Xylem WTW TetraCon 925 Manual de usuario

OPERATING MANUAL

ba75824e04 04/2015

TetraCon®925 (/C)(-P)

CONDUCTIVITY CELL

TetraCon®925

TetraCon®925-P

TetraCon®925/C

OPERATING MANUAL

ba75824e04 04/2015

TetraCon®925

Reproduction in whole - or even in part - is prohibited without the

express written permission of WTW GmbH, Weilheim.

Printed in Germany.

For the most recent version of the manual, please visit

www.WTW.com.

TetraCon®925 (/C)(-P) Contents

ba75824e04 04/2015

Contents

1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.1 Structure and function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

1.2 Recommended fields of application . . . . . . . . . . . . . . . . . . . . . . 5

2 Measuring / Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.2 Opening and closing the IDS plug connection

(TetraCon®925-P) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

3 Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

4 What to do if... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

5 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5.1 General data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

5.2 Measuring ranges, resolution, accuracy . . . . . . . . . . . . . . . . . . 11

5.3 Accuracy of the IDS measuring technique . . . . . . . . . . . . . . . . 11

6 Wear parts and accessories . . . . . . . . . . . . . . . . . . . . . . . . . 12

Contents TetraCon®925 (/C)(-P)

4ba75824e04 04/2015

TetraCon®925 (/C)(-P) Overview

ba75824e04 04/2015

1 Overview

1.1 Structure and function

Structure

Automatic sensor

recognition

The sensor electronics with the stored sensor data is in the connecting head.

The data include, among other things, the sensor type and series number.

With each calibration, the calibration data is written in the sensor and the

calibration history is recorded. The data is recalled by the meter when the

sensor is connected and is used for measurement and for measured value

documentation. Storing the calibration data in the sensor ensures that the

correct cell constant is automatically used if the sensor is operated with

several meters.

The digital transmission technique guarantees the failure-free

communication with the meter even with long connection cables. If the sensor

firmware is enhanced by WTW, it can be updated via the meter.

1.2 Recommended fields of application

On site measurements in rivers, lakes and wastewater

Fish farming

Ground water measurements

Applications in water laboratories

1Voltage electrode (inside, 2x)

2Current electrode (ring, 2x)

3Temperature sensor in graphite enclosure

4Shaft

5Connecting head with active electronics

6Connection cable (TetraCon®925(/C))

7IDS plug (TetraCon®925-P)

41, 2 3 5

TetraCon 925(/C)

TetraCon 925-P

Measuring / Operation TetraCon®925 (/C)(-P)

6ba75824e04 04/2015

Due to the use of high performance PEEK material for the connection

technology TetraCon®925/C has an improved chemical resistance,

especially in acid media (eg. As electroplating baths).

NOTE

Concentrated or strong oxidizing acids and organic solvents can

damage or destroy the sensor.

2 Measuring / Operation

2.1 Commissioning

Scope of delivery Conductivity measuring cellTetraCon®925 (/C)(-P)

Operating manual

Preparing the

sensor for

measurement

TetraCon®925(/C) Connect the sensor to the meter.

The sensor is immediately ready to measure.

TetraCon®925-P Connect the sensor to a free IDS sensor plug-in

position of the multi parameter probe or to an IDS

connection of the meter. To open and close the

IDS plug-in position please note the section 2.2

OPENING AND CLOSING THE IDS PLUG CONNECTION

(TETRACON®925-P).

The sensor is immediately ready to measure.

Connection cables in different lengths to connect

the TetraCon®925-P sensor to the meter are listed

in chapter 6 WEAR PARTS AND ACCESSORIES.

TetraCon®925 (/C)(-P) Measuring / Operation

ba75824e04 04/2015

2.2 Opening and closing the IDS plug connection

(TetraCon®925-P)

This section only applies to the IDS plug variant, TetraCon®925-P.

Opening the plug

connection

If necessary, clean the plug connection

Open the locking device (step 1)

Use your thumb and index finger to press the clips of the connector

together, and pull the connector out of the plug (step 2).

Closing the plug

connection

Make sure that the plug connection is completely dry and clean.

Align the guidance of the connector with the groove in the plug and insert

the connector in the unlocked plug until it catches (step 3).

Close the locking device (step 4).

Plug connection

closed and locked

Guidance

Groove

Cleaning TetraCon®925 (/C)(-P)

8ba75824e04 04/2015

3 Cleaning

NOTE

Prior to cleaning, disconnect the sensor from the meter.

Outside cleaning We recommend to clean the sensor thoroughly, especially before measuring

low conductivity values.

After cleaning, thoroughly rinse with deionized water and recalibrate if

necessary.

Aging of the

conductivity

measuring cell

Normally, the conductivity measuring cell does not age. Special measuring

media (e.g. strong acids and bases, organic solvents) or temperatures that

are too high may considerably reduce its lifetime or lead to damage. The

warranty does not cover failure caused by measuring conditions and

mechanical damage.

Disposal We recommend to dispose of the measuring cell as electronic waste.

4 What to do if...

Contamination Cleaning procedure

Lime sediments Immerse in acetic acid for 5 minutes (volume

share = 10 %)

Fat/oil Clean with warm water that contains wash-

ing-up liquid

Error symptom Cause Remedy

No temperature or conductivity

display

– No connection between meter

and conductivity measuring

cell

– Cable defective

– Establish connection

between meter and

conductivity measuring

cell

Measurement delivers implausi-

ble conductivity values

– Measuring range exceeded

– Contamination in the area of

the electrodes

– Electrodes damaged

– Make sure the correct

sensor is being used for

the application

– Clean the conductivity

measuring cell (see

section 3).

– Return the sensor

Incorrect temperature display – The temperature sensor is not

immersed deep enough in the

measuring solution

– Temperature sensor

defective

– Observe the minimum

immersion depth

– Return the conductivity

measuring cell

TetraCon®925 (/C)(-P) Technical data

ba75824e04 04/2015

5 Technical data

5.1 General data

General features Measuring principle Four-electrodes measurement

Cell constant 0.475 cm-1 ±1.5 %

Temperature sensor Integrated NTC 30 (30 kat 25 °C / 77 °F)

Dimensions

(in mm)

Weights TetraCon®925(/C) 60 g (without cable)

TetraCon®925-P 65 g

Materials Shaft Epoxy

Connection head TetraCon®925(-P):POM

TetraCon®925/C:PEEK

Conductivity electrodes Graphite

Thermistor enclosure Graphite

Connection cable Lengths TetraCon®925:1,5 / 3 m

TetraCon®925-P:

1,5 / 3 / 6 / 10 / 15 / 25 / 40 / 60 / 100 m

TetraCon®925/C:1,5 m

Diameter 4.3 mm

120,0

176,0

222,8

15,3

21,7

TetraCon 925(/C):

TetraCon 925-P:

Technical data TetraCon®925 (/C)(-P)

10 ba75824e04 04/2015

Smallest allowed

bend radius

Fixed installation:20 mm

Flexible use:60 mm

Plug type Socket, 4 pins

IDS plug

(TetraCon®925-P)

Connection type 4-pole, watertight plug connection with lock,

reverse polarity protected

Materials Synthetic materials: Glass fiber reinforced

Noryl, TPU, TPC-ET, POM, PEEK, PBT

O-ring: FPM

Contacts gold-plated

Pressure

resistance

Sensor with connection

cable

IP 68 (2.5 x 105Pa or 2.5 bar)

Cable plug

(TetraCon®925)

IP 67 (when plugged in)

The TetraCon®925 (/C)(-P) meets the requirements according to article

3(3) of the directive, 97/23/EC ("pressure equipment directive").

Measurement

conditions

Conductivity measuring

range

1 S/cm ... 2 S/cm

Temperature range -5 ... 70 °C (100 °C) (23 ... 158 °F (212 °F))

Max. admissible overpres-

sure

TetraCon®925(/C):2,5 x 105Pa (2,5 bar)

TetraCon®925-P:1 x 106Pa (10 bar)

Minimum depth of immer-

sion

36 mm

Maximum depth of immer-

sion

(at temperature)

Whole sensor + cable up to 70 °C (158 °F)

Sensor shaft only (=120 mm) up to 100 °C

(212 °F)

Operating position Any

Storage conditions Recommended storing

method

In air

Storage temperature 0 ... 50 °C

Characteristic data

on delivery

Temperature responding

behavior

t99 (99 % of the final value display after)

<20s

Accuracy of the temperature

sensor

± 0,2 K

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Xylem

Xylem

Xylem WTW SenTix 950 Manual de usuario

Xylem

Xylem YSI Pro1020 Manual de usuario

Xylem

Xylem SENSUS PolluFlow Manual de usuario

Xylem

Xylem Domo M M-Bus Manual de usuario

Xylem

Xylem WTW pH 3110 Manual de usuario

Xylem

Xylem WTW Cond 3310 Manual de usuario

Xylem

Xylem WTW SenTix ORP-T 900-P Manual de usuario

Xylem

Xylem WTW Cond 3310 IDS Manual de usuario

Xylem

Xylem PolluStat Manual de usuario

Xylem

Xylem WTW Multi 3320 Manual de usuario

Xylem

Xylem SENSUS Act-Pak 1100D Manual de usuario

Xylem

Xylem Sensus PulseRF HRI-A3 Manual de usuario

Xylem

Xylem YSI Pro10 Manual de usuario

Xylem

Xylem WTW Cond 3210 Manual de usuario

Xylem

Xylem Sensus MD 1770 Manual de usuario

Xylem

Xylem SI Analytics HandyLab 100 Manual de usuario

Xylem

Xylem WTW Oxi 3210 Manual de usuario

Xylem

Xylem Sensus Domo R Manual de lista de piezas

Xylem

Xylem Sensus Residia-M Manual de usuario

Xylem

Xylem WTW Turb 750 T Manual de usuario

Xylem

Xylem YSI MultiLab 4010P-1 Manual de usuario

Xylem

Xylem YSI Pro20 Manual de usuario

Xylem

Xylem WTW Turb 430 IR/T Manual de usuario

Xylem

Xylem wtw Cleaning Air Box -115 VAC Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario