Vicon SN683D-WIR Manual de usuario

SN683D-WIR Outdoor PTZ Dome Camera

Quick Guide

Vicon Industries Inc. does not warrant that the functions contained in this equipment will

meet your requirements or that the operation will be entirely error free or perform precisely

as described in the documentation. This system has not been designed to be used in life-

critical situations and must not be used for this purpose.

Document Number: 8009-8270-50-00 Product specifications subject to change without

Vicon Industries Inc.

Tel: 631-952-2288) Fax: 631-951-2288

Toll Free: 800-645-9116

24-Hour Technical Support: 800-34-VICON

(800-348-4266) UK: 44/(0) 1489-566300

www.vicon-security.com

XX270-50-00

1 Introduction

The SN683D network camera is designed for performance in the most demanding security

installations. The 3 MP camera has an integral 36X optical zoom lens and integrated IR LEDs.

The camera provides quad-streaming video and supports H.265/H.264 compression technology,

drastically reducing file sizes and conserving valuable network bandwidth; M-JPEG compression is

also supported. By using its dedicated program, multiple users are able to have access to the

network camera simultaneously, or a single user can monitor various network cameras at the same

time. It also enable users to play, store and retrieve a monitoring image by using a PC. All the settings

and real time monitoring screens are provided through access to the web.

1.1 Components

This system comes with the following components;

* Dome Camera 1

* Quick Installation Guide 1

* 2P screw type Connector 1

* 5P screw type Connector 1

* PoE Injector 1

* RJ-45 Waterproof Cover 1

* Install Adaptor 1

NOTE: Check your package to make sure that you received the complete system, including all

components listed above.

NOTE: Adaptor for 12 VDC is not supplied.

1.2 Key Features

• Brilliant video quality

The network camera offers the highly efficient H.264/H.265 video compression, which drastically

reduces bandwidth and storage requirements without compromising image quality. Motion JPEG

is also supported for increased flexibility.

• Quad Streams

The network camera can deliver quad video streams simultaneously using H.264/H.265 and

Motion JPEG. This means that several video streams can be configured with different

compression formats, resolutions and frame rates for different needs.

• Intelligent video capabilities

The network camera includes intelligent capabilities such as enhanced video motion detection.

The network camera’s external inputs and outputs can be connected to devices such as sensors

and relays, enabling the system to react to alarms and activate lights or open/close doors.

• Improved Security

The network camera logs all user access, and lists currently connected users. Also, its full frame

rate video can be provided over HTTPS.

• ONVIF Certificate

This is a global interface standard that makes it easier for end users, integrators, consultants,

and manufacturers to take advantage of the possibilities offered by network video technology.

ONVIF enables interoperability between different vendor products, increased flexibility, reduced

cost, and future-proof systems.

• Micro-SD Recording support

The network camera also supports a Micro-SD memory slot for local recording with removable

storage of type SDHC and SDXC.

• Audio support

The network camera also supports two-way audio.

• Built-in Synchronized IR LED & Fixed IR LED

The camera is equipped with two built-in IR LEDs, fixed one for wide view and zoom

synchronized adjustable one for distant view.

2 Installation

2.1 Mounting the Camera

An optional mount kit, either a wall mount or a ceiling mount, is required for installation.

The wall or ceiling mount must be attached to a structural object such as hard wood or concrete that

will support the weight of the mount and dome camera.

The use of a solid backboard is recommended when attaching to gypsum walls.

1. Remove the Protection pad and the tape from the dome camera.

2. Attach the mounting base to wall using the supplied M8 tapping screw and plastic bushing. (For

ceiling mounting use the supplied M6 tapping screw and bushing.)

3. To seal tightly, wrap the thread of the pipe end with Teflon tape about 20 times for sealing. Then

use a silicone rubber sealant to seal the area where the wall (ceiling) mount and the pipe meet.

4. Place a bead of silicone sealant around the wall and ceiling mount mounting flange, press it to

the surface and line up the flange hole with drilled holes.

CAUTION 1: A silicone rubber sealant must be applied to seal the housing to secure

waterproofing.

CAUTION 2: When installing, a mounting bracket must be used.

CAUTION 3: Please reset the camera after 30 ~ 60 minutes when installing it in situations

colder than 14° F (-10°C).

2.1.1 Wall Mounting

The wall mounting plate must be attached to a structural object such as concrete that will support

the weight of the mount and dome camera.

1. Select a suitable mounting location and verify there is sufficient cable to reach the middle

of the Wall Mount.

2. Mark and drill mounting holes in the surface using the wall mount flange as a template.

3. Secure the mounting plate to the wall using the hardware provided or appropriate for the

mounting surface.

4. Pull out cables required to connect to the dome camera from the wall or route cables

through a section of 0.75 in (19 mm) conduit pipe.

5. Remove the cable access plate from the underside of the wall mount bracket.

6. Attach the wall mount bracket using plastic anchors and M8x35 screws; route cables

through the access plate hole.

7. Attach the 1.5 inch adapter to wall mount bracket and fix it using set screw.

8. Attach the camera’s safety wire to the wall mount’s latch.

9. Route cables on the dome through the wall mount bracket. Fix the housing to the wall mount

bracket using the locking nut and tighten the housing set screw with the supplied wrench.

10. Reattach the access plate.

11. Push in and turn the camera clockwise into the adapter and fix it using set screw of the

adapter.

2.1.2 Ceiling Mounting

The ceiling mounting plate must be attached to a structural object such as concrete that will support

the weight of the mount and dome camera.

This figure shows how to twist and lock the housing

with pipe.

1. Select a suitable mounting location

and verify there is sufficient cable to

connect with cables from the

housing.

2. Mark and drill mounting holes on the

surface using the ceiling mount

flange as a template.

3. Secure the mounting plate to the

wall using the hardware provided or

appropriate for the mounting

surface.

4. Pull out cables required to connect to

the dome camera from the ceiling.

5. Attach the ceiling mount plate using

plastic anchors and screws; route

cables through the locking nut.

6. Attach 1.5 inch adapter to the pipe

and fix it using set screw on the

adapter.

7. Route cables through the pipe.

Tighten the housing with the pipe

using the socket.

8. Attach the housing’s safety wire to

the ceiling mount’s M6x35 tapping

screw.

9. After connecting cables, fix the pipe

to the ceiling mount using the locking

nut.

10. Tighten set screws of the socket

and locking nut with the supplied

wrench.

2.2 Basic Configuration of Camera System

No.

Connector

Wire Color

Description

Power jack

BLACK

12 VDC CAMERA POWER

RJ-45

BLACK

Ethernet, RJ-45 port compatible with

10/100Mbps (Option PoE++ functionality)

RCA jack

BLACK

AUDIO INPUT

RCA jack

GRAY

AUDIO OUTPUT

5-pin cable

YELLOW

ALARM INPUT 1

WHITE

ALARM INPUT 2

VIOLET

ALARM INPUT 3

BROWN

ALARM INPUT 4

GRAY

GND

2-pin cable

RED

ALARM OUTPUT

BLACK

GND

The camera must be installed by qualified service personnel in accordance with all local and federal

electrical and building codes.

2.3 Resetting to the factory default settings

To reset the network camera to the original factory settings, go to the Setup > System > Maintenance

web page (described in “System > Maintenance” of User Manual) or use the Reset button on the

network camera, as described below:

• Using the Reset button:

Follow the instructions below to reset the network camera to the factory default settings using the

Reset button.

1. Switch off the network camera by disconnecting the power adapter.

2. Open the Micro-SD card cover.

3. Press and hold the Reset button on the board with your finger while reconnecting the power.

4. Keep the Reset button pressed for about 2 seconds.

5. Release the Reset button.

6. The network camera resets to factory defaults and restarts after completing the factory reset.

The unit now obtains the IP address automatically via DHCP.

7. Close the Micro-SD card cover tightly to ensure waterproofing.

CAUTION: When performing a Factory Reset, you will lose any settings that have been saved.

2.4 Connections

• Micro-SD Card Insertion

User can install and change Micro-SD card as shown in the following picture.

1. Open the Micro-SD card cover.

2. Install or change Micro-SD card.

3. Close the Micro-SD card cover tightly to ensure waterproofing.

• Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the camera. Generally a crossover cable

is used for directly connection to PC, while a direct cable is used for connection to a hub.

• Connecting Alarms

– A1, A2, A3, A4 (Alarm Input 1, 2, 3, 4)

You can use external devices to signal the camera to react on events. Mechanical or electrical

switches can be wired to the A1, A2, A3, A4 (Alarm Input 1, 2, 3, 4) and G (Ground)

connectors.

– G (Ground)

NOTE: All the connectors marked G or GND are common.

Connect the ground side of the alarm input and/or alarm output to the G (Ground) connector.

– AO (Alarm Output)

The camera can activate external devices such as buzzers or lights. Connect the device to

the AO (Alarm Output) and G (Ground) connectors.

• Connecting Audio

Connect speaker to audio output line and external mic to audio input line.

• Connecting the Power

Connect power of 12 VDC for the camera.

When using a 12 VDC adapter, connect the positive (+) pole to the ‘+’ position and the

negative (-) pole to the ‘-’ position.

Use satisfy clause 2.5 of IEC60950-1/UL60950-1 or Certified/Listed Class 2 power source only.

– Be careful not to reverse the polarity when you connect the power cable.

– You can also use a router featuring PoE (Power over Ethernet) to supply power to the

camera. If you use PoE to supply power to the camera, you must use the PoE (Power

over Ethernet) injector provided by the manufacturer for proper operation.

Tabla de contenidos

Otros manuales de Cámara de seguridad de Vicon

Vicon

Vicon Roughneck V2000D-PTZ Manual de usuario

Vicon

Vicon CE202D-WN Manual de usuario

Vicon

Vicon ROUGHNECK V910 Manual de usuario

Vicon

Vicon Surveyor MKII Series XX282-00-01 Manual de usuario

Vicon

Vicon V662-D Instrucciones de funcionamiento

Vicon

Vicon V7FCD Guía del usuario

Vicon

Vicon CE202D-N Manual de usuario

Vicon

Vicon surveyor 1000 Manual de usuario

Vicon

Vicon Series 247-00-03 Manual de usuario

Vicon

Vicon V940D Manual de usuario

Vicon

Vicon G-Cam/EFD-3266 Manual de usuario

Vicon

Vicon IX 4000 L Manual de usuario

Vicon

Vicon V922B-W551-A1 Manual de usuario

Vicon

Vicon I-Onyx VN-957DN Manual de usuario

Vicon

Vicon Series 234-00-02 Instrucciones de funcionamiento

Vicon

Vicon Roughneck V920D Series Manual de usuario

Vicon

Vicon XX264-20-00 Manual de usuario

Vicon

Vicon V661D-312IR Instrucciones de funcionamiento

Vicon

Vicon surveyor1000 Manual del propietario

Vicon

Vicon surveyor X971 Manual de usuario

Vicon

Vicon V2008-W0950-LPR Manual de usuario

Vicon

Vicon Cruiser SN663V Instrucciones de funcionamiento

Vicon

Vicon IX 8000 IR Manual de usuario

Vicon

Vicon Roughneck V920D Series Manual

Manuales populares de Cámara de seguridad de otras marcas

Okina USA

Okina USA SIR36-870VF650LP Manual de usuario

Divio

Divio NDR155PA Manual de usuario

Canon

Canon VB-C500D Manual de usuario

Easy Access

Easy Access EasyGuard Manual de usuario

Vivotek

Vivotek FD9389-EHV-v2 Manual de usuario

TUYA

TUYA COSMO W2 Manual de usuario

Eusso

Eusso UNC7500-IR Guía de configuración

urmet domus

urmet domus 1096/204 Manual de usuario

VC VC20 series Manual de usuario

Axis

Axis Q1614 Manual de usuario

ieGeek

ieGeek DD201 Manual de usuario

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manual de usuario

Grundig

Grundig GCH-K0274P Manual de usuario

Lorex

Lorex VANTAGE LBC7032 Manual de usuario

4xem

4xem WPT Manual de usuario

Samsung

Samsung SCV-3082 Manual de usuario

Vitek

Vitek VTC-C544 Manual de usuario

Lumens

Lumens VC-A50PNW Manual de usuario