4IPNET OWL630 Manual de usuario
OWL630 V1.00
Outdoor Access Point
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
i
Copyright Notice
This document is protected by USA copyright laws and other laws. Besides, the
document is the property of 4IPNET, INC. You may not copy, reproduce, distribute,
publish, display, perform, or modify any part of this publication in any form or by any
means without prior written permission from 4IPNET, INC. You may not alter or remove any
copyright or other notice from copies of the content. All other brand and product names
are claimed or registered marks of their respective companies or organizations.
All rights reserved.
To download up-to-date version, please visit www.4ipnet.com.
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
ii
FCC CAUTION
This equipment has been tested and proven to comply with the limits for a class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
---Reorient or relocate the receiving antenna.
---Increase the separation between the equipment and receiver.
---Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
---Consult the dealer or an experienced radio/TV technician for help.
The device contains a low power transmitter which will send out Radio Frequency (RF) signal when
transmitting. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
iii
CE CAUTION
Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for
European Community, Switzerland, Norway, Iceland, and Liechtenstein
Model: OWL630
For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and
hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.
• Radio: EN 300.328:
• Radio: EN 50392
• EMC: EN 301.489-1, EN 301.489-17,
• EMC: EN 55022Class B, EN 55024:+ A1 + A2including the followings:
EN 61000-3-2, EN 61000-3-3.
EN 61000-4-2, EN 61000-4-3, EN 61000-4-4,
EN 61000-4-5, EN 61000-4-6, EN 61000-4-11
• Safety: EN 60950-1 + A11,
Caution:
This declaration is only valid for configurations (combinations of software, firmware, and hardware)
provided and supported by 4ipnet Inc. The use of software or firmware not provided and supported by
4ipnet Inc. may result in the equipment no longer being compliant with the regulatory requirements.
European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range
2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be
restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory
authority for compliance.
Taiwan NCC Statement
根據 NCC 低功率電波輻射性電機管理辦法 規定:
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或
變更原設計之特性及功能。
第十四條
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時應立即停用，並改善至
無干擾時方得繼續使用。
前項合法通信，指依電信法規定作業之無線電通信。
低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之擾。
在5.25 ~ 5.35 秭赫頻帶內操作之無線資訊傳輸設備，限於室內使用。
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
1
Preface
Package Contents
The OWL630 is a rugged multi-mode, high-end dual
radio 802.11 b/g/n + ac MIMO Access Point (AP),
specifically designed for building municipal or
campus wide wireless networks in harsh outdoor
environments. There are two system modes that
can be used for dual purposes. It can be deployed
as a traditional multi-wireless Access Point (AP) or a
Relay. The OWL630 access points make wireless
communication fast, secure and easy.
The die-cast Aluminum sealed OWL630 is rust-free
and IP68 compliant. It is high wind load resilient and
is designed to operate in a wide range of
temperature. Flexible deployment with a variety of
antennas allows OWL630 to easily serve clients
located in different directions as well as for
coverage extension.
This Quick Installation Guide (including FAQ
Instruction Guide) provides instructions for getting
started with the OWLAccess Point.
1. 4ipnet OWL630 x 1
2. Quick Installation Guide (QIG) x 1
3. Power Sourcing Equipment (PSE) X 1
(Optional)
4. Mounting Kit x 1
5. Ground Cable x 1
6. Waterproof M12 Connector Pack x 1
7. Waterproof RJ45 Connector Pack x 2
It is recommended to keep the original
packing material for possible future shipment
when repair or maintenance is required. Any
returned product should be packed in its
original packaging to prevent damage during
delivery.
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
2
System Overview
OWL630
Top
Back
N-type Connector x 6
For connecting to an antenna (RF Card A x 3, RF Card B x 3)
Connector marked –1 is for the primary antenna when theAP is not in 802.11n
or 802.11ac mode. Utilize all connectors for optimized MIMO performance.
Ground Connector
For connecting the ground wire
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
3
Bottom
1
M12 DC Connector
DC input (12V) is supported on OWL630
2
Ventilation Valve
Due to extreme weather conditions, water vapor in the OWL630 may
condense. The valve allows ventilation to prevent moisture buildup within
the OWL630.
3
Uplink (PoE Connector)
For connecting to the Power Sourcing Equipment (PSE)
4
Ethernet LAN
Attach Ethernet cables here for connecting to the wired local network
5
Console
The system can be configured via a serial console port. The administrator
can use a terminal emulation program such as Microsoft’s Hyper Terminal
for troubleshooting purposes.
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
4
Hardware Installation
The following are the basic installation steps which can be used for testing and configuring the OWL630.
Installation Steps:
Step 1. Connect an antenna to the connector.
Step 2. Connect the Ethernet Port of OWL630 to the POWER & DATA OUT Port of the PSE.
Step 3. Connect one end of an Ethernet cable to the Data Port of PSE and the other end to the computer.
Step 4. Power on the PSE in order to supply power to the OWL630.
Installing the Waterproof Connection Pack:
A connector pack as shown in the figure below is included with the system.
Parts Included: 5 Parts –Part-A ~ Part-E
Step 1. Take the white sticker off Part E and attach it to Part-D.
Step 2. Plug Part-C into Part-D. There will be three main parts as shown below.
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
5
Step 3. Insert the cable through the main parts and install a RJ-45 connector using straight-through method
(both ends are in the same wiring order: 1 (Tx+), 2 (Tx-), 3 (Rx+), 6 (Rx-)).
Example after the RJ-45 connector is installed,
Step 4. Plug the RJ-45 Connector into the system and make sure the locking ring is locked in well.
Step 5. Coil waterproof tape to secure the parts of the Waterproof Connector Pack.
Straight-Through Cable Wiring
Quick Installation Guide
OWL630 Enterprise Access Point ENGLISH
Copyright © 4IPNET, INC. All rights reserved.
6
Installing the Waterproof Connection Pack (Optional):
The M12 Waterproof Connector Pack is used for DC power supply, and it consists of 5 parts:
Step 1. Pass power cable through the Sealing Nut, Gaskets, and Clamp Ring (items 2-5)
Step 2. Solder power pins with reference to the pin definition below
Pin Number
Pin Definition
1
V+
3
V–
4
NC
Tabla de contenidos
Otros manuales de Punto de acceso inalámbrico de 4IPNET
4IPNET
4IPNET EAP706 Manual de usuario
4IPNET
4IPNET EAP210 Manual de usuario
4IPNET
4IPNET EAP220 Manual de usuario
4IPNET
4IPNET EAP210 Manual de usuario
4IPNET
4IPNET OWL530 Manual de usuario
4IPNET
4IPNET EAP760 Manual de usuario
4IPNET
4IPNET EAP727 Manual de usuario
4IPNET
4IPNET EAP750 V1.00 Manual de usuario
4IPNET
4IPNET EAP737 Manual de usuario
4IPNET
4IPNET EAP200 Manual de usuario
4IPNET
4IPNET EAP740 Manual de usuario
4IPNET
4IPNET OWL530 v1.00 Manual de usuario
4IPNET
4IPNET OWL800 Manual de usuario
4IPNET
4IPNET EAP200 Manual de usuario
4IPNET
4IPNET EAP320 V1.20 Manual de usuario
4IPNET
4IPNET EAP210 Manual de usuario
4IPNET
4IPNET EAP747 Manual de usuario
4IPNET
4IPNET OWL500 Manual de usuario
4IPNET
4IPNET EAP100 Manual de usuario
4IPNET
4IPNET OWL300 Manual de usuario
