Vicon HPOE-100 Manual de usuario

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vicon

Vicon

Vicon V920B-A Series Manual de usuario

Vicon

Vicon SN118C Manual de usuario

Vicon

Vicon Surveyor MKII Series XX282-40-01 Guía rápida

Vicon

Vicon Vantage V16 Manual de usuario

Vicon

Vicon SVFT-PRS22E Manual de usuario

Vicon

Vicon V962B-IR922M Manual de usuario

Vicon

Vicon IX 4000 L Manual de usuario

Vicon

Vicon XX235-01-01 Instrucciones de funcionamiento

Vicon

Vicon Surveyor 99 Manual del propietario

Vicon

Vicon V700-C Series Manual de usuario

Vicon

Vicon V960D Series Manual de usuario

Vicon

Vicon Roughneck V920D Series Manual de usuario

Vicon

Vicon CE102B Manual de usuario

Vicon

Vicon surveyor 1000 Manual de usuario

Vicon

Vicon V9360-6 Series Manual de usuario

Vicon

Vicon V992D-N4 Manual de instrucciones

Vicon

Vicon CE102D Manual de usuario

Vicon

Vicon VC367DSP Manual de usuario

Vicon

Vicon V8360W Series Manual de usuario

Vicon

Vicon VC275-24 Guía del usuario

Vicon

Vicon V840D Series Manual de usuario

Vicon

Vicon SurveyorVF SVFT-M Manual de usuario

Vicon

Vicon V9360-6 Series Instrucciones de funcionamiento

Vicon

Vicon SurveyorVFT SVFT-C266M Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario

HPOE-100

Network Camera Housing

INSTALLATION GUIDE

1.

Mounting Configuration and Dimensions

2.

Component Description

1

January 2016

3.

Power Consumption

D-Fog Heater

Always On (9W)

Heater

15°C On, 25°C Off (10W)

IR LEDs

3W

4.

Installation Recommendations

If you plan to install this camera enclosure into a tropical, sea coastal, or an environment where salt

water or corrosive industrial waste water/moist are present, please seal each stainless steel screws

and fittings with a silicon grease compounds. This will help prevent electrolysis to occur and extend

the life span of the camera and housing.

5.

Installation

A.

Prepare a CAT5e Ethernet cable. Pass it through the waterproofconnectors.

B.

You may need to remove the RJ45 connector, and use a crimping tool to connect the

Ethernet wires to an RJ45 connector inside the enclosure. Use an Ethernet cable ofthe

width of 5 ~ 6.5mm.

2

January 2016

C.

When done, tighten up the waterproof connectors.

D.

Align the buffer pad with the mounting hole at the bottom of the camera

E.

Place the mounting plate on top of buffer pad and then secure it to the camera. You may need

adjust its position so that the lens module can flush align with the tempered glass.

F.

Secure the camera to the enclosure by securing screws through the keyholeslots.

3

January 2016

G.

Connect PoE input to the power unit. Connect a short Ethernet cable between thePoE

output and the Ethernet port on the camera. If using the media converter, connect the

wires to the 12V output on the PSU unit.

H.

Connect the day/night signal lines from the IR unit to the relay connectors on the

camera's terminal block. The day/night mode relay connection enables the

synchronization of IR light and the automated day/night switching mechanism onthe

camera.

I.

Having the wiring done inside the enclosure, you can install the enclosure bracket to a

preferred location at your installation site. Drill mounting holes and a cable routing hole(if

preferred) on a wall. Install the bracket.

J.

Lift the whole enclosure up to the installation position, and pass the Ethernetcable

through the bracket.

PoEINfrom

external

PoEOUTto

12VDCOUT

12Vpowertothe

4

K.

Mount the enclosure on to the installed bracket, and secure the connection bytightening

the 4 socket screws. Due to the weight of the enclosure, it is best to have two men

mounting the enclosure.

January 2016

5

Vicon Industries Ltd

www.vicon-security.com

6

January 2016