ADA INSTRUMENTS CUBE MINI GREEN Manual de usuario
Line Laser
OPERATING MANUAL
CUBE MINI GREEN
adainstruments.com
2English
1
2
3 4
5
42
1
3
3
THE MANUFACTURE RESERVES THE RIGHT TO MAKE CHANGES (NOT
HAVING AN IMPACT ON THE SPECIFICATIONS) TO THE DESIGN,
COMPLETE SET WITHOUT GIVING PRIOR WARNING.
APPLICATION
Line Laser ADA CUBE MINI GREEN is designed to check the horizontal and
vertical position of the surfaces of the elements of building structures and
also to transfer the angle of inclination of the structural part to similar
parts during construction and installation works.
SPECIFICATIONS
Leveling Range................................... self-leveling, ±3°
Accuracy.............................................. ±2mm/10m
Working range with /
without detector............................... 70 m / 20 m
Power Supply...................................... 2xAA Batteries Alkaline
Operation time................................... Approx. 15 hours
Laser Source, laser class.................. 1x520nm, 2
Tripod thread...................................... 1/4”
Operating temperature.................... -10°C +45°C
Dimensions.......................................... 65х65х45 mm
Weight................................................... 190g
LASER LINES
FEATURES
1. laser emitting window
2. battery cover
3. compensator switch
4. tripod mount 1/4”
English
1
2
4English
CHANGE OF BATTERIES
Open battery compartment. Insert batteries. Take care to correct polarity.
Close battery compartment. ATTENTION: If you are not going to use instru-
ment for a long time, take out batteries.
OPERATION
Place the line laser on the working surface or mount it on the tripod/pillar
or wall mount (comes with the instrument). Switch on the line laser: turn
the compensator switch (3) to the position “ON”. When enabled, the ver-
tical and horizontal plane projected constantly. Visual alarm (blinking line)
indicates that the device was not installed within the compensation range
± 3 º. To properly work align the unit in a horizontal plane.
TO CHECK THE ACCURACY OF LINE LASER (SLOPE OF PLANE)
Set up the line laser between two walls, the distance is 5m.Turn on the Line
Laser and mark the point of cross laser line on the wall. Set up the instru-
ment 0,5-0,7m away from the wall and make, as described above, the same
masrks. If the dierence {a1-b2} and {b1-b2} is less then the value of “ac-
curacy” (see spesications), there is no need in calibration. Example: when
you check the accuracy of Cross Line Laser the dierence is {a1-a2}=5 mm
and {b1-b2}=7 mm. The instrument’s error: {b1-b2}-{a1-a2}=7-5=2 mm.
Now you can compare this error with standard error.
If the accuracy of Line Laser isn’t corresponding with claimed accuracy,
contact the authorized service center.
TO CHECK THE ACCURACY OF HORIZONTAL BEAM
Choose a wall and set laser 5M away from the wall. Turn on the laser and
cross laser line is marked A on the wall. Find another point M on the hori-
zontal line, the distance is around 2.5m. Swivel the laser, and another cross
3
5
point of cross laser line is marked B. Please note the distance of B to A
should be 5m. Measure the distance between M to cross laser lune, if the
dierence is over 3mm, the laser is out of calibration, please contact with
seller to calibrate the laser.
TO CHECK PLUMB
Choose a wall and set laser 5m away from the wall. Mark point A on the
wall, please note the distance from point A to ground should be 3m. Hang
a plumb line from A point to ground and nd a plumb point B on ground.
turn on the laser and make the vertical laser line meet the point B, along
the vertical laser line on the wall and measure the distance 3m from point
B to another point C. Point C must be on the vertical laser line, it means the
height of C point is 3m.
Measure the distance from point A to point C, if the distance is over 2 mm,
please, contact with seller to calibrate the laser.
PRODUCT LIFE
Product life of the tool is 7 years. The battery and the tool should never
be placed in municipal waste. Date of production, manufacturer’s contact
information, country of origin are indicated on the product sticker.
CARE AND CLEANING
Please handle line laser with care. Clean with soft cloth only after any use.
If necessary damp cloth with some water. If instrument is wet clean and
dry it carefully. Pack it up only if it is perfectly dry. Transport in original
container/case only.
Note: During transport On/O compensator lock (3) must be set to posi-
tion “OFF”. Disregard may lead to damage of compensator.
SPECIFIC REASONS FOR ERRONEOUS MEASURING RESULTS
• Measurements through glass or plastic windows;
English
6English
• Dirty laser emitting window;
• After line laser has been dropped or hit. Please check the accuracy;
• Large uctuation of temperature: if instrument will beused in cold areas
after it has been stored in warm areas (or the other way round) please wait
some minutes before carrying out measurements.
ELECTROMAGNETIC ACCEPTABILITY (EMC)
• It cannot be completely excluded that this instrument will disturb other
instruments (e.g. navigation systems);
• will be disturbed by other instruments (e.g. intensive electromagnetic ra-
diation nearby industrial facilities or radio transmitters).
LASER CLASS 2 WARNING LABEL ON THE LINE LASER
LASER CLASSIFICATION
The instrument is a laser class 2 laser product accortding to DIN IEC 60825-
1:2014 and Class II in accordance with CFR 21 § 1040 (FDA). This tool may
be used without need for further protective measures.
SAFETY INSTRUCTIONS
• Please follow up instructions given in operators’ manual.
• Do not stare into beam. Laser beam can lead to eye injury (even from
greater distances).
• Do not aim laser beam at persons or animals. The laser plane should
be set up above eye level of persons. Use the instrument for measuring
jobs only.
• Do not open instrument housing. Repairs should be carried out by au-
thorized workshops only. Please contact your local dealer.
• Do not remove warning labels or safety instructions.
• Keep instrument away from children.
• Do not use instrument in explosive environment.
5
7English
WARRANTY
This product is warranted by the manufacturer to the original purchaser to
be free from defects in material and workmanship under normal use for a
period of two (2) years from the date of purchase. During the warranty pe-
riod, and upon proof of purchase, the product will be repaired or replaced
(with the same or similar model at manufactures option), without charge
for either parts of labour. In case of a defect please contact the dealer
where you originally purchased this product. The warranty will not apply
to this product if it has been misused, abused or altered. Without limiting
the foregoing, leakage of the battery, bending or dropping the unit are
presumed to be defects resulting from misuse or abuse.
EXCEPTIONS FROM RESPONSIBILITY
The user of this product is expected to follow the instructions given in op-
erators’ manual. Although all instruments left our warehouse in perfect
condition and adjustment the user is expected to carry out periodic checks
of the product’s accuracy and general performance. The manufacturer,
or its representatives, assumes no responsibility of results of a faulty or
intentional usage or misuse including any direct, indirect, consequential
damage, and loss of prots. The manufacturer, or its representatives, as-
sumes no responsibility for consequential damage, and loss of prots by
any disaster (earthquake, storm, ood ...), re, accident, or an act of a third
party and/or a usage in other than usual conditions.
The manufacturer, or its representatives, assumes no responsibility for
any damage, and loss of prots due to a change of data, loss of data and
interruption of business etc., caused by using the product or an unusable
product. The manufacturer, or its representatives, assumes no responsi-
bility for any damage, and loss of prots caused by usage other thsn ex-
plained in the users’ manual.
The manufacturer, or its representatives, assumes no responsibility for
damage caused by wrong movement or action due to connecting with oth-
er products.
8English
WARRANTY DOESN’T EXTEND TO FOLLOWING CASES:
1. If the standard or serial product number will be changed, erased, re-
moved or wil be unreadable.
2. Periodic maintenance, repair or changing parts as a result of their nor-
mal runout.
3. All adaptations and modications with the purpose of improvement
and expansion of normal sphere of product application, mentioned in the
service instruction, without tentative written agreement of the expert pro-
vider.
4. Service by anyone other than an authorized service center.
5. Damage to products or parts caused by misuse, including, without lim-
itation, misapplication or nrgligence of the terms of service instruction.
6. Power supply units, chargers, accessories, wearing parts.
7. Products, damaged from mishandling, faulty adjustment, maintenance
with low-quality and non-standard materials, presence of any liquids and
foreign objects inside the product.
8. Acts of God and/or actions of third persons.
9. In case of unwarranted repair till the end of warranty period because
of damages during the operation of the product, it’s transportation and
storing, warranty doesn’t resume.
9
English
WARRANTY CARD
Name and model of the product __________________________________________
Serial number___________________________Date of sale______________________
Name of commercial organization ________________________________________
stamp of commercial organization
Warranty period for the instrument explotation is 24 months after the
date of original retail purchase.
During this warranty period the owner of the product has the right for
free repair of his instrument in case of manufacturing defects.
Warranty is valid only with original warranty card, fully and clear lled
(stamp or mark of thr seller is obligatory).
Technical examination of instruments for fault identication which is
under the warranty, is made only in the authorized service center.
In no event shall manufacturer be liable before the client for direct or
consequential damages, loss of prot or any other damage which occur
in the result of the instrument outage.
The product is received in the state of operability, without any visible
damages, in full completeness. It is tested in my presence. I have no
complaints to the product quality. I am familiar with the conditions of
qarranty service and i agree.
purchaser signature _______________________________
Before operating you should read service instruction!
If you have any questions about the warranty service and technical support contact
seller of this product
10 Russian
1
2
3 4
5
42
1
3
Tabla de contenidos
Idiomas:
Otros manuales de Nivel láser de ADA INSTRUMENTS
ADA INSTRUMENTS
ADA INSTRUMENTS ProLevel 40 Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS LASERTANK 3-360 GREEN Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE 360-2V GREEN Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS 6D SERVOLINER GREEN Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS ARMO 2D Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS 2D Basic Level Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS 6D SERVOLINER Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE 3D Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS ProDigit 30 Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE MINI Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS 3D Liner 2V Green Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS ROTARY 500 HV SERVO Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS ROTARY 400 HV Servo Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS ROTARY 500 HV SERVO Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS ROTARY 400 HV Servo Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS ProDigit Mini Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS CUBE 2-360 Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS ProDigit 30 Manual de usuario
ADA INSTRUMENTS
ADA INSTRUMENTS TOPLINER 3-360 GREEN Manual de usuario
