ACME Stage Panel 1080 Manual de usuario

User Manual

Please read the instruc on carefully before use

LP-1080

CONTENTS

1. Safety Instruction.............................................................................................................................2

2. Technical Specification....................................................................................................................3

3. How To Set The Unit .......................................................................................................................4

3.1 Control panel..............................................................................................................................4

3.2 Main Function............................................................................................................................5

4. How To Control The Unit..............................................................................................................10

4.1 Master/Slave Function.............................................................................................................10

4.2 DMX Controller.......................................................................................................................10

5. DMX512 Configuration.................................................................................................................11

6. DMX512 Connection.....................................................................................................................13

7. Troubleshooting .............................................................................................................................14

8. Fixture Cleaning.............................................................................................................................15

1. Safety Instruction

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure

that they also receive this instruction booklet.

Unpack and check carefully there is no transportation damage before using the unit.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

The unit is for indoor use only. Use only in a dry location.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces. Be sure that no ventilation slots are blocked.

Disconnect main power before replacement or servicing.

Make sure there are no flammable materials close to the unit while operating as it is fire hazard.

Use safety cable when fixes this unit. DO NOT handle the unit by taking its head only, but always

by taking its base.

Maximum ambient temperature is Ta: 40℃. DO NOT operate it where the temperature is higher

than this.

Unit surface temperature may reach up to 85℃. DO NOT touch the housing bare-hand during its

operation. Turn off the power and allow about 15 minutes for the unit to cool down before

replacing or serving.

In the event of serious operating problem, stop using the unit immediately. Never try to repair the

unit by yourself. Repairs carried out by unskilled people can lead to damage or malfunction.

Please contact the nearest authorized technical assistance center. Always use the same type spare

parts.

DO NOT touch any wire during operation as high voltage might be causing electric shock.

Please read carefully this instruction, which includes important

information about the installation, usage and maintenance.

Warning:

To prevent or reduce the risk of electrical shock or fire, do not expose the unit to rain or moisture.

DO NOT open the unit within five minutes after switching off.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

Caution:

There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs

yourself. In the unlikely event your unit may require service, please contact your nearest dealer.

Installation:

The unit should be mounted via its screw holes on the bracket. Always ensure that the unit is

firmly fixed to avoid vibration and slipping while operating. And make sure that the structure to

which you are attaching the unit is secure and is able to support a weight of 10 times of the unit’s

weight. Also always use a safety cable that can hold 12 times of the weight of the unit when

installing the fixture.

The equipment must be fixed by the professionals. And it must be fixed at a place where is out of

the touch of people and has no one pass by or under it.

2. Technical Specification

- DMX Control: 1/3/4/4/4/4/6 Channels Mode

- Smooth 0~100% dimming and variable strobe speeds

- Three Operation Modes: DMX, Master/Slave, Sound Active

- The DMX Address code can be set by the DMX tester CA-T

- Variable strobe effects

- Beam Angle: 135°

If using a 230V 50Hz power supply, DO NOT connect in series more than 3 units; use

another main supply for the next 3 fixtures.

If using a 120V 60Hz power supply, DO NOT connect in series more than 2 units; use

another main supply for the next 2 fixtures.

Voltage

：

AC 100-240V, 50/60Hz

Power Consumption

：

247W

LED: 1080pcs SMD RGB(Tri-color) LEDs

Fuse: T 6.3A

Dimension

：

515 x 225 x 142mm

Weight

：

8.9Kgs

3. How To Set The Unit

3.1 Control panel

○

1E A Display: To show the various menus and the selected functions

A○

2E A Indicator LED:

DMX

DMX input present

MASTER

Master Mode

SLAVE On Slave Mode

SOUND Flashing Sound activation

A○

3E A Button:

MENU To select the programming functions

DOWN To go backward in the selected functions

UP To go forward in the selected functions

ENTER To confirm the selected functions

A○

4E A Fuse(T 6.3A): Protect the fixture from the damage of over-current.

A○

5E A Microphone: To receive music for the sound active.

A○

6E A Mains output: Connect to supply mains power for the next fixture.

A○

7E A Mains input: Connect to supply mains power

A○

8E A DMX input: For DMX512 link, use 3/5-pin XLR plug cable to input DMX signal

A○

9E A DMX output: For DMX512 link, use 3/5-pin XLR plug cable to link the next fixture.

A○

10EASafety Ring: Keep the installation safe.

3.2 Main Function

To select any of the given functions, press the MENU button up to when the required one is

showing on the display. Select the function by ENTERbutton and the display will blink. Use

DOWN and UP button to change the mode. Once the required mode has been selected, press the

ENTER button to setup, to go back to the functions without any change press the MENU button

again. Hold and press the MENU button about one second or wait for one minute to exit the menu

mode.

The main functions are showing below:

DMX 512 Address Setting

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to change the DMX 512Address. Once

the address has been selected, press the ENTER button to setup or automatically exit menu mode

without any change after 8 seconds. Back to the previous functions without any change press the

MENU button.

Channel Mode

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select (mode 1) or

(mode 2)… (mode 7), Once the mode has been selected, press theENTER button to setup or

automatically exit menu mode without any change after 8 seconds. Back to the previous functions

without any change press the MENU button.

Show Mode

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select (show 0), (show

1)… (show 8) or (Fade). Press either ...or , , you can adjust the

speed from (the slowest) to (the fastest). Once the mode has been selected, press the

ENTER button to setup or automatically exit menu mode without any change after 8 seconds. Back

to the previous functions without any change press the MENU button.

Slave Mode

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select (master), (slave

1) …or (slave 4). Once the mode has been selected, press the ENTER button to setup or

automatically exit menu mode without any change after 8 seconds. Back to the previous functions

without any change press the MENU button.

Color Mode

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select (Color Jump) or

(Color Fade). Once selected, press the ENTER button to setup or automatically exit menu mode

without any change after 8 seconds. Back to the previous functions without any change press the

MENU button.

Sound Mode

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select or . Once the

mode has been selected, press the ENTER button to setup or automatically exit menu mode

without any change after 8 seconds. Back to the previous functions without any change press the

MENU button.

Blackout Mode

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select (black out) or

(normal). Once selected, press the ENTER button to setup or automatically exit menu mode

without any change after 8 seconds. Back to the previous functions without any change press the

MENU button.

Color Setup

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select , (color

1)… (color 16), when you have selected the button and press the ENTER button,

you can use the DOWN and the UP button select the (red), (green), (blue)

and you can adjust the intensity from to . Back to the previous functions without any

change press the MENU button.

LED Display

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select (LED on) or

(LED off). Once selected, press the ENTER button to setup or automatically exit menu mode

without any change after 8 seconds. Back to the previous functions without any change press the

MENU button.

Display Inverse

Press the MENU button up until is shown on the display. Use the ENTER button to select

(normal) or (inverse). Back to the previous functions without any change press the

MENU button.

Temperature

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the unit will show the temperature. Back to the previous functions without any change press the

MENU button.

White Balance

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will blink. Use the DOWN and the UP button to select , or .

Once selected, press the ENTER button to adjust the value (125~255), or automatically exit menu

mode without any change after 8 seconds. Back to the previous functions without any change press

the MENU button.

Fixture Hours

Press the MENU button up until is shown on the display. Pressing the ENTER button and

the display will show the number of working hours of the unit. Back to the previous functions

without any change press the MENU button.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Equipo de DJ de ACME

ACME

ACME XP-470 BSW Manual de usuario

ACME

ACME LED-920D Manual de usuario

ACME

ACME MINI ELLIPSOIDAL 10 Manual de usuario

ACME

ACME GENESIS COLOR II Manual de usuario

ACME

ACME SAM-50 Manual de usuario

ACME

ACME LED WAVE 100 Manual de usuario

ACME

ACME PAGEANT 300ZR Manual de usuario

ACME

ACME LED-Exercet Manual de usuario

ACME

ACME CP-21TC Manual de usuario

ACME

ACME SPLENDOR 90 Manual de usuario

ACME

ACME CYC-200 FC Manual de usuario

ACME

ACME Theatre LED Colour Flood Manual de usuario

ACME

ACME Dragonfly Quad Manual de usuario

ACME

ACME LED-7871 Manual de usuario

ACME

ACME XP-1200F Manual de usuario

ACME

ACME Stage Blinder P4 Manual de usuario

ACME

ACME LED-245 II Manual de usuario

ACME

ACME WHACK XP-231 BEAM Manual de usuario

ACME

ACME FURY LED RGB Manual de usuario

ACME

ACME IM-5S-ELC Manual de usuario

ACME

ACME ORION XP-260 BEAM Manual de usuario

ACME

ACME E-40D TC DXX Manual de usuario

ACME

ACME CW-108 Manual de usuario

ACME

ACME LED-737 Manual de usuario

Manuales populares de Equipo de DJ de otras marcas

ALPHA LITE

ALPHA LITE ALPHA 1500 Manual del propietario

Chauvet

Chauvet OVATION E-930VW Manual de usuario

Zumtobel

Zumtobel APHRODITE Home Manual de usuario

Snow Masters

Snow Masters Zig Oscillator Manual de usuario

EuroLite

EuroLite 50530554 Manual de usuario

Beamz

Beamz BUV243 Manual de usuario

thomann

thomann Stairville DJ Lase 40-G MK-III Manual de usuario

Eagletone

Eagletone 6 Eyes Flower Manual de usuario

EuroLite

EuroLite FLD-1508 Manual de usuario

Technical Pro

Technical Pro LG8xSEA Manual de usuario

JB Systems

JB Systems Lounge Laser DMX Manual de usuario

Lightmaxx

Lightmaxx Vega Halo 90 Manual de usuario

Elation

Elation FUZE WASH Z350 Manual de usuario

Maverick

Maverick MK3 WASH Manual de usuario

Infinity

Infinity TF-260C7 Fresnel Manual de usuario

Chauvet

Chauvet EVE E-50Z Manual de usuario

Eliminator Lighting

Eliminator Lighting E 138 Manual de usuario

EuroLite

EuroLite Mini Multicolor LED Flashing Light SC Manual de usuario