Adam Equipment MDW - 250L Manual de usuario

Adam Equipment

MDW – 250L

DIGITAL PHYSICIAN SCALE

Software EMW-250L-20080601

ADAM EQUIPMENT CO. LTD.

p.n. 4302, Rev. C4, November 2009

CONTENTS

1.0 INTRODUCTION ..........................................................................................4

2.0 TECHNICAL SPECIFICATIONS...................................................................4

3.0 DISPLAY AND KEY DESCRIPTIONS ..........................................................5

4.0 SETTING UP THE SCALE............................................................................6

5.0 FUNCTION ...................................................................................................5

5.1 WEIGHING................................................................................................5

5.2 MEASURING HEIGHT..............................................................................6

6.0 CALIBRATION ..............................................................................................6

7.0 USER PARAMETERS ..................................................................................8

8.0 RS232 COMMUNICATIONS.........................................................................9

9.0 ERROR MESSAGES..................................................................................13

10.0 WARNING...................................................................................................13

1.0 INTRODUCTION

•The MDW 250L scale is a Digital Physician Scale.

•It is an accurate electronic device with advanced design and stable

performance.

•It is designed to measure both the weight and the height of a person.

2.0 TECHNICAL SPECIFICATIONS

Maximum capacity 250 kg / 550lb

Minimum capacity 2 kg / 4lb

Scale division 0.1Kg / 0.2lb

Height range 80 cm-210 cm

Division of measurement 0.5 cm

Display LED display

Size of platform 375 X 275 mm

Overall dimension 535 X 275 X 1040 mm

Deadweight 13 kg

Environment for Use Temperature: 5ºC-40ºC;

Humidity: <85℅RH

Power 12vAC 500mA adapter

Battery Internal, re-chargeable

6V 4Ah, 5 hours approx.

Calibration External calibration through the keypad.

Communications Bi-directional RS232

3.0 DISPLAY AND KEY DESCRIPTIONS

KEYS FUNCTIONS

[On / Off

/Zero]

To turn the scale on or off.

To zero the scale if the display drifts from zero.

[Tare] To tare the scale, if necessary.

[Units] To toggle the weighing unit between Kg and Lb.

[Print /

Hold]

To lock the reading even if the person to be weighed is moving and

also to print the weight details out.

DISPLAY DESCRIPTIONS

Kg Indicates when the scale is weighing in Kilograms.

Lb Indicates when the scale is weighing in Pounds.

Hold Indicates when the scale has held the weight reading shown on the

display. It will flash until it locks into the stable reading when it will

then remain on constantly when it has held the displayed reading.

When the battery is low, this symbol will be light up. Connect the

adapter to recharge the battery.

CH The charge light will be on when the battery is recharging.

This indicates when the scale is being used with the AC adapter.

ZERO This indicator will be displayed in the left corner when the scale

reaches zero.

NET The Net weight is displayed, Tare weight is at zero.

4.0 SETTING UP THE SCALE

•Take the Physician scale out of the box.

•Unwind the load cell cable (number 2 on the diagram).

•Run the cable up through the pillar from the base of the scale.

•Use the 4 screws (number 3 on the diagram) to mount the pillar to the

indicator.

•Connector the plug and socket (number 6 and 7 on the diagram) and

insert the pole into the pole holder.

•Secure the pole to the pole holder by inserting the 2 screws (number 9

on the diagram).

•Secure the height rod into the height rod holder (number 4 and 8 on the

diagram).

height rod

holder

height rod

cable to

indicator

platform

pole

screw

socket

plug

5.0 FUNCTION

5.1 WEIGHING

•Place the Physician Scale on an even floor and press the [On/Off] key.

•The instrument performs a self-test after which it is ready for operation.

•Press the [On/Off] key and the machine switches off.

•The person to be weighed can step on to the platform once the scale

shows 0.0 on the display. The weight will be display in Kg. or lb.

depending on the units chosen by the user.

•If the weighing value is to be tared press the tare key to remove the

weight value from the display.

•Press the [Units] key for changing the weighing unit to kg or lb. The

LED will indicate the chosen weighing unit.

•Overload display: When “

FULL

” appears on the display, it shows that

the load on the platform is over the maximum capacity. Under these

circumstances, it is necessary to reduce the load otherwise the sensor

or the platform will be damaged.

•Hold Function: To lock the weighing result, press the [Print/Hold]

key. The LED will flash until a stable reading has been obtained and

then it will light up constantly. To release the function, press the

[Print/Hold] key again.

•Print Function: To send the weighing result to a printer or computer

press the [Print/Hold] key when the [Print/Hold] key has been set up

in the parameter section to work as print function.

(Print function is only applied for scale with RS232 interface)

5.2 MEASURING HEIGHT

•While measuring the height, it is necessary to pull up the measuring

board at a right angle with the inside tube.

•When the tube is pulled out straight, it is sufficient to measure the

height form 80-136cm. The number can be obtained upon the conjoint

place where the upper part of middle tube screw meets with the inside

tube scale.

•Further, if the middle tube is pulled out straight, it is possible to

measure the height from 136-210cm. The reading can be obtained at

the conjoint place where the upper part of outside tube screw meets

with the middle tube scale.

6.0 CALIBRATION

Before calibrating the scale, you should ensure that you have a known weight for

calibration.

1. When in normal weighing mode with the scale at zero press and hold down

[TARE] and [ON / OFF] keys to enter the calibration mode.

2. If the calibration switch is in the off position on the main PCB inside the scale, the

indicator will show ‘CAL.OFF” and then exit this mode. If the indicator shows”

CAL-?”, the scale is ready for calibration, showing the calibration switch is in the

on position. If the calibration switch is in the Off position open up the indicator

and move the switch to the On position. See diagram on page 8.

3. When the indicator shows ” CAL-?”, press the [TARE] key to confirm and go to

next step, or press the [ON / OFF] key to exit the calibration mode.

4. When ‘0.0’ is displayed the scale will begin to calibrate the scale’s zero-point.

Ensure that there is no load or weight on the scale’s platform . Press the [TARE]

key to confirm, or press the [ON / OFF] key to exit this mode.

5. A few seconds after the [TARE] key has been pressed in step 4 the scale will

show ‘250.0kg’ or ’500.0lb’ depending on which unit you chosen, this is the

default calibration weight from the factory. Press the [UNIT] key to select the

calibration weight unit that you want to calibrate in. Press the [ON / OFF] key to

exit the calibration mode at this point or press the [Print/Hold] key to choose a

different calibration weight value (50kg, 100kg, 150kg, 200kg, 250kg or 100lb,

200lb, 300lb, 400lb, 500lb); Then put on the weight that you selected and press

the [TARE] key to confirm the chosen standard weight that was selected earlier.

The displayed data will flash on the display and if the scale accepts the

calibration data it will calculate and store the information into the EEPROM. If an

error has occurred, the scale will display “CAL. Er” and return back to step 4 for

re-calibration. If the loaded weight is not within the range of 95% to 105% of the

weight value you selected, the scale will not calibrate but display “CAL. Er” and

return back to step 4 for re-calibration. )

6. Check the calibration by putting the weight that you calibrated at back on the

scale, if it is off repeat the calibration process again.

Tabla de contenidos

Otros manuales de Escala de Adam Equipment

Adam Equipment

Adam Equipment CBC SERIES Manual de usuario

Adam Equipment

Adam Equipment Luna LAB Series Manual de usuario

Adam Equipment

Adam Equipment LHS Series Manual de usuario

Adam Equipment

Adam Equipment CBW Series Manual de usuario

Adam Equipment

Adam Equipment CFC SERIES Manual de usuario

Adam Equipment

Adam Equipment HIGHLAND HCB123 Manual de usuario

Adam Equipment

Adam Equipment DUNE SERIES Manual de usuario

Adam Equipment

Adam Equipment SHS Series Manual de usuario

Adam Equipment

Adam Equipment NETS Hoja de información del producto

Adam Equipment

Adam Equipment CBD 100a Manual de usuario

Adam Equipment

Adam Equipment WBW Series Cómo utilizar

Adam Equipment

Adam Equipment PGL SERIES Manual de usuario

Adam Equipment

Adam Equipment WSK 8 Manual de usuario

Adam Equipment

Adam Equipment ASC Manual de usuario

Adam Equipment

Adam Equipment MTB Manual de usuario

Adam Equipment

Adam Equipment CQT1751GR Manual de usuario

Adam Equipment

Adam Equipment Warrior Series Manual de usuario

Adam Equipment

Adam Equipment CBC SERIES Manual de usuario

Adam Equipment

Adam Equipment CQT1752GR Manual de usuario

Adam Equipment

Adam Equipment CBK series Manual de usuario

Adam Equipment

Adam Equipment CFC SERIES Manual de usuario

Adam Equipment

Adam Equipment AZextra 3 Manual de usuario

Adam Equipment

Adam Equipment CPWplus 6 Manual de usuario

Adam Equipment

Adam Equipment QBW Series Manual de usuario

Manuales populares de Escala de otras marcas

AWS

AWS ZEO-50 Manual de usuario

Gima

Gima Glass Body Fat Analyzer Manual de lista de piezas

Seca

Seca 374 Manual de usuario

TEC

TEC TEC SL59 SERIES Manual de usuario

Axis

Axis B/E Series Manual de usuario

Alecto

Alecto ACW-40 Manual de usuario

Rice Lake

Rice Lake MSI-4260 IS Manual de usuario

IKA

IKA RCT basic safety control Manual de usuario

ADE

ADE M20011 Manual de usuario

Duronic

Duronic KS3000 Manual de usuario

Digi

Digi SM-720 Manual de usuario

Cardinal

Cardinal CS Series Manual de usuario

Korona

Korona Kastella Manual de usuario

A&D

A&D FC-50Ki Manual de usuario

BDA

BDA CAMARGUE Manual de usuario

Tanita

Tanita HD-357 Manual de usuario

Leifheit

Leifheit 03173 Manual de usuario

Lumme

Lumme LU-1340 Manual de usuario