Vicon V682-PTZ Manual de usuario
User Guide
V682-PTZ
Outdoor Analog PTZ Dome Camera
XX307-20-00
Vicon Industries Inc. does not warrant that the functions contained in this equipment will
meet your requirements or that the operation will be entirely error free or perform precisely as
described in the documentation. This system has not been designed to be used in
life-critical situations and must not be used for this purpose.
Document Number: 8009-8307-20-00 Product specifications subject to change without notice.
Issued: 6/2021 Copyright © 2021 Vicon Industries Inc. All rights reserved.
Vicon Industries Inc.
Tel: 631-952-2288) Fax: 631-951-2288
Toll Free: 800-645-9116
24-Hour Technical Support: 800-34-VICON
(800-348-4266)
UK: 44/(0) 1489-566300
www.vicon-security.com
2
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO
NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE. DO
NOT INSERT ANY METALLIC OBJECTS THROUGH THE
VENTILATION GRILLS OR OTHER OPENINGS ON THE
EQUIPMENT.
CAUTION
EXPLANATION OF GRAPHICAL SYMBOLS
The lightning flash with arrowhead symbol, within an
equilateral triangle, is intended to alert the user to
the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle
is intended to alert the user to the presence of
important operating and maintenance (servicing)
instructions in the literature accompanying the
appliance.
3
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC INFORMATION: This equipment has been tested and found to
comply with the limits for a Class A digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in
a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference
to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003
du Canada.
CE COMPLIANCE STATEMENT
WARNING
This is a Class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
4
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the
third prong is provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plug’s,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally, or has been dropped.
15. CAUTION – THESE SERVICING INSTRUCTIONS ARE FOR USE BY
QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF
ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN
THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU
ARE QUALIFIED TO DO SO.
16. Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed
Class 2 power source only.
5
Contents
Chapter 1 — Introduction..................................................................................................6
1.1 Features .............................................................................................................................6
Chapter 2 — Installation and Configuration ....................................................................7
2.1 Package Contents..............................................................................................................7
2.2 Mounting the Camera ........................................................................................................ 8
2.2.1 Wall Mounting ............................................................................................................9
2.2.2 Ceiling Mounting .....................................................................................................10
2.3 Basic Configuration of Dome Camera System .............................................................. 11
2.4 Setting Dome Camera (DIP Switch) ................................................................................ 12
2.5 Setting Dome Camera Address (ID)................................................................................13
2.6 Connections.....................................................................................................................13
2.7 Getting Started.................................................................................................................14
Programming ...................................................................................................................15
3.1 Dome Camera Selection..................................................................................................15
3.2 Accessing the On-Screen Menu Utility........................................................................... 15
3.3 How to Control the On-Screen Menu Utility...................................................................15
3.4 Auto Scan.........................................................................................................................16
3.5 Preset ............................................................................................................................... 18
3.6 Tour................................................................................................................................... 20
3.7 Pattern ..............................................................................................................................21
3.8 Privacy Zone .................................................................................................................... 22
3.9 Camera Menu ...................................................................................................................23
3.10 Dome Communication...................................................................................................26
3.11 Alarm...............................................................................................................................26
3.12 Dome Setup.................................................................................................................... 27
Operation..........................................................................................................................33
Using a ViconNet VMS ..........................................................................................................33
Using a Valerus VMS..............................................................................................................34
Appendix A — Specifications .........................................................................................35
Appendix B – Programmed Presets...............................................................................37
Appendix C — Troubleshooting .....................................................................................38
6
Chapter 1 — Introduction
1.1 Features
• Built-in optical power zoom camera with True Night Shot function.
• 240 preset positions with the individual camera AE setup.
• 8 tours, consisting of presets, patterns, auto scans and other tours, can be programmed with
over 300 functions and preset locations. While moving, each preset scan can be watched in
smooth Vector Scan mode.
• 16 auto scans in the normal, the vector, and the random mode and the endless autopan with
13 speed steps.
• 8 patterns (up to 500 seconds) and 16 privacy zones.
• 4 alarm inputs, 2 alarm outputs (5VTTL).
• Variable speed from 0.1/sec. to 380/sec.
Three variable speeds (SLOW, NORMAL, TURBO).
• Pan/tilt speed is inversely proportional to the zoom ratio with the option.
• Maximum speed is 380/sec. when preset command.
• Auto calibration from 0.1 to 6 (tilt range is 0 to 180).
• Programmable user preferences (alarm, preset, title, etc.).
• 180 digital flip.
• Function Run menu using keyboard. without function key (preset, pattern, tour and scan).
• Built-in RS-485 receiver driver (up to 3999 selectable camera addresses).
• 12 VDC or 24 VAC for camera.
• 24 VAC for heater and fan.
7
Chapter 2 — Installation and Configuration
2.1 Package Contents
This system comes with the following components;
* Dome Camera 1
* Instruction Manual (this document) 1
* Accessory Kit & Connectors 1
1) Torx wrench (1)
2) 2-Pin Terminal Block (1)
3) 3-Pin Terminal Block (2)
4) 4-Pin Terminal Block (1)
5) 5-Pin Terminal Block (1)
* Install Adaptor 1
NOTE: Check your package to make sure that you received the complete system, including all
components listed above.
NOTE: Adapter for 12 VDC & 24 VAC is not supplied.
8
2.2 Mounting the Camera
An optional mount kit, either a wall mount or a ceiling mount, is required for installation.
The wall or ceiling mount must be attached to a structural object such as hard wood or concrete
that will support the weight of the mount and dome camera.
The use of a solid backboard is recommended when attaching to gypsum walls.
1. Remove the Protection pad and the tape from attached the dome camera.
2. Attach the mounting base to wall using the supplied M8 tapping screw and plastic bushing.
(For Ceiling installation use the supplied M6 tapping screw and bushing.)
3. To seal tightly, wrap the thread of the pipe end with Teflon tape about 20 times for sealing.
Then use a silicone rubber sealant to seal the area where the wall (ceiling) mount and the pipe
meet.
4. Place a bead of silicone sealant around the wall and ceiling mount mounting flange, press it to
the surface and line up the flange hole with drilled holes.
CAUTION 1: A silicone rubber sealant must be applied to seal the housing to secure
waterproofing.
CAUTION 2: When installing, a mounting bracket must be used.
CAUTION 3: Please reset the camera after 30 ~ 60 minutes when installing it in environments
colder than 14° F (-10°C).
CAUTION 4: Regardless of the installation environment, heater and fan power supply is
recommended.
9
2.2.1 Wall Mounting
The wall mounting plate must be attached to a structural object such as concrete that will support
the weight of the mount and dome camera.
1. Select a suitable mounting location and verify there is sufficient cable to reach the middle of
the wall mount.
2. Mark and drill mounting holes in the surface using the wall mount flange as a template.
3. Pull out cables required from the wall to connect to the dome camera.
4. Secure the wall mount bracket to the wall using plastic anchors and 8x35 screws provided or
hardware appropriate for the mounting surface.
5. Remove the access plate and pull cables out through rectangular access hole of the wall
mount bracket.
6. Attach the 1.5-inch adapter to wall mount bracket and secure it using set screw.
7. Attach the camera’s safety wire to the wall mount bracket and neatly gather cables.
8. Reattach the access plate of the wall mount bracket.
9. Push in and turn the camera clockwise into the adapter, and secure it using set screw of the
adapter.
10
2.2.2 Ceiling Mounting
The ceiling mounting plate must be attached to a structural object such as concrete that will
support the weight of the mount and dome camera.
This figure shows how to twist and lock the housing
with pipe.
1. Select a suitable mounting location
and verify there is sufficient cable to
connect with cables from the
housing.
2. Mark and drill mounting holes on the
surface using the ceiling mount
flange as a template.
3. Pull out the cables from the ceiling
required to connect to the dome
camera.
4. Attach the ceiling mount bracket
using plastic anchors and screws
appropriate for the mounting
surface.
5. Attach 1.5-inch adapter to the pipe
and secure it using set screw of the
adapter.
6. Route camera cables through the
pipe and attach the camera to
adapter and secure using set screw
of the adapter.
7. Attach safety wire to the pipe using
6x35 screws.
8. Connect cables and gather cables
neatly.
9. Lock hexagonal nut of the ceiling
mount bracket to secure camera’s
attached pipe and ceiling mount
bracket.
Tabla de contenidos
Otros manuales de Cámara de seguridad de Vicon
Vicon
Vicon V1020-WIR-180-1 Manual de usuario
Vicon
Vicon VC2650-DSP Manual de usuario
Vicon
Vicon SurveyorVFT SVFT-C266M Manual de usuario
Vicon
Vicon Roughneck V2100B Series Manual de usuario
Vicon
Vicon ROUGHNECK V910 Manual de usuario
Vicon
Vicon V960D-W Series Manual de instrucciones
Vicon
Vicon SVFT-PRS22E Manual de usuario
Vicon
Vicon V920B-A Series Manual de usuario
Vicon
Vicon VC2200-12 Guía del usuario
Vicon
Vicon XX152-10-01 Instrucciones de instalación
Vicon
Vicon Roughneck AI V2000D Series Manual de usuario
Vicon
Vicon SurveyorVFT SVFT-UPM-1 Manual de usuario
Vicon
Vicon VC-600W Manual de usuario
Vicon
Vicon I-ONYX MPD-980DN-O Manual de usuario
Vicon
Vicon S2000-MSH-HHB Surveyor 2000 Manual de usuario
Vicon
Vicon Roughneck V920D Series Manual
Vicon
Vicon Roughneck AI V2008B-W310LPR Manual de usuario
Vicon
Vicon V922B-W551MIR-A1 Manual de usuario
Vicon
Vicon roughneck V900 Manual de usuario
Vicon
Vicon VC5050-DSP Manual de usuario
