Xerox 5400DX - Phaser B/W Laser Printer Manual de usuario
XEROX®PHASER 5400
TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
XEROX PHASER 5400 TONER CARTRIDGE
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
First introduced in October 2001, the Phaser 5400 machine is based on a 40ppm, 1200dpi Fuji-Xerox laser printer engine.
This engine is capable of printing on 11” x 17” paper. The exact engine number is not known, but if Fuji-Xerox has kept with past
practices, it would be the XP-40 (40ppm). The cartridge itself (Xerox # 113R00495) is very easy to remanufacture, and with list
prices above $296.00 USD* per cartridge, a nice profit maker as well.
The cartridge is rated for 20,000 pages and is loaded with 820g of toner. A complete line of supplies is available for these
cartridges. These machines tend to be used as workgroup printers, so if you have a customer that has one, the cartridge volume
will be on the high side. While this cartridge looks very similar to the Lexmark W812 from the outside, it is very different. This is
especially true for the toner. It should also be noted that there is a chip, and it must be changed each cycle. The chip itself is an
RF type and is a black round disk that fits into the fill plug.
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
REMANUFACTURING THE XEROX
PHASER 5400 TONER CARTRIDGE
By Mike Josiah and the Technical Staff at UniNet
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
The only real similarity to the Lexmark W812 is that they both use white plastic pins located on each side of the cartridge that
lock the two halves of the cartridge in place. The heads of these pins have what looks like a one way screw head on them
(see above photo). We have contacted multiple specialty screw manufacturers to see if a special tool is available, but were not
able to find one. They can be removed by inserting a 1” long #6 or #8 wood screw into the center of the pin. You can then twist
the pin and pull it out.
*Cartridge pricing as of June 2007
MACHINES BASED ON THE XEROX 5400 ENGINE:
Phaser 5400
Phaser 5400 N
Phaser 5400 DT
Phaser 5400 DX
How to run test prints as well as printer error codes will be discussed at the end of this article.
SUPPLIES REQUIRED:
1. New toner (820g) for use in Phaser 5400
2. New drum for use in Phaser 5400
3. Replacement cartridge pins
4. New replacement chip
5. New doctor blade (optional)
6. New magnetic roller sleeve (optional)
7. Sealing strip
8. Cotton swabs
9. Isopropyl alcohol
10. Drum padding powder
11. Conductive grease
12. Dedicated magnetic roller cleaner
TOOLS REQUIRED:
1. Phillips head screwdriver
2. Small common screwdriver
3. Needle nose pliers
4. Spring hook
5. Vacuum approved for toner
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
1. Turn the cartridge so that the handle is towards you (spring on the right). On either side of the cartridge is a white plastic pin
with one way screw heads. These pins are what hold and lock both halves together. Specialty drivers to remove them are not
available (at the time of this writing) so the only way to remove them (at the time of this writing), is to insert a 1” long or
#8 woodscrew into the center of the pin. Pull/pry out to remove. Leave the screws in so they can easily be installed.
4. Remove the two screws and white plastic drum axle pin from
the single gear side of the drum.
5. Remove the drum.
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
2. Remove the spring from the right side of the cartridge.
Separate the two halves.
3. Remove the two screws and metal drum axle pin from the
double gear side of the drum.
6. Remove the PCR from its holders. 7. Remove the two screws and wiper blade.
8. Clean out the waste chamber. Be very careful not to lose or
damage the foam wiper blade seal. This seal is very fragile and
a vacuum/compressed air cleaning system will damage it if
you are not careful.
9. Coat the wiper blade with your preferred lubricant, and
install in the cartridge. Install the two (gold)long screws, the
four short screws are for the drum axle pins only.
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
10. Clean the PCR contacts with a cotton swab and alcohol. 11. Clean the PCR with your preferred PCR cleaner and install
in the holders.
12. Install the drum, axle pins, and screws. Make sure that the metal axle pin is on the double gear side, and the white plastic
pin is on the single gear side. Although the toner hopper can be cleaned and filled through the fill plug, it is recommended that
the magnetic roller be removed and cleaned. This will also be necessary to do once a seal is available. The fill plug has a black
cover in the center that is held on by double sided tape. This cover is actually the chip, which must be replaced for the cartridge
to work.
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
13. With a small jeweler’s screwdriver, pry the black cover off
the fill plug.
14. With the pair of needle nose pliers, pull the fill plug out.
Grasp the plug by the small cross braces, and pull. This
method does not damage the plug seal. Dump out any remain-
ing toner from the hopper.
15. On the side opposite the fill plug, remove the two screws
and end cap.
16. Press in and lift up the locking tab on the right side of the
magnetic roller. With the keyed shaft of the magnetic roller
free, lift up on the keyed end by the locking tab. Pull the entire
magnetic roller assembly free.
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
17. Remove the two screws and doctor blade.
Clean out any remaining toner.
18. Install the seal.
Make sure the seal tab is slid into the seal tab slot.
19. Install the cleaned doctor blade and two screws.
Be careful not to damage the alignment pins.
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
20. Clean the magnetic roller assembly with a dedicated magnetic roller cleaner.
Install the assembly left side (round shaft) first.
Make sure the locking tab is firmly locked in place.
21. Install the end cap.
The gear posts must also align to the end cap holes.
Install the two screws.
22. Fill with 820g toner for Phaser 5400.
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
23. Install the fill plug, check for leaks. If the round chip fell off,
just throw it away. A new chip will be installed later in the
instruction.
24. Install the toner supply section onto the waste chamber.
Make sure the spring on the supply hopper fits into the plastic
ring on the waste hopper.
25. Install the two white plastic locking pins. 26. Remove the two screws from the white pins.
XEROX PHASER 5400 TONER CARTRIDGE REMANUFACTURING INSTRUCTIONS
© 2010 UniNet Imaging Inc. All trademark names and artwork are property of their respective owners. Product brand names mentioned are intended to show compatibility only.
UniNet Imaging does not warrant downloaded information. Unauthorized sale, reproduction or distribution of this article is prohibited. For additional support, please contact [email protected]
www.uninetimaging.com
Otros manuales para 5400DX - Phaser B/W Laser Printer
3
Este manual sirve para los siguientes modelos
1
Otros manuales de Accesorios de impresora de Xerox
Xerox
Xerox C11 - DocuPrint Color Inkjet Printer Manual de usuario
Xerox
Xerox 5500DN - Phaser B/W Laser Printer Manual de usuario
Xerox
Xerox 5500DN - Phaser B/W Laser Printer Manual de usuario
Xerox
Xerox 5500DN - Phaser B/W Laser Printer Manual de usuario
Xerox
Xerox Phaser 6180MFP Manual
Xerox
Xerox B1 Manual de usuario
Xerox
Xerox 8560DN - Phaser Color Solid Ink Printer Manual de usuario
Xerox
Xerox STACKER 8855/721P Manual de usuario
Xerox
Xerox Phaser 3600 Manual de usuario
Xerox
Xerox ECP- Magenta Toner Premix/Concentrate for ECP... Instrucciones de funcionamiento y mantenimiento
Xerox
Xerox 5500DN - Phaser B/W Laser Printer Manual de usuario
Xerox
Xerox C123 Copycentre Manual de usuario
Xerox
Xerox DocuColor 252 Instrucciones de montaje
Xerox
Xerox 6130N - Phaser Color Laser Printer Manual de usuario
Xerox
Xerox Synergix 8830 Manual de usuario
Xerox
Xerox Adaptive CMYK+ Kit Manual de usuario
Xerox
Xerox 5500DN - Phaser B/W Laser Printer Manual de usuario
Xerox
Xerox 3R11450 Manual de usuario
Xerox
Xerox Phaser 6180MFP Manual de usuario
Xerox
Xerox 6130N - Phaser Color Laser Printer Manual de usuario
