Velleman High-Q K2572 Manual de usuario
K2572
ILLUSTRATED ASSEMBLY MANUAL H2572IP-1
Low noisepreamplifierto boost
smallsignals.
UNIVERSAL STEREO PRE - AMPLIFIER
2
Specifications:
Power supply: 10 - 30V DC maximum, stabilized.
Current absorption with out charge : typ. 5mA.
Adjustable gain : 40dB max.
Frequency range : 40Hz - 30KHz (-3dB).
Output impedance : 1KΩ.
Max. Input voltage : 50mVrms (500mVrms)
Dimensions : 44 x 65mm / 1,7” x 2,6”.
Features & Specifications
A1,A2 = IC1
A1
A2
R3
R4
R1
C6
5
8
IN-R
7
C1
R5
5
6
R2
C7
IN-L
3
4
6
R6
3
2
C4
+V
C7
RV1
C5
RV2
C3
+V
8
4
7
9
10
OUT-R
1
OUT-L
C2
1
2
3
Assembly hints
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.
1.1 Make sure you have the right tools:
A good quality soldering iron (25-40W) with a small tip.
Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and will
protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.
Thin raisin-core solder. Do not use any flux or grease.
A diagonal cutter to trim excess wires. To avoid injury when cutting excess leads, hold the lead so they
cannot fly towards the eyes.
Needle nose pliers, for bending leads, or to hold components in place.
Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or might be handy
1.2 Assembly Hints :
Make sure the skill level matches your experience, to avoid disappointments.
Follow the instructions carefully. Read and understand the entire step before you perform each operation.
Perform the assembly in the correct order as stated in this manual
Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
Values on the circuit diagram are subject to changes.
Values in this assembly guide are correct*
Use the check-boxes to mark your progress.
Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’ on a separate leaflet.
0
.0
0
0
4
Assembly hints
1.3 Soldering Hints :
1- Mount the component against the PCB surface and carefully solder the leads
2- Make sure the solder joints are cone-shaped and shiny
3- Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE ONE AT A TIME !
DO NOT BLINDLY FOLLOW THE ORDER OF THE
COMPONENTS ONTO THE TAPE. ALWAYS CHECK
THEIR VALUE ON THE PARTS LIST!
5
R1 : 22K (2 - 2 - 3 - B)
R2 : 22K (2 - 2 - 3 - B)
R3 : 1MΩ(1 - 0 - 5 - B)
R4 : 1MΩ(1 - 0 - 5 - B)
R5 : 10K (1 - 0 - 3 - B)
R6 : 10K (1 - 0 - 3 - B)
1. Resistors
R...
Construction
IC1 : 8p
2. IC socket. Watch the
position of the notch!
C4 : 100nF (104, u1)
3. Ceramic Capacitor
C...
C1 : 10µF
C2 : 1µF
C3 : 1µF
C5 : 1µF
C6 : 1µF
C7 : 1µF
C8 : 1µF
4. Electrolytic capacitors.
Watch the polarity !
C...
RV1 : 1K
RV2 : 1K
5. Potentiometers
IC1 : TL072
6 . IC. Watch the position of
the notch!
RV...
6
Use
Ten connections are provided on the pcb to connect the print with a device. These connections are identical
to those of the RIAA preamplifier K2573 and in case you use the connectors included in this kit, you may
interchange the two prints.
The grounds near the Ins and Outs are used to connect the shielded wires (-) of the connecting leads. The
output amplitude of the right and the left channel are totally independent settable by respectively RV1 &
RV2. As current consumption is very low, voltage can be taken from any well stabilized power supply of 10
trough 30V DC. Lower the gain from 100 to 10 if the input signal is bigger than 50mV (500mV max), by
replacing R5 & R6 by 100K resistors.
Remarks : A nonwell stabilized power supply will give a noise and hum. The leads, from and to the print,
must be as short as possible and make use of shielded wires only. Never place the preamp in the vicinity
of transformers or net.
7. Use
1. Ground
2. Out left
3. Ground
4. In left
5. Ground (Power supply)
6. + (power supply)
7. In right
8. Ground
9. Out right
10.Ground
7
PCB
8. PCB
Modifications and typographical errors reserved © Velleman nv.
H2572IP’1 - 2014 (rev 3.0)
5
4
1
0
3
2
9
3
1
0
1
2
7
VELLEMAN NV
Legen Heirweg 33, B-9890 GAVERE
Belgium (Europe)
Otros manuales para High-Q K2572
1
Tabla de contenidos
Otros manuales de Amplificador de Velleman
Velleman
Velleman K8060 Manual de usuario
Velleman
Velleman HQ-Power ANTM7 Manual de usuario
Velleman
Velleman K4040B Manual de usuario
Velleman
Velleman K8010 Manual de usuario
Velleman
Velleman K8040 Manual de usuario
Velleman
Velleman VM113 Manual de usuario
Velleman
Velleman HQ Power PA100U Manual de usuario
Velleman
Velleman VPA2100M Manual de usuario
Velleman
Velleman K8066 Manual de usuario
Velleman
Velleman VAS4A Manual de usuario
Velleman
Velleman HQ-Power VDSPROM7 Manual de usuario
Velleman
Velleman BTR4 Manual de usuario
Velleman
Velleman K1803 Manual de usuario
Velleman
Velleman K4040 Manual de usuario
Velleman
Velleman POWER BLOCK K8081 Manual de usuario
Velleman
Velleman HQ Power VPA2200MBN Manual de usuario
Velleman
Velleman K4001 Manual de usuario
Velleman
Velleman 8020 Manual de usuario
Velleman
Velleman VM100 Manual de usuario
Velleman
Velleman HQ Power PAA04 Manual de usuario
