Vicon V9360-6 Series Manual de usuario

XX289-10-02

User Guide

V9360-6 and V9360-12 Series

Network Panoramic Cameras

Vicon Industries Inc. does not warrant that the functions contained in this equipment will

meet your requirements or that the operation will be entirely error free or perform

precisely as described in the documentation. This system has not been designed to be

used in life-critical situations and must not be used for this purpose.

Document Number: 8009-8289-10-02 Product specifications subject to change without

Vicon Industries Inc.

Tel: 631-952-2288) Fax: 631-951-2288

Toll Free: 800-645-9116

24-Hour Technical Support: 800-34-VICON

(800-348-4266) UK: 44/(0) 1489-566300

www.vicon-security.com

Table of Contents

1. Overview................................................................................................................................2

1.1 Features......................................................................................................................2

1.2 Package Contents .......................................................................................................3

1.3 Dimensions..................................................................................................................5

1.4 Connectors (Indoor Only).............................................................................................6

1.5 Function Cables (Outdoor Only) ..................................................................................7

2. Camera Cabling.....................................................................................................................8

2.1 Power Connection .......................................................................................................8

2.2 Ethernet Cable Connection..........................................................................................8

2.3 Connect Alarm I/O.......................................................................................................8

2.4 Waterproof Cable Connector (Outdoor Only)...............................................................9

2.5 Camera Installation....................................................................................................11

3. System Requirements ........................................................................................................12

4. Access Camera ...................................................................................................................13

5. Setup Video Resolution......................................................................................................17

6. Configuration Files Export / Import ...................................................................................18

7. Tech Support Information ..................................................................................................19

7.1 Delete the Existing DCViewer....................................................................................19

7.2 Setup Internet Security..............................................................................................20

Appendix: Technical Specifications

Caution: Risk of Explosion if battery is replace by incorrect type. Dispose of used batteries

according to the instructions.

The unit and all interconnected equipment must be installed indoorswithin the same building,

including all PoE-powered network connections, as described by Environment A of the IEEE

802.3af standard.

1. Overview

The V9360-6 and V9360-12 Series Panoramic IP Cameras are a high resolution

surveillance solution that features 360° wide coverage without blind spots. The

panoramic camera supports resolution up to 12 megapixels streaming at 20 fps,

which allows the videos to be viewed smoothly. Moreover, the panoramic camera

supports digital PTZ, panoramic view and several display modes to fulfill users’

needs. With the compact and concise design, the V9360 series is suitable for

many kinds of environments, such as office rooms, hotels, vehicles, etc.

Additionally, the embedded edge dewarping engine enables the panoramic

camera to dewarp images by the camera rather than the backend system.

Therefore, the edge dewarping technique reduces the burden of the backend

system and also enhances the flexibility of usage. Featuring IR LED module and

Smart Picture Quality/Noise Reduction improves the image quality in low light

environments.

Refer to Vicon’s website, www.vicon-security.com, to assure you are using the most

current documentation and software for the Camera

1.1 Features

Progressive Scan CMOS Sensor

Backend Dewarping- up to 12M Resolution

Edge Dewarping- up to 4M Resolution Real-time

Quad Streams Compression- H.264 Baseline / Main / High Profile + MJPEG

Multiple Dewarp Display Modes- Digital PTZ / Panorama View / Quad View

Smart Event Functions -

Motion Detection / Network Failure Detection / Tampering Alarm / Periodical

Event / Manual Trigger Event / Audio Detection

Multiple and Dynamic Region of Interest (ROI) Windows

Smart Text Overlay and Privacy Masks

Day / Night (ICR)

IR LED Module

Built-in Microphone & Speaker (indoor only)

2D/3D Noise Reduction / Color Noise Reduction

Weatherproof (IP66 International; outdoor only))*

microSD and NAS Recording Support

Compact and Concise Design

ONVIF Support

IK10

1.2 Package Contents

Please check that the package contains the items listed below.

Indoor

V9360-6 or V9360-12

IP Camera

Self-Tapping Screw (x3)

Plastic Anchor (x3)

Security Torx

Power Terminal Block

Quick Guide

NOTE: The supplied self-tapping screws are for soft substances /

materials such as wood. For other installation environments such as

cement wall, users MUST pre-drill and use plastic anchors before

fastening the supplied self-tapping screws on the wall.

NOTE: To purchase power adaptor, please contact the camera

manufacturer for further information.

Outdoor

V9360W-6 or V9360W-12

IP Camera

Self-Tapping Screw

(x3)

Plastic Anchor

(x3)

Security Torx

Power

Terminal Block

Alarm I/O

Terminal Block

Quick Guide

NOTE: The supplied self-tapping screws are for soft substances /

materials such as wood. For other installation environments such as

cement wall, users MUST pre-drill and use plastic anchors before

fastening the supplied self-tapping screws on the wall.

NOTE: To purchase power adaptor, please contact the camera

manufacturer for further information.

1.3 Dimensions

The dimensions of the camera are shown below.

1.4 Connectors (Indoor Only)

Loosen the security screws and open the cover to access the connectors.

The diagram below shows the connectors of the camera. Each connector is

defined as follows.

No.

Connector

Definition

Remarks

Power

12 VDC

Power connection

Reserved

RJ-45

For network and PoE connections

microSD Card Slot

Insert the microSD card into the card slot to store

videos and snapshots. Do not remove the

microSD card when the camera is powered on.

Alarm & Audio I/O

Alarm Out +

Alarm connection

Alarm Out -

Alarm In +

Alarm In -

GND

Ground connection

Audio Out

Two-way audio transmission

Audio In

Built-in Microphone

Audio In

Default Button

Press the button with a proper tool for at least 20

seconds to restore the system.

Speaker

Audio Out

NOTE: It is not recommended to record with the microSD card for 24/7

continuously, as it may not be able to support long term continuous data

read/write. Please contact the manufacturer of the microSD card for

information regarding the reliability and the life expectancy.

1.5 Function Cables (Outdoor Only)

No.

Connector

Definition

Remarks

Audio I/O

Pink

Audio In

Two-way audio transmission

Green

Audio Out

Power (12 VDC)

(2-Pin Terminal Block)

Black

12 VDC –

Power connection

Red

12 VDC +

Alarm I/O

(4-Pin Terminal Block)

Alarm In –

Alarm connection

Alarm In +

Alarm Out –

Alarm Out +

GND

Ground connection

RJ-45

For network and PoE connections

Default Button

Refer to the Default Button in the table

under Connectors (Indoor Only).

microSD Card Slot

Refer to the microSD Card Slot in the table

under Connectors (Indoor Only).

2. Camera Cabling

Follow the instructions below to complete the cable connections.

2.1 Power Connection

For power connection, refer to section Connectors (Indoor Only) for the indoor

models, and see section All in One Cable (Outdoor Only) for the outdoor models.

Alternatively, users can power the camera by PoE if a Power Sourcing

Equipment (PSE) switch is available. Refer to the section below for Ethernet

cable connection.

NOTE: If PoE is used, make sure PSE is in use in the network.

2.2 Ethernet Cable Connection

To have the best transmission quality, cable length should not exceed

100 meters. Connect one end of the Ethernet cable to the RJ-45 connector of

the camera and plug the other end of the cable to the network switch or PC.

NOTE: In some cases, Ethernet crossover cable might be needed when

connecting the camera directly to the PC.

Check the status of the link indicator and the activity indicator LEDs. If the LEDs

are unlit, please check the LAN connection.

Green Link Light indicates good network connection.

Orange Activity Light flashes for network activity indication.

2.3 Connect Alarm I/O

The camera supports one alarm input and one relay output for alarm application.

Refer to Connectors section for pin definitions.

NOTE: Do NOT connect external power supply to the alarm I/O

connector of the IP camera.

2.4 Waterproof Cable Connector (Outdoor Only)

Follow the instructions below to waterproof the connectors of the different types

of cables. The supported cables are as shown below.

All-in-One Cable

IP66 RJ-45 Cable

All-in-One Cable

Follow the steps below to waterproof the connectors of the All-in-One cable.

Step 1:

Connect the required devices to the All-in-

One cable and coat the joints with silicone gel.

There should be no gap between the

connectors and the cables. For the alarm I/O

connector and the power connector, make

sure the side with wires attached is also

sealed with silicone gel.

In addition, attach the ground cable to the

ground and wrap the wires with silicone gel.

Make sure the wires are not exposed to the

air.

Step 2:

Seal the end of the rubber coating of the All-

in-One cable as indicated in the figure on the

right. Be sure to use enough silicone gel to fill

in the hose and wrap around each wire;

otherwise, waterproof function cannot be

guaranteed.

Otros manuales para V9360-6 Series

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vicon

Vicon

Vicon SurveyorVFT SVFT-M Manual de usuario

Vicon

Vicon V661-N-1 Series Instrucciones de funcionamiento

Vicon

Vicon V960D-N312M Manual de instrucciones

Vicon

Vicon Cruiser SN660V Instrucciones de funcionamiento

Vicon

Vicon Roughneck AI V2000D Series Manual de usuario

Vicon

Vicon Cruiser SN663V-B-EX Instrucciones de funcionamiento

Vicon

Vicon Roughneck V920D Series Manual de usuario

Vicon

Vicon IX 2000 L Manual de usuario

Vicon

Vicon VC-700W Manual de usuario

Vicon

Vicon Surveyor 282-00-02 Series Manual de usuario

Vicon

Vicon ROUGHNECK V-CELL-HD-B Manual de usuario

Vicon

Vicon Roughneck AI V2000D Series Manual de usuario

Vicon

Vicon Roughneck V2100B Series Manual de usuario

Vicon

Vicon XX247-32-00 Manual de usuario

Vicon

Vicon V9360-6 Series Instrucciones de funcionamiento

Vicon

Vicon VC5050-DSP Manual de usuario

Vicon

Vicon V8360W Series Manual de usuario

Vicon

Vicon ROUGHNECK V910 Manual de usuario

Vicon

Vicon Surveyor MKII PTZ SV36W Manual de usuario

Vicon

Vicon Surveyor 2000-MSH Manual de usuario

Vicon

Vicon CE102B Manual de usuario

Vicon

Vicon SN663V-B Manual de usuario

Vicon

Vicon 240-60 Series Manual de usuario

Vicon

Vicon G-Cam/EFD-3266 Manual de usuario

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario