Vitek Transcendent VTD-TND6FPN Manual de usuario
VITEK
VITEK
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads
VTD-TND6FPN
Transcendent Series 6
Megapixel H.265 IP Vandal 360°
Fisheye Camera with IR LEDs
QUICK START GUIDE
FEATURES
• NDAA Compliant
• 1/2.9” 6.0 MegaPixel CMOS Image Sensor
• Up to 30fps live view @ 6 MegaPixel
• 1.1mm @F2.0 Fisheye Lens with 180° Horizontal FOV:
180° (desktop) / 360° (ceiling)
• 6 High Power Covert IR LEDs with up to 100’ IR Range
• True Mechanical Day/Night function by ICR
• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction
• ROI Encoding
• H.265/H.264/MJPEG Triple Streaming
• Secondary Video Output (CVBS)
• Remote Viewing via CMS, Internet Explorer, and iOS & Android Apps
• ONVIF Compliant
• MicroSD memory card slot for Local recording supporting up to 256GB
• IK10 + IP67 Ingress protection
• Two Way Audio + Built-in Mic, Alarm In / Out
• 12VDC & PoE (Power over Ethernet) Operation
• Available with Optional J-Box VT-TJB-F1, Pendant Mount VT-TPDM-F,
and Wall Mount VT-TWM-F (See page 11)
• 3-Year Warranty
2
Overview
Components and Accessories
Camera
Quick Guide
Screws
Hex Wrench
Drill Template
Plastic Wall Anchors
Waterproof Cap
RJ-45 Ethernet
Audio In
Audio Out
CVBS Output
Alarm I/O
RS-485
Power Cable
MicroSD Card Slot
Reset
1
2
3
4
5
6
7
8
9
1
3
4
5
6
7
2
8
9
3
Network Cable & Power Connections
First connect the Water Resistant Cap to an Ethernet patch cable, then
connect the cameras ethernet adaptor. If not powering the camera with
PoE, also connect the power Cable to an approved 12VDC Power
Supply.
Weather Resistant Network Coupler
1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.
ALM-COM
ALM-OPEN
ALM-INA
ALM-GND
RS485T+
RS485T-
12VDC
Optional 12VDC
Power Connection.
Not needed with PoE
4
SD Card Installation
Gap
Fixed Ring
1. Remove the fixed ring from the camera.
2. Loosen the screws of the cover of the SD card and then insert
the SD card. Then reinstall the cover ring.
5
Installation
Before beginning installation, make sure that the wall or ceiling is
strong enough to withstand 3 times the weight of the camera. The
mounting steps are as follows:
1. Remove the fixed ring
from the gap of the
camera (see Install SD
Card)
2. Drill the screw holes and
the cable hole on the
wall according to the
drill template.
3. Route and connect the
cables.
4. Fix the camera to the
wall with screws as
shown.
5. Install the fixed ring
back onto the camera.
∅5.12”
∅0.18”
3.31”
3.82”
6
LAN Configuration
The camera can be accessed on the local network either using the
IP-Tool or directly in a web browser.
Accessing the Camera Using the IP-Tool
1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer on the included Product Documentation
CD, then install on the PC. Open the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201.
Click the information of the camera listed in the above table to show
the network information on the right side. Modify the IP address and
gateway of the camera and make sure its network address is in the
same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer
is 192.168.13.4. So the IP address of the
camera shall be changed to 192.168.13.X.
After modification, please input the password
of the administrator and click “Modify” button
to modify the setting.
** Default admin password: “123456".
7
4. Double-click the IP address and then the system will pop up the web
browser to connect IP-CAM . IE browser will download the Active X
control automatically. After downloading, a login window will pop up
as shown below:
Input the user name and password to log in.
Default user name: admin / Default password: 123456.
Directly Access Through a Web Browser
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP: 80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for
the first time.
1. Manually set the IP address of the PC and the network segment
should be as the same as the default settings of IP-CAM. Open the
network and share center. Click “Local Area Connection” to pop up
the following window.
Select “Properties” and then select Internet protocol according to the
actual situation (for example: IPV4). Next, click “Properties” button to
set the network of the PC.
8
2. Open the IE Browser and input the default address of IP-CAM and
confirm. The IE browser will download Active X control automatical-
ly.
3. After downloading Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.
WAN Configuration
Access the camera by the router or virtual server for example.
1. Make sure the camera is connected to the LAN; Then log into the
camera via LAN and go to System Congfig→Network Config→Port
menu to set up the port number.
2. Enter System Config→Network Config→IP Address menu to modify
the IP address.
4. Open the web browser and input its WAN IP and HTTP port to
access the IP-CAM.
3. Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.
9
Image Sensor
NDAA Compliant
Electronic Shutter
Lens
IR LEDs
IR Distance
Day & Night
WDR
BLC
DNR
Slow Shutter
Video Compression
Encoding Type
Smart Encoding
Video Bit Rate
Audio Compression
Main Stream Max. Frame Rate
Max. Image Size
Image Settings
Network
Video Output
Audio
RS485
Alarm
Remote Monitoring
Online Connection
Network Protocol
Interface Protocol
Storage
Smart Alarm
PoE
Ingress Protection / Impact
Power Supply
Power Consumption
Operating Environment
Weight, Dimensions
1/2.9” 6.0 MegaPixel CMOS Image Sensor
Yes
1/25 s ~ 1/100000 s
1.1mm @ F2.5, horizontal field of view: 180° (wall mounting) 360° (ceiling mounting)
6 High Power Covert IR LEDs
100’ IR Range
True Day/Night by ICR
Digital WDR (D-WDR)
Yes
XD-DNR (2D-DNR + 3D-DNR)
Yes
H.265 / H.264 / MJPEG
VBR (five levels adjustable) / CBR
Support low bitrate, low delay; support ROI coding & SVC technology; support self-adaptive transmission bitrate as the network environment
256 Kbps ~ 10Mbps
G.711A /G. 711Mu
Fisheye / Panorama+3 PTZ: 30fps @ (2160×2160, 1920×1920, 1440×1440), 30fps @ (1920×1080), 30fps @ (960×540)
2160 x 2160 Pixels
ROI, Saturation, Brightness, Chroma, Contrast, Wide Dynamic, Sharpen, NR,etc. adjustable through client software or web browser
RJ45
CVBS video output (BNC × 1)
1 Ch. In + Out + Built-In Mic*
Yes
1 CH alarm input; 1 CH alarm output
IE browsing, CMS remote control
Support simultaneous monitoring for up to 10 users; Support multi-stream real time transmission
TCP / IP, UDP, DHCP, NTP, RTSP, PPPoE, DDNS, SMTP, FTP
ONVIF, GB-T/28181-2011
MicroSD Card for local storage (up to 256GB) / Network remote storage
Motion Detection, IP address conflict, SD card error, SD card full, IO alarm, cable disconnection
Yes
IP67 / IK10 Impact
12VDC / PoE (Dual Voltage)
<12W
14ºF~122ºF (-10º~50ºC) / 10~90% RH
15.24oz. / 0.95oz. / 432g, 1.61” × 5.12” (41 × 130mm)
Detailed Specifications VTD-TND6FPN
10
OPTIONAL ACCESSORIES
AND RELATED PRODUCTS FOR
TRANSCENDENT IP CAMERAS
VT-TNR3216PF
VT-TNR818PF
VT-TNR1646PF
• 8MP (4K) HDMI Output
• H.265 / H.264 Compression
• Full Analytic Support Including
Face Detection
• 360 Degree / Fisheye De-Warping
• Available in 8, 16, and 32 Channels
• Up to 96TB Depending on Model
• PoE Support on ALL Models
ADVANCED LEARNING NVRs
A Standalone
Solution with FULL
Analytic Support
Tabla de contenidos
Otros manuales de Cámara de seguridad de Vitek
Vitek
Vitek TRANSCENDENT VTC-TNB3RFE-2 Manual de usuario
Vitek
Vitek VT-PTZ36W Manual
Vitek
Vitek VTC-TNT5RFE-2 Manual de usuario
Vitek
Vitek Mighty VTD-MP1850DN Manual de usuario
Vitek
Vitek VTC-LED307BB Manual de usuario
Vitek
Vitek VTC-LED697HRCB Manual de usuario
Vitek
Vitek Transcendent VTC-TNB8RFS-2 Manual de usuario
Vitek
Vitek VTD-A4F Manual de usuario
Vitek
Vitek Transcendent Series Manual de usuario
Vitek
Vitek VT-IR1C/24 Manual de usuario
Vitek
Vitek VT-IR1C/12 Manual de usuario
Vitek
Vitek Transcendent VTC-TNB5RME Manual de usuario
Vitek
Vitek VTC-IRV30/2810 Manual de usuario
Vitek
Vitek VTD-MH2910 Manual de usuario
Vitek
Vitek VTC-EL52H Manual de usuario
Vitek
Vitek VTD-A4F/IB Manual de usuario
Vitek
Vitek Transcendent VTD-TND4FLN-2 Manual de usuario
Vitek
Vitek VT-PTZ220N Manual de usuario
Vitek
Vitek VTC-IRLED30HD Manual de usuario
Vitek
Vitek Virtuoso Series Manual de usuario
