de usuario

Adam Equipment

Adam Equipment PTS plus Series Manual de usuario

Adam Equipment

Adam Equipment MCW-250 L Manual de usuario

Adam Equipment

Adam Equipment HIGHLAND SERIES Manual de usuario

Adam Equipment

Adam Equipment CQT1752GR Manual de usuario

Adam Equipment

Adam Equipment PGL SERIES Manual de usuario

Adam Equipment

Adam Equipment MDW - 300L Manual de usuario

Adam Equipment

Adam Equipment MUW Manual de usuario

Adam Equipment

Adam Equipment CBC SERIES Manual de usuario

Adam Equipment

Adam Equipment CB Balance Manual de usuario

Adam Equipment

Adam Equipment PGL SERIES Manual de usuario

Adam Equipment

Adam Equipment CBC SERIES Manual de usuario

Adam Equipment

Adam Equipment CBK series Manual de usuario

Adam Equipment

Adam Equipment CFC SERIES Manual de usuario

Adam Equipment

Adam Equipment WBW 3M Manual de usuario

Adam Equipment

Adam Equipment AZextra 3 Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario