Adam Equipment MDW-160M Manual de usuario

Adam Equipment

MDW-160M

MECHANICAL PHYSICIAN SCALE

(P.N. 4283, Revision B2, December 2006)

CONTENTS

1. INTRODUCTION.................................................................................................3

2. SPECIFICATIONS..............................................................................................3

3. INSTALLATION...................................................................................................4

3.1 GENERAL INSTALLATION..........................................................................4

3.2 HEIGHT ROD INSTALLATION ....................................................................6

4. MEASURING HEIGHT........................................................................................6

5. WEIGHING OPERATION ...................................................................................8

1. INTRODUCTION

•The Medical Physician Scale MDW-160M can weigh a

person as well as measure the height.

•It is simple to use and can be moved around with the help of

the wheel attachment at the bottom of the scale.

•The MDW-160M scale is widely applicable for use in

business, schools, hospitals, clinics and sports departments.

•A height rod assembly is included as standard.

2. SPECIFICATIONS

MDW-160M

Capacity 160 kg / 350 lb.

Readability 100 g / 0.2 lb.

Platform Size 375 mm x 275 mm /

14.8” x 10.8”

Overall

dimension 530 mm x 275 mm x 1485 mm /

20.9” x 10.8” x 58.5”

Height

measurement Up to 210 cm / 84”

Division of height

measurement 0.5 cm / 0.2”

Gross weight 18 kg / 40 lb

3. INSTALLATION

3.1 GENERAL INSTALLATION

This precision instrument is extremely easy to set up, as all major parts

are factory pre-assembled.

Hardware supplied for installation:

−6 no. M6 x 12 screws

−6 no. M6 Lock washers

−2 no. Hex Head screws

−Tool (Spanner/Wrench)

1. Column with head

2. Height measuring rod

3. Platform base

4. Wheel attachment

NOTE: If the column bracket is bent, straighten it before assembling.

Slip the column over the column bracket on the base.

Hold the column straight so that the draft rod fits into the opening

aperture of the column bracket.

Fix the column to the column bracket using two M6 screws in front of the

column and four at the back.

Lay down the scale, with column horizontal to the floor.

Raise the draft rod keeping out of the lever’s way.

1. Column

2. Column bracket

3. Base

4. Hook at the end

of the Draft rod

5. Lever with pivot

6. M6 screws

Push the lever. When the lever is in position, hook the draft rod around

the pivot.

←An assembled view

3.2 HEIGHT ROD INSTALLATION

•Insert the two hexagonal headed screws from the hardware

pack into the holes in the front of the column and tighten

slightly.

•Place both the height rod clamping brackets over the two

pre-installed hexagonal headed screws and pull it down.

•Use the included wrench to tighten both the screws. Do not

over tighten the screws.

A. Latch to lock/unlock the

measuring arm

B. The measuring arm

C. The inner height rod

D. The outer height rod

E. Two height rod clamping brackets

for fixing the height rods assembly to

the column. One hexagonal headed

screw is required for each bracket.

4. MEASURING HEIGHT

Preparing the scale to measure the height-

•Before the person steps onto the scale platform, the

measuring arm should be lifted to the horizontal position, and

raised well above the person’s apparent height.

•The person may now step onto the scale platform.

•The measuring arm should be held horizontal and above the

person’s head and should not be released.

•Carefully lower the measuring arm, while keeping it

horizontal, until it rests gently upon the top of the person’s

head. If the person is shorter than 101.5 cm, push the latch

to the right, while simultaneously pushing down the

measuring arm until it rests horizontally upon the top of the

person’s head.

Read the height of the person as follows:

•The rear end of the measuring arm is tapered to point at the

reading on the height rods.

•If the tapered end of the measuring arm points at the outer

height rod, then the height of the person is same as the

reading at this point on the outer height rod.

•If the tapered end of the measuring arm points at the inner

height rod, then the correct height of the person is same as

the reading shown on the inner height rod where both the

height rod meets, i.e., read at the top of the outer height rod

(Just above the “Read” arrow marked on the outer height

rod).

•While holding the measuring arm horizontally, raise the arm

above the person’s head. The person may now step off the

scale platform. Hold the arm horizontal until the person is

clear of the height rod.

•Fold the measuring arm back to the vertical position and

adjust the height rod back to the rest position (i.e. the

measuring arm should be locked in place within the inner

height rod and the inner rod should be at its lowest position).

5. WEIGHING OPERATION

To do the zero setting-

•For accurate weighing, place the scale on a levelled floor.

•Move both the balancing masses to zero when the scale

platform is empty.

•If the scale is balanced, the lever will be in the horizontal

position. This will be indicated by the arrow indicator being in

line with the horizontal mark on the right side of the column

head.

•It may be necessary to turn the zero-setting screw to the

right or left until the scale balances.

Otros manuales para MDW-160M

Tabla de contenidos

Otros manuales de Escala de Adam Equipment

Adam Equipment

Adam Equipment SHS Series Manual de usuario

Adam Equipment

Adam Equipment CBC SERIES Manual de usuario

Adam Equipment

Adam Equipment CQT 202 Instrucciones de montaje

Adam Equipment

Adam Equipment CBC SERIES Manual de usuario

Adam Equipment

Adam Equipment IHS Series Manual de usuario

Adam Equipment

Adam Equipment AQT Series Manual de usuario

Adam Equipment

Adam Equipment CBC-M Series Manual de usuario

Adam Equipment

Adam Equipment MDW-250L Manual de usuario

Adam Equipment

Adam Equipment MDW Manual de usuario

Adam Equipment

Adam Equipment AZextra 3 Manual de usuario

Adam Equipment

Adam Equipment MCW-250 L Manual de usuario

Adam Equipment

Adam Equipment CBW Series Manual de usuario

Adam Equipment

Adam Equipment MTB Manual de usuario

Adam Equipment

Adam Equipment ECLIPSE Manual de usuario

Adam Equipment

Adam Equipment Nimbus NBL Serie Manual de usuario

Adam Equipment

Adam Equipment LBX 12 Manual de usuario

Adam Equipment

Adam Equipment CORE SERIES Manual de usuario

Adam Equipment

Adam Equipment Luna LAB Series Manual de usuario

Adam Equipment

Adam Equipment CPWplus 6 Manual de usuario

Adam Equipment

Adam Equipment Gladiator GGS 8 Manual de usuario

Adam Equipment

Adam Equipment ABK Series Manual de usuario

Adam Equipment

Adam Equipment HCB-J Jewellery Series Manual de usuario

Adam Equipment

Adam Equipment WBZ 3 Manual de usuario

Adam Equipment

Adam Equipment PGL SERIES Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario