Watchguard AP430CR Instrucciones de instalación

WatchGuard AP430CR Hardware Guide

The WatchGuard AP430CR is a secure wireless access point designed for indoor/outdoor rugged deployment

conditions and built with an industrial-rated IP67 enclosure.

The AP430CR features a Wi-Fi 6 802.11ax 2x2 2.4 GHz dual radio and 4x4 5 GHz dual concurrent radio that

support up to 1148 Mbps data rate on the 2.4 GHz band and 2402 Mbps on the 5 GHz band.

The AP430CR also has a third 2x2 dual band radio for security scanning, and an integrated Bluetooth

(BLE)radio.

Power is provided by a PoE+ (Power over Ethernet) power source.

Access Point Management

You can manage WatchGuard Wi-Fi 6 access points with WatchGuard Cloud. WatchGuard Cloud delivers a

simpliﬁed platform for Wi-Fi management to easily deploy, conﬁgure, and report on your wireless networks.

For quick start instructions on how to set up your access point with WatchGuard Cloud, go to:

watchguard.com/start

About Your Hardware

Hardware Speciﬁcations

Processor Qualcomm Hawkeye IPQ8071A-1 Quad-core A53s @1.0GHz, Enterprise chip with

I-Temp support

Memory Flash: NOR Flash 8MB, NAND Flash 256MB

RAM: DDR4 512MB x 2

Radio Model 2.4 GHz Qualcomm Iron QCN5124-1 2x2 i-temp radio

5 GHz Qualcomm Iron QCN5154-1 4x4 i-temp radio

Scan radio: Qualcomm QCA9892 i-temp dual band 11ac 2x2 radio

Bluetooth: Qualcomm CSR8811A12 Bluetooth 4.0

Radio Type and

Frequency Band Radio 1: 2.4 GHz 2x2 802.11b/g/n/ax

Radio 2: 5 GHz 4x4 802.11a/n/ac/ax

Radio 3 (Scan):Dual band 802.11ac 2x2 radio

Antennas



Wi-Fi: 4 x 4/5dBi 2.4/5 GHz dual band N-type omnidirectional antennas

Scan Radio: 2 x 4/5dBi 2.4/5 GHz dual band N-type omnidirectional

antennas

BLE:1 x 4dBi 2.4 GHz external antenna

WatchGuard dual band omnidirectional dipole antennas (WG9004) are sold

separately in packs of two antennas.

Note:The device must have antennas connected for full range and functionality.

Wireless Security WPA3 PSK, WPA2 PSK, WPA3/WPA2 PSK, WPA3 Enterprise, WPA2 Enterprise,

OWA

Ethernet Interfaces 1 x 5 GbE Ethernet port (Aquantia AQR114C)

1 x GbE Ethernet port (QCA AR8033). This LAN 2 port is discontinued in

hardware revision Mand higher.

Power Interface PoE 54V DC 802.3at

Power Consumption 25.44W

Hardware Description

MTBF

(Mean Time Between

Failures)

275,523 hours

Dimensions 267.1 mm x 217.65 mm x 53.7 mm (10.5” x 8.6” x 2.1”)

Weight 1.759 kg (3.87 lbs)

Hardware Description

Environmental Requirements

To safely install your WatchGuard access point, we recommend that you:

Install the device per local regulations

Make sure the device has adequate clearance for air ﬂow and cooling

Other environmental requirements:

Operating Temperature -30°C to 60°C (-22°F to 140°F)

Operating Humidity 5% to 95% non-condensing

Non-operating Temperature -40°C to 85°C (-40°F to 185°F)

Non-operating Humidity 5% to 95%, non-condensing

Hardware Description

Bottom Panel Connections

2.4/5GHz

Antenna connectors for the dual band Wi-Fi radios.

2.4/5GHz Scan

Antenna connector for the dual band security scanning radio.

LAN 1 (POE+)

The LAN 1 port is a 5 GbE port that connects the access point to a wired LAN connection through a switch

or hub. This port also provides PoE+ (802.3at) power for the access point.

LAN 2

The LAN 2 port is a 1 GbE LAN port that you can use as a wired extension for an SSID network.

The LAN 2 port is discontinued in hardware revision Mand higher.

Reset Button

The reset button is located above the LAN 2 port. You must remove the weatherproof connector to

access the LAN2 port and the reset button.

The reset button and the LAN 2 port are discontinued in hardware revision Mand higher. You

can reset the access point from the command line interface (CLI). For more information, go to

Access Point Command Line Interface.

To reset the access point to factory-default settings:

Remove the weatherproof connector from the LAN 2 port.

Use a paper clip or other small object to press the reset button above the LAN 2 port.

Press and hold the reset button for up to 10 seconds. When you release the reset button, all LEDs will

go oﬀ to indicate that the access point has rebooted.

You can also reset the device from the access point command line interface (CLI). For more information,

go to AccessPoint Command Line Interface.

Top Panel Connections

5GHz/BLE

Antenna connector for the 5 GHz Wi-Fi and Bluetooth (BLE) radio.

2.4/5GHz Scan

Antenna connector for the dual band security scanning radio.

5GHz

Antenna connector for the 5 GHz Wi-Fi radio.

Side Panel Connections

LED Indicators

Wi-Fi in WatchGuard Cloud access points have LEDindicators that can show diﬀerent status conditions while

booting, activation validation, feature key download, WatchGuard Cloud device registration, and the connection

to WatchGuard Cloud.

The access point brieﬂy passes through each stage until the device is connected to WatchGuard Cloud and

shows a solid blue LEDindicator. If the access point remains in the same state for a long period of time without

a solid blue LED indicator status, there might be a network issue, activation or feature key issue, or a problem

with your WatchGuard Cloud account.

Check the following table for the status of the LEDindicators and how to troubleshoot the issue.

Solid Red or

Orange

Device is booting If the access point remains in this state, the access point processes

might not have started, or there might be an issue with the access

point ﬁrmware.

Disconnect and reconnect power to reboot the access point to

see whether the device connects.

Try to log in to the access point Web UI or command line

interface (CLI) to check the device status, current ﬁrmware

version, and run diagnostic tests. For more information, go to

Access Point Web UI or AccessPoint Command Line Interface.

Flashing Red

or Orange

(Fast:100

milliseconds)

Validate access

point activation

and download

feature key

If the access point remains in this state:

Make sure you have activated your access point with a valid

device serial number and license key in your WatchGuard

account. The license key must be for a WatchGuard Standard or

USP Wi-Fi license for Wi-Fi in WatchGuard Cloud.

Make sure the access point is connected to the network and has

received an IPaddress from DHCP.

Make sure the access point can connect to

*.watchguard.io

for

product activation and feature key updates.

LEDColor Status Troubleshooting

If you set up an access point behind a ﬁrewall that performs

inspection on HTTPS traﬃc, you must add

*.watchguard.io

the content inspection exception / bypass list to enable the

access point to receive a feature key from WatchGuard servers.

On the WatchGuard Firebox, this is enabled by default for cloud-

managed Fireboxes in WatchGuard Cloud.

Use the access point Web UI or command line interface (CLI) to

check the feature key status, download a feature key, and run

diagnostic tests. For more information, go to Access Point Web

UI or AccessPoint Command Line Interface.

Flashing Red

or Orange

(Medium: 500

milliseconds)

WatchGuard

Cloud device

registration

If the access point remains in this state:

Make sure access point can connect to

*.watchguard.com

for

WatchGuard Cloud device registration.

For service providers, make sure you have allocated the access

point from your inventory to a subscriber account. For more

information, see Access Point Allocation.

Make sure you have added the access point to your WatchGuard

Cloud subscriber account. For more information, see Add an

Access Point to WatchGuard Cloud

Flashing Red

or Orange

(Slow: 2

seconds)

Connection to

WatchGuard

Cloud servers

If the access point remains in this state:

Make sure the access point can connect to

*.watchguard.com

for WatchGuard Cloud management connections and is not

blocked by a ﬁrewall or other network device.

Make sure you do not have an expired MSSPlicense for the

access point.

Check the access point allocation status to see whether the

device was deallocated from the subscriber account.

Solid Blue Successfully

connected to

WatchGuard

Cloud

Device is online and connected to WatchGuard Cloud.

Flashing Blue Flash LED action

from WatchGuard

Cloud

LED ﬂashes blue for 60 seconds for identiﬁcation.

Flashing Blue

and Red

Access point failed

system integrity

check

If the device LEDs ﬂash alternating blue and red every second, the

device has failed a system integrity check and has rebooted in failsafe

mode. You must contact WatchGuard Support to replace the device.

LEDColor Status Troubleshooting

Mount and Connect the Access Point

Your package includes these wall mount and pole mount accessories:

2 x Pole mount clamps

4 x Wall mount screws

8 x Wall and pole mount screws

Ground screw

The MAC address and serial number of your access point are printed on a label on the back of

the device. Make sure you record this information before you mount the device.

Wall Mount Installation

Use the supplied wall-mounting accessories to install the access point on a wall.

1. Attach the access point to the wall mount bracket with the included screws.

2. Aﬃx the access point and mounting bracket to the wall with the included screws.

Otros manuales para AP430CR

Tabla de contenidos

Otros manuales de Punto de acceso inalámbrico de Watchguard

Watchguard

Watchguard AP332CR Manual de usuario

Watchguard

Watchguard AP420 Instrucciones de instalación

Watchguard

Watchguard AP225W Manual de usuario

Watchguard

Watchguard AP 320 Instrucciones de instalación

Watchguard

Watchguard AP225W Instrucciones de instalación

Watchguard

Watchguard AP225W Manual de usuario

Watchguard

Watchguard AP300 Instrucciones de instalación

Watchguard

Watchguard WatchGuard AP Series Manual de usuario

Watchguard

Watchguard AP330 Instrucciones de instalación

Watchguard

Watchguard AP130 Instrucciones de instalación

Watchguard

Watchguard AP 327 Series Manual de usuario

Watchguard

Watchguard AP432 Instrucciones de instalación

Watchguard

Watchguard AP 320 Manual de usuario

Watchguard

Watchguard AP325 Instrucciones de instalación

Watchguard

Watchguard AP430CR Instrucciones de instalación

Watchguard

Watchguard AP330 Manual de usuario

Watchguard

Watchguard AP100 Manual de usuario

Watchguard

Watchguard C-130 Manual de usuario

Watchguard

Watchguard AP100 Instrucciones de instalación

Watchguard

Watchguard AP330 Manual de usuario

Watchguard

Watchguard AP102 Instrucciones de instalación

Watchguard

Watchguard AP430CR Instrucciones de instalación

Watchguard

Watchguard AP 322 Instrucciones de instalación

Watchguard

Watchguard WGA15731 Instrucciones de instalación

Manuales populares de Punto de acceso inalámbrico de otras marcas

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manual de usuario

Ubiquiti

Ubiquiti NanoStation NSM2 Manual de usuario

Cisco

Cisco Aironet 1550 Series Manual de usuario

Aruba

Aruba IAP-335 Manual de usuario

Advantek Networks

Advantek Networks AWN-AP-54MR Manual de usuario

IP-COM

IP-COM AP355 Manual de usuario

Buffalo

Buffalo AirStation WLA-L11G Manual de usuario

EnGenius

EnGenius EnStationACv2 Manual de usuario

D-Link

D-Link DAP-3662 Manual de usuario

xG Technology

xG Technology xMax CN1300 Manual de usuario

Widelink

Widelink ezWave WAP-1100 Series Manual de usuario

Edimax

Edimax CAP1200 Manual de usuario

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manual de usuario

Aruba

Aruba AP-203R Manual de usuario

LuXout Shades

LuXout Shades LUXSHADE MOTION Manual de usuario

CreatComm

CreatComm TB5F Manual de usuario

SineDigital

SineDigital MW-1500AP(H) Manual de usuario

TP-Link

TP-Link AP9650 V1 Manual de usuario