Vitek TRANSCENDENT VTC-TNB48R4M2 Manual de usuario

VITEK

VTC-TNB48R4M2

VTC-TNB48R5V2

5.0 Megapixel Indoor/Outdoor

WDR IP IR Bullet Cameras

QUICK START GUIDE

FEATURES

• Megapixel Progressive Scan CMOS image sensor

• Advanced Starlight Technology Offers Dramatically Higher

Sensitivity to Light Producing Color Images in Very Dark & Night

Scenes

• Up to 30fps live view

• 3.6~10mm Varifocal Lens (VTC-TNB48R5V2) / Motorized 3.3-

12mm Motorized Varifocal Lens (VTC-TNB48R4M2)

• 48 Infrared LED’s with 160’ IR Range

• Digital Wide Dynamic Range (D-WDR)

• True Mechanical Day/Night function by ICR

• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction

• On Board Motion Detection

• H.265/H.264/MJPEG Triple Streaming

• Secondary Video Output (CVBS)

• MicroSD memory card slot for Local recording supporting up to

128GB MicroSDXC cards

• Remote Viewing via CMS, Internet Explorer, and iOS & Android

Apps

• Minimal Latency with up to 10 simultaneous user connections

• ONVIF Compliant

• IP66 Weather Resistance

• Optional Junction Box Mount Available (VT-TJB01)

• 12VDC & PoE (Power over Ethernet) Operation

PLEASE NOTE:

Complete User Guide, Software, Tools, and Updates are

available online. Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

2 3

Components and Accessories

Overview

Camera

Quick Guide

Screws

Hex Wrench

Drill Template

Rubber Plug

Waterproof Cap

Service Port Cable

*VTC-TNB48R5V2 Only

RJ-45 Ethernet

Audio In

Audio Out

CVBS Output

Alarm I/O

RS-485

Power Cable

Zoom*

Focus*

Reset

Service Port

MicroSD Card Slot

Cable Connections

Weather Resistant Network Coupler

First connect the Waterproof Cap to an Ethernet patch cable, then

connect the cameras ethernet adaptor. If not powering the camera with

PoE, also connect the power Cable to an approved 12VDC Power

Supply.

1. Loosen the nut from the Weather Resistant Network Coupler,

2. Run ethernet cable through coupler, then attach a RJ-45 connector.

3. Tighten the nut and coupler for a weather resistant seal.

Network Cable

Optional 12VDC

Power Connection.

Not needed with PoE

ALM: COM

ALM: NO

ALM: IN

ALM: GND

RS-485 +

RS-485 -

4 5

Installation

Before beginning installation, make sure that the wall or ceiling is

strong enough to withstand 3 times the weight of the camera. The

mounting steps are as follows:

1. Attach the drill template to

the place where you want to

install the camera, then drill

4 screw holes and 1 cable

hole (if you want to route the

cables through the mounting

base) according to the drill

template

2. Route the cables and connect the power & video cables, use the

rubber plug to fill the gap of the mounting base. then secure the

mounting base to the ceiling or wall with screws.

Rubber Plug

Mount Base

Installation

3. Loosen the mount lock to adjust the Pan and Tilt of the camera, then

tighten the mount lock to secure the viewing angle adjustments.

4. To adjust the lens, start by removing the Lens Cover, then adjust

the Focus and Zoom levers to achieve a clear image. Replace

the Lens Cover. *VTC-TNB48R5V2 Only

5. Carefully remove the protective film from the lens to complete the

installation.

90° Tilt

360° Pan

Zoom

Focus

Lens Cover

6 7

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

1. Attach the drill template to the place where you want to install the

camera, then drill 3 screw holes and 1 cable hole (if you want to

route the cables through the mounting base) according to the drill

template

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer on the included Product Documentation

CD, then install on the PC. Open the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

4. Double-click the IP address and then the system will pop up the web

browser to connect IP-CAM . IE browser will download the Active X

control automatically. After downloading, a login window will pop up

as shown below:

Input the user name and password to log in.

Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP: 80

Subnet Mask: 255.255.255.0 Data Port: 9008

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for

the first time.

1. Manually set the IP address of the PC and the network segment

should be as the same as the default settings of IP-CAM. Open the

network and share center. Click “Local Area Connection” to pop up

the following window.

Select “Properties” and then select Internet protocol according to the

actual situation (for example: IPV4). Next, click “Properties” button to

set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and

confirm. The IE browser will download Active X control automatical-

ly.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

camera via LAN and go to System Congfig→Network Config→Port

menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to modify

the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vitek

Vitek

Vitek VTC-LED667CB Manual de usuario

Vitek

Vitek VTC-HOCRBD2812 Manual de usuario

Vitek

Vitek VTC-BHOC6R4F Manual de usuario

Vitek

Vitek VTD-TNMD4RFS Manual de usuario

Vitek

Vitek VTD-VH49VP4 Manual de usuario

Vitek

Vitek VTC-C2NZ Manual de usuario

Vitek

Vitek VTC-T4T3HR2MD Manual de usuario

Vitek

Vitek VTC-IRLED30A Manual de usuario

Vitek

Vitek VTC-THB8R2 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Vitek

Vitek VTC-IRLED24H Manual de usuario

Vitek

Vitek Transcendent VTC-TNB2LPR Manual de usuario

Vitek

Vitek VT-TPTZ10HR-4N Manual de usuario

Vitek

Vitek VTC-TNB4MADW Manual de usuario

Vitek

Vitek VTD-THD5R3 Manual de usuario

Vitek

Vitek VTC-IRE30 Manual de usuario

Vitek

Vitek TRANSCENDENT VT-SMKC2T Manual de usuario

Vitek

Vitek VT-TPTZ25HRAN-4PNS Manual de usuario

Vitek

Vitek TRANSCENDENT VTC-TNB42R5F2 Manual de usuario

Vitek

Vitek VTC-THB5R3 Manual de usuario

Vitek

Vitek VTC-C574 Manual de usuario

Vitek

Vitek VTC-T4B4HR5MD Manual de usuario

Vitek

Vitek VTC-TNT4RMS Manual de usuario

Vitek

Vitek VTC-IRA70/650 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Vicon

Vicon V662-D-1 Instrucciones de funcionamiento

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario