Xylem YSI Pro10 Manual de usuario

Pro10

Quick Start Guide

Item #605193

This Quick Start Guide is meant to serve as a quick reference in calibrating and

operating the Pro10. It is not intended to replace the information found in the User

Manual.

Getting Started

Unpack the instrument and install (2) C size batteries in the back of the instrument.

Tighten the four screws of the battery cover on to the back of the instrument.

Installing the Sensor

Prior to use, install either a pH or ORP sensor into the 60510 cable assembly. Remove

the temporary plastic plug from the cable’s port by pulling it straight out of the port.

Remove the plastic plug from the sensor’s connector by pulling it straight off the sensor.

Insert the sensor into the port so the o-rings on the sensor are no longer visible. Hand

tightening the sensor into place by twisting it clockwise. Do not use a tool and do not

over tighten

Enable the correct ISE (either pH or ORP) in the instrument’s System Setup menu. Attach

the cable assembly to your instrument.

pH Calibration

The Pro10 pH sensor can be calibrated by performing a 1, 2 or 3-point calibration. At

least one of the calibration points must be done with pH buffer 7 or 6.86. For highest

accuracy, perform at least a 2-point calibration.

2 or 3-Point Calibration

1. Place the sensor in pH buffer 7 or 6.86 and allow the temperature and pH

readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight pH and press Enter. If pH is not listed as an option, check the System

Setup menu to ensure pH is enabled in the ISE Sensor Type menu.

4. Highlight 2 point or 3 point and press enter.

5. If necessary, use the up and down arrow keys to adjust the pH buffer value.

6. Press Enter to continue to second point.

ORP Calibration

1. Place the clean sensor in ORP calibration solution. Wait for the ORP and

temperature readings to stabilize.

2. Press and hold Cal for three seconds.

3. Highlight ORP and press Enter. If ORP is not listed as an option, check the

System Setup menu to ensure ORP is enabled in the ISE Sensor Type menu.

4. Use the up and down arrow keys to adjust the ORP calibration solution value.

5. Wait for the temperature reading to stabilize, then press Enter to complete the

calibration or press Cal to cancel.

6. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

7. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen. Refer to the troubleshooting section of the manual for a possible

solution or contact YSI Technical Support.

7. Rinse the sensor and place it in the second pH buffer (4/4.01 or 10/9.18). If

necessary, use the up and down arrow keys to adjust the pH buffer value.

8. Wait approximately 30 to 60 seconds for the pH sensor to stabilize and for the

temperature reading to stabilize.

9. Press Enter to either complete the 2-point calibration or to continue with the 3rd

calibration point. Or, press Cal to cancel.

10. If continuing on with a 3rd calibration point, rinse the sensor and place it in the

third pH buffer (4/4.01 or 10/9.18). If necessary, use the up and down arrow keys

to adjust the pH buffer value.

11. Wait approximately 30 to 60 seconds for the pH sensor to stabilize and for the

temperature reading to stabilize.

12. Press Enter to complete the 3-point calibration. Or, press Cal to cancel.

13. ‘Calibration Successful’ will display for a few seconds to indicate a successful

calibration and then the instrument will return to the Run screen.

14. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the calibration error message and return to the Run

screen.

Visit YSI.com/Pro10 to ﬁnd the

User Manual, specs, and accessories.

Item# 605193 Dwg# 605193

December 2019 Rev B

1725 Brannum Lane

Yellow Springs, OH 45387

(800) 765-4974, (937) 767-7241

[email protected]

Taking Measurements

1. Before taking measurements, be sure the instrument has been calibrated to

ensure the most accurate readings.

2. Install the sensor guard and then insert the probe into the sample.

3. Highlight Save and press Enter to store the reading. The instrument will conﬁrm

the reading was successfully saved.

Contact Information

This page is intentionally left blank.

Tabla de contenidos

Otros manuales de Instrumento de medición de Xylem

Xylem

Xylem WTW Multi 3320 Manual de usuario

Xylem

Xylem SENSUS Act-Pak 1100D Manual de usuario

Xylem

Xylem mjk MagFlux Manual de usuario

Xylem

Xylem WTW OxiTop-i Manual de usuario

Xylem

Xylem wtw inoLab Multi 9620 IDS Manual de usuario

Xylem

Xylem SENSUS PolluTherm Manual de usuario

Xylem

Xylem Sontek River Surveyor RS5 Manual de usuario

Xylem

Xylem Sensus Residia-M Manual de usuario

Xylem

Xylem WTW pH 3310 Manual de usuario

Xylem

Xylem SI Analytics Lab 865 Manual de usuario

Xylem

Xylem WTW Cond 3310 Manual de usuario

Xylem

Xylem YSI Pro1020 Manual de usuario

Xylem

Xylem WTW Oxi 3205 Manual de usuario

Xylem

Xylem YSI MultiLab 4010P-1 Manual de usuario

Xylem

Xylem SonTek-SL Manual de usuario

Xylem

Xylem WTW Cond 7310 Manual de usuario

Xylem

Xylem WTW Turb 750 IR Manual de usuario

Xylem

Xylem wtw pH/ION 7320P Manual de usuario

Xylem

Xylem sensus AutoRead Manual de usuario

Xylem

Xylem OMNI sensus C2 Manual de usuario

Xylem

Xylem WTW SenTix ORP-T 900 Manual de usuario

Xylem

Xylem FLYGT Concertor APP 411 Manual de usuario

Xylem

Xylem WTW inoLab Multi 9630 IDS Manual de usuario

Xylem

Xylem YSI DIQ/S 182-XT-4-PR Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario