4IPNET EAP110 Manual de usuario

EAP110 V1.10

Enterprise Access Point

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

This document is protected by U A copyright laws and other laws. Besides, the

document is the property of 4IPNET, INC. You may not copy, reproduce, distribute,

publish, display, perform, or modify any part of this publication in any form or by any

means without prior written permission from 4IPNET, INC. You may not alter or remove any

are claimed or registered marks of their respective companies or organizations.

To download up-to-date version, please visit www.4ipnet.com.

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

FCC CAUTION

This equipment has been tested and proven to comply with the limits for a class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

---Reorient or relocate the receiving antenna.

---Increase the separation between the equipment and receiver.

---Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

---Consult the dealer or an experienced radio/TV technician for help.

The device contains a low power transmitter which will send out Radio Frequency (RF) signal when

transmitting. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of 20 centimeters

between the radiator and your body.

You are cautioned that changes or modifications not expressly approved by the party responsible for

compliance could void your authority to operate the equipment.

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

CE CAUTION

Declaration of Conformity with Regard to the 1999/5/EC (R&TTE Directive) for

European Community, Switzerland, Norway, Iceland, and Liechtenstein

Model: EAP110

For 2.4 GHz radios, the device has been tested and passed the requirements of the following standards, and

hence fulfills the EMC and safety requirements of R&TTE Directive within the CE marking requirement.

• Radio: EN 300.328

• EMF: EN 50385:2002

• EMC: EN 301.489-1, EN 301.489-17

• Safety: EN 60950-1 + A11,

Caution:







This declaration is only valid for configurations (combinations of software, firmware, and hardware) provided

and supported by 4IPNET, Inc. The use of software or firmware not provided and supported by 4IPNET, Inc.

may result in the equipment no longer being compliant with the regulatory requirements.

European standards dictate maximum radiated transmit power of 100mW EIRP and frequency range

2.400-2.4835 GHz. This equipment is intended to be used in all EU and EFTA countries. Outdoor use may be

restricted to certain frequencies and/or may require a license for operation. Contact your local regulatory

authority for compliance.

Taiwan NCC Statement

根據 NCC 低功率電波輻射性電機管理辦法規定:

第十二條

經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或

變更原設計之特性及功能。

第十四條

低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時應立即停用，並改善至

無干擾時方得繼續使用。

前項合法通信，指依電信法規定作業之無線電通信。

低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之擾。

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

Preface Package Contents

4ipnet EAP110 is a high-end 802.11n/b/g 2.4GHz

MIMO Access Point (AP) with the best price/

performance for wireless connectivity in enterprise

and industrial applications and is compliant with the

latest industrial wireless security standards.

EAP110 makes the wireless communication fast,

secure and easy. It supports business grade

security such as IEEE802.1X, and Wi-Fi Protected

Access (WPA and WPA2).

EAP110 also features multiple ESSIDs with VLAN

tags and multiple Virtual APs; great for enterprise

applications, such as separating the traffics of

different departments using different ESSIDs. The

PoE LAN port can receive power from Power over

Ethernet (PoE) sourcing device. Its metal case is

IP50 anti-dust compliant, which means that EAP110

is well suited to WLAN deployment in industrial

environments.

This Quick Installation Guide provides instructions

and reference materials for getting started with

4ipnet EAP110.

1. 4ipnet EAP110 x 1

2. Quick Installation Guide (QIG) x 1

3. CD-ROM

(with User’s Manual and QIG)

x 1

4. Power Adapter (DC 5V) x 1

5. Antenna x 2

It is recommended to keep the original

packing material for possible future shipment

when repair or maintenance is required. Any

returned product should be packed in its

original packaging to prevent damage during

delivery.

Network Layout with EAP110s

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

System Overview

Connector Panel

EAP110 Connector Panel

1 5V 1A Attach the power adapter here.

2 LAN(PoE)

Attach the Ethernet cable here for connecting to wired local network. This port supports

PoE as well which can be connected to a PSE (power sourcing equipment) as an

alternative power sourcing.

3 WES

Press to start running WES process.

WES Role

Master (Press for more than 3

seconds until the WLAN LED

blinks twice and then release)

Slave (Press once until the WLAN

LED starts blinking and then

release right away)

WES Start WLAN LED BLINKING SLOWLY WLAN LED BLINKING QUICKLY

WES Success WLAN LED ON constantly for 5 seconds

WES Fail WLAN LED OFF for 5 seconds

3 Reset Press and hold the button for more than 10 seconds until WLAN LED OFF. WLAN ON

while reset is successful.

4 Antenna

Connector

Attach the antennas here. The system supports one RF interface with two SMA

connectors.

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

LED Panel

EAP110 LED Panel

LAN LED

LED ON indicates LAN cable is connected; OFF indicates no connection; BLINKING

indicates transmitting data.

WLAN LED

LED ON indicates wireless is ready.

WES LED

To indicate WES status.

WES Role

Master (Press for more than 3

seconds until the WLAN LED

blinks twice and then release)

Slave (Press once until the WLAN

LED starts blinking and then

release right away)

WES Start WLAN LED BLINKING SLOWLY WLAN LED BLINKING QUICKLY

WES Success WLAN LED ON constantly for 5 seconds

WES Fail WLAN LED OFF for 5 seconds

Power LED

LED ON indicates power on; OFF indicates power off.

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

Hardware Installation

Please follow the steps mentioned below to install the hardware of EAP110:

1. Place the EAP110 at a best location.

The best location for EAP110 is usually at the center of your wireless network.

2. Connect EAP110 to your network device.

Connect one end of the Ethernet cable to the LAN port of EAP110 and the other end of the cable to a

switch, a router or a hub. EAP110 is then connected to your existing wired LAN network.

3. There are two ways to supply power over to EAP110.

(a)

Connect the DC power adapter to the EAP110 power socket.

Please only use the power adapter supplied with the EAP110 package. Using a different power

adapter may damage this system.

(b)

EAP110 is a powered device (PD) that can be powered up by PoE. Connect an IEEE

802.3af-compliant PSE device, e.g. a PoE-switch, to the LAN port of EAP110 by the Ethernet cable.

Now, the Hardware Installation is completed.

To double verify the wired connection between EAP110 and your switch/router/hub, please

check the LED status indication of these network devices.

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

Getting Started

4ipnet EAP110 supports web-based configuration. Upon the completion of hardware installation, EAP110 can

be configured through a PC by using its web browser such as Mozilla Firefox 2.0 or Internet Explorer version

6.0 and above.

The default values of LAN IP address and subnet mask of EAP110 are:

IP Address: 192.168.1.1

Subnet Mask: 255.255.255.0

Steps:

1. To access the web management interface, connect the administrator PC to the LAN port of EAP110 via

an Ethernet cable. Then, set a static IP address on the same subnet mask as EAP110 in TCP/IP of your

PC, such as the following example:

IP Address: 192.168.1.100

Subnet Mask: 255.255.255.0

2. Launch the web browser on your PC by entering the IP address of EAP110 (https://192.168.1.1) at the

address field (“https” is used for a secured connection), and then press Enter.

Example of entering EAP110'sdefault IP Address via a web browser

3. The following Admin Login Page will appear. Enter “admin” for both the Username and Password fields,

and then click Login.

Administrator Login Page

Quick Installation Guide

Quick Installation GuideQuick Installation Guide

Quick Installation Guide

EAP110 Enterprise Access Point ENGLISH

4. After a successful login into EAP110, a System Overview page of web management interface will

appear, as depicted below.

The Web Management Interface - System Overview Page

5. To logout, simply click on the Logout button at the upper right hand corner of the interface to return to the

Administrator Login Page. Click OK to logout.

Logout

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de 4IPNET

4IPNET

4IPNET EAP705 Manual de usuario

4IPNET

4IPNET EAP100 Manual de usuario

4IPNET

4IPNET EAP200 Manual de usuario

4IPNET

4IPNET EAP701 Manual de usuario

4IPNET

4IPNET EAP737 Manual de usuario

4IPNET

4IPNET OWL610 Manual del operador

4IPNET

4IPNET OWL530 Manual de usuario

4IPNET

4IPNET EAP200 Manual de usuario

4IPNET

4IPNET EAP330 Manual de usuario

4IPNET

4IPNET EAP210 Manual de usuario

4IPNET

4IPNET EAP700 Manual de usuario

4IPNET

4IPNET EAP210 Manual de usuario

4IPNET

4IPNET EAP220 Manual de usuario

4IPNET

4IPNET EAP727 Manual de usuario

4IPNET

4IPNET OWL630 Manual de usuario

4IPNET

4IPNET OWL400 Manual de usuario

4IPNET

4IPNET EAP200 Manual de usuario

4IPNET

4IPNET EAP706 Manual de usuario

4IPNET

4IPNET OWL300 Manual de usuario

4IPNET

4IPNET EAP210 Manual de usuario

4IPNET

4IPNET OWL530 v1.00 Manual de usuario

4IPNET

4IPNET EAP300 Manual de usuario

4IPNET

4IPNET EAP757 V1.00 Manual de usuario

4IPNET

4IPNET EAP260 Manual de usuario

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario