Xylem YSI Pro20 Manual de usuario

Pro20 / Pro20i

Quick Start Guide

Item #605645

This Pocket Guide is meant to serve as a quick reference in calibrating and operating the

Pro20/Pro20i. It is not intended to replace the information found in the User Manual.

Installing the DO Membrane

1. Prepare the O2probe solution according to the instructions on the bottle. After

mixing, allow the solution to sit for 1 hour. This will help prevent air bubbles

from later developing under the membrane.

2. Remove, and discard the red protective cap or used membrane from the sensor.

3. Thoroughly rinse the sensor tip with distilled or deionized water.

4. Fill a new membrane cap with probe solution. Avoid touching the membrane

portion of the cap.

5. Thread the membrane cap onto the sensor, moderately tight. A small amount of

electrolyte will overﬂow.

6. Screw the probe sensor guard on moderately tight.

Setting Sensor & Membrane Type

The instrument will step you through an initial conﬁguration when powered on for the

ﬁrst time. This allows you to set the language, sensor, and membrane options. Use the

up or down arrow keys to highlight the appropriate language, sensor, and membrane,

then press enter to conﬁrm. To change the sensor or membrane type after the initial

conﬁguration, press the Menu key.

The instrument’s Sensor Type must be conﬁgured for the sensor installed.

Failure to do this may result in damage not covered under warranty.

Barometer Calibration

The barometer reading must be accurate to ensure accurate DO% calibrations and DO

readings.

If your barometer requires an adjustment:

1. Determine your local barometric pressure (BP) in mmHg from a mercury

barometer, an independent laboratory, or from a local weather service. If the

BP reading has been corrected to sea level, use the following equation to

determine the true BP in mmHg for your altitude.

True BP = (Corrected BP in mmHg) – {2.5 * (Local Altitude in feet/100)}

DO Calibration

The Pro20/Pro20i can be calibrated in % saturation, mg/L, or ppm. Calibration of any

option (%, mg/L, or ppm) will automatically calibrate the others. The Pro20/Pro20i can

be calibrated with the press of one key when One Touch Cal is enabled in the System

Setup menu.

The following procedure outlines the % saturation calibration option with and without

One Touch Cal enabled.

1. Moisten the sponge in the cal/transport sleeve with a small amount of water

and install it on the probe. The cal/transport sleeve ensures venting to the

atmosphere. Make sure the DO and temperature sensors are not immersed

in the water.

2. Turn the instrument on. If using a polarographic sensor, wait 10 minutes for the

DO sensor to stabilize. Galvanic sensors do not require a warm up time.

3. Ensure the barometer reading and salinity correction values along the bottom of

the screen are accurate.

4. Press and hold the Cal key for three seconds.

5. If One Touch Cal is enabled, the instrument will indicate Calibrating %DO on

the display and automatically calibrate the sensor to the barometer reading and

salinity correction value.

6. If One Touch Cal is not enabled, highlight %or %Local and press Enter. The

Pro20/Pro20i will display the current DO% and temperature readings along

with the % calibration value. Wait at least 3 seconds, then, once the DO% and

temperature readings are stable, press Enter to complete the calibration.

7. Calibration Successful will display for a few seconds to indicate a successful

calibration and then the instrument will return to the run screen.

8. If the calibration is unsuccessful, an error message will display on the screen.

Press the Cal key to exit the error message and return to the run screen.

Salinity Compensation Calibration

The Pro20/Pro20i uses an inputted salinity value in ppt (parts per thousand) to

compensate dissolved oxygen mg/L values.

2. From the run screen, use the up or down arrow keys to highlight the barometer

box then press enter.

3. Use the up or down arrow keys to adjust the barometer reading to the local,

true barometric pressure.

4. Press enter to conﬁrm and save the barometer adjustment.

To adjust the salinity compensation value:.

1. Use the up or down arrow keys to highlight the salinity box on the run screen,

then press enter.

2. Use the up or down arrow keys to adjust the salinity compensation value to the

salinity of the water you are testing.

3. Press enter to conﬁrm and to save the new salinity compensation value.

Taking Measurements

The Pro20/Pro20i can be calibrated in %saturation, mg/L, or ppm. Calibration of any

option (%, mg/L, or ppm) will automatically calibrate the others. The Pro20/Pro20i can

be calibrated with the press of one key when One Touch Cal is enabled in the System

Setup menu.

The following procedure outlines the % saturation calibration option with and without

One Touch Cal enabled.

1. Turn the instrument on and wait 5-15 minutes if using a polarographic sensor.

2. To take readings, insert the probe into the sample. Move the probe in the

sample at a rate of at least 6 inches per second until the readings stabilize.

3. Highlight Save and press Enter to store the reading. The instrument will

conﬁrm that the reading was successfully saved.

Visit YSI.com/Pro20 or YSI.com/Pro20i to

ﬁnd the User Manual, specs, and accessories.

Item# 605645 Dwg# 605645

January 2020 Rev E

1725 Brannum Lane

Yellow Springs, OH 45387

(800) 765-4974, (937) 767-7241

[email protected]

Contact Information

This page is intentionally left blank.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de Xylem

Xylem

Xylem optimyze Manual de usuario

Xylem

Xylem WTW Cond 3310 IDS Manual de usuario

Xylem

Xylem ebro FOM 330 Manual de usuario

Xylem

Xylem PolluStat Manual de usuario

Xylem

Xylem Sensus Residia-M Manual de usuario

Xylem

Xylem SonTek RiverSurveyor Manual de usuario

Xylem

Xylem YSI Pro1030 Manual de usuario

Xylem

Xylem mjk MagFlux Manual de usuario

Xylem

Xylem SI Analytics Lab 865 Manual de usuario

Xylem

Xylem WTW SenTix ORP-T 900 Manual de usuario

Xylem

Xylem SI Analytics HandyLab 200 Manual de usuario

Xylem

Xylem SI Analytics Lab 855 Manual de usuario

Xylem

Xylem WTW Alyza IQ PO4 Manual de usuario

Xylem

Xylem WTW pHotoFlex Turb Manual de usuario

Xylem

Xylem YSI DIQ/S 182-XT-4-PR Manual de usuario

Xylem

Xylem Sensus Modbus RTU Manual de usuario

Xylem

Xylem SENSUS PolluTherm Manual de usuario

Xylem

Xylem SENSUS Act-Pak 1100D Manual de usuario

Xylem

Xylem YSI pH1200 Manual de usuario

Xylem

Xylem wtw inoLab Multi 9620 IDS Manual de usuario

Xylem

Xylem wtw Multi 3410 Manual de usuario

Xylem

Xylem EXO Series Manual de usuario

Xylem

Xylem wtw Cond 3110 Manual de instrucciones

Xylem

Xylem WTW Turb 430 IR/T Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario