Yamaha DM2000 V2.1 Instrucciones y recetas

DM2000 V2.1 Supplementary Manual

DM2000 system software V2.1 contains the following changes from V2.0.

❏

MIX C-R SOURCES parameter added to

Control Room Monitor (page 159)

A “MIX C-R SOURCES” parameter has been added in the

CONTROL ROOM SETUP page. In V2.0, you could

choose one item from 2TR D1, D2, D3, A1, or A2 as a

monitor source, plus other sources (STEREO, ASSIGN1,

or ASSIGN2). In V2.1, you can turn the MIX C-R

SOURCES parameter off to disable this simultaneous

selection.

❏

MIX MONITOR SOURCES parameter

added to Surround Monitor (page 160)

A “MIX MONITOR SOURCES” parameter has been

added to the SURROUND MONITOR page. In V2.0, you

could choose ASSIGN1 or ASSIGN2 in addition to a BUS

as the monitor source, but in V2.1 you can turn this

parameter off to disable this simultaneous selection.

❏

THX presets added to Surround Monitor (page 161-163)

Presets for the THX pm3 monitor system have been added to the bass management settings for surround monitor-

ing. Several supplements have also been added regarding the surround monitor settings, so please replace the cor-

responding pages with the following.

Conﬁguring Surround Monitoring

Surround monitoring, including speaker setup, monitor matrix, Bass Management, and monitor

alignment, is conﬁgured on the Surround Monitor Setup page.

1 Use the MONITOR [DISPLAY] button to locate the Surround Monitor Setup

page.

2Use the cursor buttons to select the parameters, and use the Parameter wheel,

INC/DEC buttons, and [ENTER] button to set them.

SPEAKER SETUP:

These parameters are for setting the volume balance of the surround monitor

speakers. Select the OSC (Oscillator) parameter and choose from PINK NOISE, 500-2K (pink noise

through a 500 Hz to 2 kHz BPF), 1K (1 kHz sinewave),or 50 Hz (50 Hz sinewave). Use the ON/OFF

button to turn the Oscillator on and off. When on, the Oscillator outputs a signal at –20 dB to the

Surround Channels whose icons are highlighted. You can turn on and off Oscillator output for

speakers individually. Speaker icons can be selected by using the cursor buttons. The signal phase of

the LFE Channel can be reversed by using the SW phase button.When ROTATE is on, the Oscillator

signal is output by each speaker in turn in a clockwise direction (3 second signal, 2 second pause).

SURR. MODE:

This indicates the currently selected Surround mode, which is set on the Surround

Mode page (

see page 97

MONITOR MATRIX:

This is used to select the Surround Monitor Matrix. In 6.1 Surround mode,

you can select 6.1, 5.1, 3-1, or ST. In 5.1 Surround mode, you can select 5.1, 3-1, or ST. In 3-1 Sur-

round mode, you can select 3-1 or ST.

When a down mix Monitor Matrix is selected, you can attenuate signals by using theATT parameters.

You can use the Surround Monitor settings in Stereo mode, but Monitor Matrix is ﬁxed to ST.

The following screen shows an example in 6.1 Surround mode and 3-1 Monitor Matrix mode.

•BASS MANAGEMENT

You can set the ﬁlter and attenuator settings for each Surround Monitor Channel using eight preset

Bass Management modes. The following presets are available:

ATT1: Adjusts the level difference between LR and LsRs.

ATT2: Adjusts the level difference between C and Bs.

AMP: Corrects the LFE channel level.

Note:

If you had been monitoring with the surround mode set to 6.1 and the monitor matrix mode

set to 6.1 on DM2000 units with system software earlier than V2.1, the playback may not always be

correct on V2.1.

Note:

If you choose monitor matrix mode = 3-1, you must set the following three attenuation amounts

to the same value.

• ATT1 for surround mode 3-1

• ATT4 for surround mode 5.1

• ATT5 for surround mode 6.1

These ATT values are not attenuators for down-mixing; rather, they are used as monitor adjustment

attenuators for lowering the playback volume of the Ls, Rs, Ls2, and Rs2 speakers.

Presets Parameters

No. Title HPF 1, 2, 3 LPF1 LPF2 ATT 1 & 2 AMP

DVD LFE80Hz 80–12 80–24 80–24 0 10

DVD LFE120Hz 80–12 120–42 80–24 0 10

Movie LFE80Hz 80–12 80–24 80–24 –3 10

Movie LFE120Hz 80–12 120–42 80–24 –3 10

Bypass THRU THRU MUTE 0 0

THXD

THX DVD 80-12L 120-42 80-24L 0 10

THXF

THX Movie 80-12L 120-42 80-24L –3 10

THXM

THX Music 80-12L 120-42 80-24L 0 10

HPF1–3: Cut the low range so that the speakers’ supporting frequency ranges will not interfere with the sub-

woofer signals.

HPF1–2: Cut the high range so that the subwoofer’s supporting frequency ranges will not interfere with other

speakers’ signals.

You can set the Bass Management parameters in the following ranges:

The HPF 1, 2, 3, and LPF 1 & 2 values indicate a cut-off frequency and a filter response. For example, “80-12”

means a cutoff frequency of 80 Hz and a filter response of –12 dB/octave.

“L” means Linkwitz filter. Other filters are Butterworth.

About the Presets

(1)

DVD LFE80Hz

This is a preset optimized for DVD-Video production. The LFE playback bandwidth is set up to 80

Hz. When using this preset, we recommend that you use an external device to apply an LPF (fc=80

Hz, –24 dB/oct) to the LFE master source.

To monitor audio on DVD-Audio or SACD discs, change the LFE level (AMP) and LPF (LPF1) to

0 dB and THRU, respectively, if necessary.

The LFE output gain on some DVD players and decoders may already be set to +10 dB. To monitor

the output from such devices, change the LFE level (AMP) to 0 dB.

(2)

DVD LFE120Hz

This is also a preset optimized for DVD-Video production. This preset is the same as preset (1) men-

tioned above, except that the LFE playback bandwidth is set up to 120 Hz. Use this preset to monitor stan-

dard LFE signals recorded on DVD-Video discs that include the high-end frequency ranges (120 Hz).

(3)

Movie LFE80Hz

This preset is the same as preset (1) mentioned above, except that the output level of surround chan-

nels is set to –3 dB when the Monitor Matrix mode is 5.1 or 6.1. This preset is suitable for movie

production.

When using this preset, we recommend that you use an external device to apply an LPF (fc=80 Hz,

–24 dB/oct) to the LFE master source.

(4)

Movie LFE120Hz

This preset is the same as preset (2) mentioned above, except that the output level of surround chan-

nels is set to –3 dB when the Monitor Matrix mode is 5.1 or 6.1. This preset is suitable for movie

production.

(5)

Bypass

Use this preset not only for bass management but to bypass all parameters, such as the LFE level &

LPF, surround channel level, etc.

To disable only the bass management, select another preset, then turn off the BASS MANAGE-

MENT ON/OFF button.

■

THX Presets:

The following presets have been approved by THX™ Ltd. for use in THX pm3™ Certiﬁed Studios*.

They are designed to provide dedicated parameters for the proper playback of multi-channel audio

content in bass managed systems and to be compatible with subwoofer-satellite type consumer systems.

*Use of a THX preset does not permit a studio to use the designation - THX pm3 Certiﬁed Studio.

The THX pm3 Studio Certiﬁcation Program uses performance and design speciﬁcations to create cal-

ibrated environments for optimum sound and picture presentation. For more information, visit the

THX website at http://www.thx.com

Note:

•If you select preset THXD or THXF, you cannot change the parameters.

•If you select preset THXM, you can switch AMP between 10 dB and 0 dB. However, you cannot

change other parameters.

Parameters Range

HPF 1, 2, 3

THRU, 80-12, 80-12L, 80-24, 80-24L

LPF1

THRU, 80-24, 80-24L, 120-42

LPF2

THRU, 80-24, 80-24L, MUTE

ATT 1 & 2

0 to –12 dB (1 dB steps)

AMP

0 to +12 dB (1 dB steps)

U.R.G., Pro Audio & Digital Musical Instrument Division, Yamaha Corporation

[THXD]

THX DVD

This preset is conﬁgured for DVD-Video production. Use this preset when mixing and/or monitor-

ing audio content not from a theatrical ﬁlm source. The parameters cannot be changed.

[THXF]

THX Film

This preset is conﬁgured for Film pre-production. Use this preset when mixing and/or monitoring

theatrical ﬁlm-based content (such as a pre-mix for ﬁlm). The parameters cannot be changed.

[THXM]

THX Music

This preset is conﬁgured for DVD-Music production. Use this preset when mixing and/or monitor-

ing multi-channel music content (including DVD-Audio and SACD). Only one parameter can be

changed. The LFE gain (AMP) can be set to +10dB (default) or 0dB. Select the level that complies

with the standards of the target media. Please note: The LFE output gain on some DVD players,

receivers, and/or decoders may already be set to +10dB. Select the 0dB setting only if the destination

environment (home theatre, etc.) has the LFE gain set to 0dB. Otherwise, use the default setting.

•MONITOR ALIGNMENT ATT & DLY ON/OFF

These buttons are used to turn on and off the Monitor Align-

ment Attenuator and Delay parameters of all Surround speak-

ers. The MONITOR ALIGNMENT diagram and Surround

Channel Attenuator and Delay parameters, which are dis-

played when either of these buttons are selected, allow you to

align the surround monitor speakers by attenuating and

delaying Surround Channels as necessary. The Attenuator

parameters can be set –

∞

, –12 dB to +12 dB in 0.1 dB steps. The Delay parameters can be set from

0 to 30 msec in 0.02 msec steps.

❏

Canceling the parameter display value in

the channel strip display (page 274)

A “Ch Numeric Disp OFF” preference has been added to

the PREFERENCES 1 page. In V2.0, the channel strip dis-

play would switch to showing the parameter value when

you operated a channel fader or encoder (pan setting). If

you turn on this preference item, the display will not be

switched to the parameter value.

❏

MY16-C card support (pages 70 and 349)

The MY16-C CobraNet interface card is now supported. However, the following restrictions apply when installing

the card into a DM2000 slot.

•Only one MY16-C card can be used simultaneously, and it can be installed only in one of SLOT 1–3.

•Audio signal transmission and reception are supported, but control signals are not supported.

Please refer to the following website for the latest information on compatible cards, and on the number of cards

that can be installed in combination with other cards.

http://www.yamahaproaudio.com

Note:

•Please note that the above settings apply only to the signals being monitored. They do not affect the

normal bus outputs.

•If you’re monitoring in surround mode 6.1 and monitor matrix mode 6.1, you’ll need to make the

above settings separately from when in other modes.

Tip:

The settings you make here can be stored in the surround monitor library.

Tabla de contenidos

Otros manuales de Software de Yamaha

Yamaha

Yamaha ASIO DirectKS Manual de usuario

Yamaha

Yamaha MOTIF XS6 Manual de usuario

Yamaha

Yamaha MagicStomp Manual de usuario

Yamaha

Yamaha QS1-WD Manual de usuario

Yamaha

Yamaha LS9 Editor Manual de usuario

Yamaha

Yamaha mLAN mLAN Driver Manual de usuario

Yamaha

Yamaha DME32 V1.1 Guía de configuración

Yamaha

Yamaha Studio Manager Manual de usuario

Yamaha

Yamaha Arp Manual de usuario

Yamaha

Yamaha PM1D Manager V2 Instrucciones y recetas

Yamaha

Yamaha Synth Manual de usuario

Yamaha

Yamaha Song Filer Manual de usuario

Yamaha

Yamaha MOTIF RACK Music System Manual de usuario

Yamaha

Yamaha 02R96 Version 2 Manual de usuario

Yamaha

Yamaha MOTIF-RACK ES Manual de usuario

Yamaha

Yamaha IMX644 Manager Manual de usuario

Yamaha

Yamaha YC-3B Manual de usuario

Yamaha

Yamaha LS9-16 Manual de usuario

Yamaha

Yamaha MOTIF6 Voice Editor Manual de usuario

Yamaha

Yamaha RS7000 Ver.1.2 Instrucciones de instalación y funcionamiento

Yamaha

Yamaha FIRESTATION MLAN PATCHBAY Manual de usuario

Yamaha

Yamaha A4000 Manual de usuario

Yamaha

Yamaha DM 1000 Manual de usuario

Yamaha

Yamaha Add-On Effects Manual de usuario

Manuales populares de Software de otras marcas

COMPRO

COMPRO COMPROFM Manual de usuario

Muratec

Muratec OFFICEBRIDGE ONLINE Manual de usuario

Oracle

Oracle Contact Center Anywhere 8.1 Manual de usuario

Adobe

Adobe 65007312 - Photoshop Lightroom Manual

Avaya

Avaya NULL One-X for RIM Blackberry Manual de usuario

HP ProLiant BL420c Manual de usuario

PS Audio

PS Audio PowerPlay Manual del propietario

Brady

Brady LOCKOUT PRO 3.0 Manual de servicio

Avaya

Avaya Interaction Center Manual de usuario

Texas Instruments

Texas Instruments TI-83 Plus Silver Edition Manual

Novell

Novell GROUPWISE 8 - INTERNET AGENT Manual de usuario

Oracle

Oracle Application 9i Manual de usuario

Acer

Acer RDM Manual de usuario

Canon

Canon Vixia HF21 Manual de usuario

Canon

Canon ZR950 Manual de usuario

Samsung

Samsung Auto Backup Manual de usuario

Polycom

Polycom Vortex EF2201 Instrucciones de instalación y funcionamiento

Brocade Communications Systems

Brocade Communications Systems Brocade 8/12c Manual de usuario