Vitek VTC-IRV30/2810 Manual de usuario

black

VITEK

•1/3” Sony Super HAD II High Resolution Color CCD

•550 TV Lines of Resolution

•2.8~10mmm / F1.2 Varifocal Auto Iris Lens

•30 - 850nm IR LEDs with 100’ Range

•0 Lux Operation (IR LEDs On)

•IP-66 Rated Water Resistance

•Heavy Duty Mount with Cable Feed Through

•12VDC/24VAC Dual Voltage Operation

VTC-IRV30/2810

Day/Night IR Bullet Camera w/100’ Range

black

Table of contents

1. Safety instructions and Notes 3

2. General Descriptions and Features 4

3. Specifications 5

4. Supplied Items 6

5. Control and Part names 6

6. Installation 7-9

7. Power and Dimensional Drawings 10

To prevent fire or shock hazard, do not expose the unit to rain or moisture.

The symbol is intended to alert the user to the presence of important

operating and maintenance(servicing) instructions in the literature

accompanying the unit.

The symbol is intended to alert the user to the presence of

uninsulated "dangerous voltage" within the product's enclosure that

may be of sufficient magnitude to constitute a risk of electric shock

to persons.

WARNING

black

Warning(NTSC version) -- This equipment has been tested and found to comply with the limits for a Class A

digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses and can radiate radio frequency energy and if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation

of this equipment in a residential area may cause harmful interference in which case the user will be

required to correct the interference at his/her own expense.

Caution -- Any changes or modifications in construction of this device which are not expressly approved by

the party responsible for compliance could void the user's authority to operate the equipment.

1. Safety instructions, cleaning and Notes

• Please read these safety and operating instructions before placing the camera into operation.

• Keep the manual in a safe place for later reference.

• Pay attention to safety when laying the connection cable and observe that the cable is not

subjected to heavy loads, kinks or damage and that no moisture can penetrate.

• The unit may only be opened by authorized personnel.

• Never open the device and expose boards or lens. If repairs are undertaken by unauthorized

persons the Warranty will be void. If maintenance or repair is required, please call an authorized

service center.

• Use only a mild detergent to clean the housing.

• Keep the window surface clean from the dirt or dust, which may reflect the infrared light into the

lens at night.

Caution

To prevent electric shocks

and risk of fire hazards, do

NOT use other than specific

power source.

2. General Descriptions and Features

2-1. General Descriptions

This equipment is a weatherproof Day/Night color bullet camera with Sony Super HAD Ⅱ Color

CCD image sensor.

Including 30pcs LED,

- Possible to observe where no illumination is available at night.

- Up to 35Meters (100+’) for outdoor night observation distance.

Aluminum housing,

- Vandal Resistant Camera can be protected from a harsh environment.

Sunshield

- Camera can be protected from overheating in strong sun light.

With Hidden cable-through function

- Cable can be protected from vandalism

- Ease of installation

Dual Voltage 24VAC/12VDC power design,

- Offers flexibility of installation

- Ensures reliability

- Polarity free connection for power is allowed limiting the risk of short

2-2. Features

• 1/3” Super HAD Ⅱ Color CCD

• Resolution of 550TVL (day-time), 600TVL (night-time)

• Outdoor bullet style camera with Sunshield

• Enhanced sharpness compensation

• 0.05Lux light sensitivity

• Built-in Vari-focal Auto iris lens(2.8~10mm)

• Waterproof (IP66)

• Simple Focus adjustment

• Supply voltage: 24Vac or 12Vdc

• Hidden cable-through function

black

3. Specifications

Description

Image Device 1/3” Sony SuperHAD II Color CCD

Effective Pixels 768 x 494 (NTSC) / 752 x 582 (PAL)

Resolution 550TVL (Day) / 600TVL (Night)

Sensitivity 0.05Lux(F1.2@40IRE), 0Lux with built-in 30 Infrared LEDs

S/N ratio More than 50dB with AGC off at 50IRE

Electronic Iris 1/60 – 1/100,000sec (NTSC) 1/50 – 1/100,000sec (PAL)

White Balance 3,000°K – 8,000°K Automatic tracking

BLC Built-in, Factory set to ON

Video Output VBS 1.0Vpp +/-10%, 75ohm

Built-in Lens 1/3" Vari-Focal, f=2.8-10.0mm, F1.2, DC Auto Iris

Infrared LEDs 30pcs @ 850nm

IR Distance 35M (110’)

Operation Power 24Vac(20~28.8Vac) or 12Vdc (11.5~30Vdc), 5Watts max

Cable length 5’ (1.5M)

Operating Conditions 14 – 122 degrees F (-10°C - +50°C), 85% RH Max. (non-condensing)

Dimensions (Dia. x H) 2.68” x 8.66” (68mm x 220mm)

Net Weight 1.21 lbs (550g)

4. Supplied Items

①1 x Weatherproof D/N Bullet Camera

②3 x Mounting screws

③3 x anchors

④1 x 2.5mm L-Wrench

⑤1 x Installation and Operating Instructions

5. Control and Part names

5-1. External

5-2. Internal

ⓐ

ⓔ

ⓓⓒ

ⓑ

ⓐWindow

ⓑSunshield

ⓒLock screw for Sunshield

ⓓFront cover

ⓔBody

ⓕLocking screw for radius

ⓖLocking screw for Tilt-direction

ⓗLocking screw for Pan-direction

ⓘMounting Base

ⓙRubber seal

②

③

④

ⓚInfrared LEDs (X30)

ⓛLens Hood

ⓜZoom adjustment knob

ⓝFocus adjustment ring

ⓕⓖ

ⓚⓛⓜⓝ

ⓗ ⓘ

ⓙ

black

5-3. Iris adjustment and Function switches on the Board.

S/W Function Default ON OFF

1 ELC OFF

ELC mode.

Linear electronic shutter is

operating.

ALC Mode.

Set to OFF for auto iris lens

function.

2 BLC OFF

Back light compensation is

enabled and operating

automatically.

Back light compensation is

disabled.

3 FL OFF

Flickerless mode ON.

Electronic shutter is fixed to

1/100sec (NTSC).

Flickerless mode OFF.

Electronic shutter mode follows

ELC/ALC.

4 N/A OFF N/A N/A

6. Installation

• Make sure the power is removed before installation.

6-1. Procedure of installation

1) Locate at the installation position and drill 3 holes for ⓘMount base on the wall.

Use MOUNTING TEMPLATE printed on the bottom of the inner packing material as shown in

below drawing.

2) Route the power/ video cable from the camera to the monitor

location and power outlet.

Care should be taken not to damage, kink or expose the cable

to a hazardous environment.

Iris Low Iris High

3) Place camera on a pre-drilled position and fix it by

using ②Mounting screws.

6-2. Setup of ZOOM and FOCUS

•Adjust zoom and focus in order.

1) Open ⓓFront cover for adjustment.

2) Place the separated ⓓFront cover in a safe place away from water & dust.

3) Turn ⓜZoom knob CCW slightly to unlock the knob.

4) Adjust ⓜZoom knob to set the zoom or field of view. (Wide Tele)

5) Turn ⓜZoom knob CW slightly to lock the knob.

6) Using your thumb and index finger, turn ⓝFocus ring to set the focus. (Far Near)

7) Close and tighten ⓓFront cover. (See CAUTION below)

4) Adjust the camera direction as in below

steps.

Direction I: Adjust the camera direction with

ⓗscrew for Pan-direction.

Direction II: Adjust the camera direction with

ⓖscrew for Tilt-direction.

Direction III: Adjust the camera direction with

ⓕscrew for radius.

Ⅲ

Ⅱ

Ⅰ

ⓕ

ⓖ

ⓗ

)

& 5

)

& 6

)

ⓜFocus Ring

ⓛZoom Knob

black

6-3. Sunshield

Camera can be protected from the heat of strong sun light by its Sun shield.

Sunshield must be tightened to the body to avoid detaching by wind.

When the sunshield is properly installed on the

Camera body the ⓒLock screw for Sunshield

should be located in the center of the screw

hole.

The sunshield may be adjusted back or forth

according to the wide or telephoto position of

the lens.

If shades by the sunshield are seen on the

image you may reverse the sunshield direction

backside to front.

* IMPORTANT TIP for

roper focus adjustmen

Step 1. Turn Iris Level adjustment VR clockwise to max position.

Step 2. Set ELC switch to ON at DIP switches.

Step 3. Adjust zoom knob and focus ring of lens.

Ste

4. Set ELC switch to OFF at DIP switches.

CAUTION

When assembling ⓓFront cover, be sure

that ⓙRubber sealing is not protrusive.

If ⓓFront cover is tightened excessively,

sealing may not be ensured.

ⓓFront cover

6-4. Power connector

Camera can be operated with either 24VAC or 12VDC.

Polarity free connection is acceptable, but follow the indication if possible.

6-5. Powering sequence

Make sure the power is removed before the installation.

Follow the order for applying power.

Connect the low voltage section (12VDC or 24VAC) first then plug the AC adapter into the AC

outlet to avoid an improper reset from power jitter and damage from the surge voltage after

load.

7. Dimensional Drawings

(Units in mm)

Otros manuales para VTC-IRV30/2810

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vitek

Vitek

Vitek VTC-LED667CB Manual de usuario

Vitek

Vitek VTD-C14 Manual de usuario

Vitek

Vitek VTD-C13A Manual de usuario

Vitek

Vitek VTD-M2HET2812 Manual de usuario

Vitek

Vitek VTD-TND5RFS-2 Manual de usuario

Vitek

Vitek VTD-IR2811DN Manual de usuario

Vitek

Vitek VTC-C680 Manual de usuario

Vitek

Vitek VTD-MD5CH Manual de usuario

Vitek

Vitek VTD-MV-VN Manual de usuario

Vitek

Vitek VTC-TTT28R2F Manual de usuario

Vitek

Vitek VT-PTZ220N Manual de usuario

Vitek

Vitek Transcendent VTC-TNB8RMA4 Manual de usuario

Vitek

Vitek TRANSCENDENT VTD-T4D6HR5MD Manual de usuario

Vitek

Vitek VTD-TTAD24R2F Manual de usuario

Vitek

Vitek VTD-TND4RFA4 Manual de usuario

Vitek

Vitek VTD-B72 Manual de usuario

Vitek

Vitek Transcendent 3 Series Manual de usuario

Vitek

Vitek VTD-THD5R3 Manual de usuario

Vitek

Vitek TRANSCENDENT VTC-THT10R2F Manual de usuario

Vitek

Vitek VTC-LED697HRCB Manual de usuario

Vitek

Vitek VTD-C410 Manual de usuario

Vitek

Vitek VTC-MV2NZ Manual de usuario

Vitek

Vitek VTC-IRLED24A Manual de usuario

Vitek

Vitek VTC-C2NZ Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario