Velleman K4003 Manual de usuario

Total solder points: 45

Skill level :

Beginner 1þ2o3o4o5oAdvanced

ILLUSTRATED MANUAL H4003P-ED1

2x30W STEREO AMPLIFIER K4003

Features:

þThe easy way to add quality stereo amplification to your project

þExcellent sound quality

þLow noise, low distortion

þShort circuit and overload protected (1h max.)

þOn-board rectifier and smoothing capacitor

þJust add a center tap transformer

þComplete with heatsink

Specifications :

þMax. output power : 2 x 15W/4 ohm -2 x 10W/8 ohm

þHarmonic distortion : 0.07% (1W/1kHz)

þChannel separation : 70dB

þFreq. response : 7Hz to 60kHz (-3dB)

þSignal/noise ratio : 98dB (A weight)

þInput sensitivity : 300mV / 20Kohm

þPower supply : 2 x 12V / 2A (50W centertap transformer)

þDimensions : 69 x 51mm / 2.7” x 2”

modifications reserved

4K7= ( 4 - 7 - 2 - B )

4K7= ( 4 - 7 - 0 - 1 - 1 )

COLOR= 2… 5

IPESF SDK NDGB FNL

CODICE

COLORE

CODIGO

CORES

CODIGO

DE COL-

ORES

VÄRI

KOODI FÄRG

SCHEMA

FARVE

KODE FARGE

KODE FARB

KODE

COLOUR

CODE CODIFI-

CATION

DES

COU-

LEURS

KLEUR

KODE

Nero Preto Negro Musta Svart Sort Sort Schwarz Black Noir Zwart 0

Marrone Castanho Marrón Ruskea Brun Brun Brun Braun Brown Brun Bruin 1

Rosso Encarnado Rojo Punainen Röd Rød Rød Rot Red Rouge Rood 2

Aranciato

Laranja Naranjado

Oranssi Orange Orange Orange Orange Orange

Orange

Oranje

Giallo Amarelo Amarillo Keltainen Gul Gul Gul Gelb Yellow Jaune Geel 4

Verde Verde Verde Vihreä Grön Grøn Grønn Grün Green Vert Groen 5

Blu Azul Azul Sininen Blå Blå Blå Blau Blue Blue Blauw 6

Viola Violeta Morado Purppura Lila Violet Violet Violet Purple Violet Paars 7

Grigio Cinzento Gris Harmaa Grå Grå Grå Grau Grey Gris Grijs 8

Bianco Branco Blanco Valkoinen Vit Hvid Hvidt Weiss White Blanc Wit 9

Argento Prateado Plata Hopea Silver Sølv Sølv Silber Silver Argent Zilver A

Oro Dourado Oro Kulta Guld Guld Guldl Gold Gold Or Goud B

__________________________________________________________________________________________________________________________________________________________

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful.

Read them carefully.

1.1 Make sure you have the right tools:

•A good quality soldering iron (25-40W) with a

small tip.

•Wipe it often on a wet sponge or cloth, to keep

it clean; then apply solder to the tip, to give it a

wet look. This is called ‘thinning’ and will protect the tip, and enables you to make good connections. When sol-

der rolls off the tip, it needs cleaning.

•Thin raisin-core solder. Do not use any flux or grease.

•A diagonal cutter to trim excess wires. To avoid injury

when cutting excess leads, hold the lead so they can-

not fly towards the eyes.

•Needle nose pliers, for bending leads, or to hold components in place.

•Small blade and phillips screwdrivers. A basic range is fine.

For some projects, a basic multi-meter is required, or might be

handy

1.2 Assembly Hints :

þMake sure the skill level matches your experience, to avoid disappointments.

þFollow the instructions carefully. Read and understand the entire step before you perform each operation.

þPerform the assembly in the correct order as stated in this manual

þPosition all parts on the PCB (Printed Circuit Board) as shown on the drawings.

þValues on the circuit diagram are subject to changes.

þValues in this assembly guide are correct*

þUse the check-boxes to mark your progress.

þPlease read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute manual updates, indicated as ‘NOTE’

on a separate leaflet.

1.3 Soldering Hints :

Mount the component against the

PCB surface and carefully solder the

leads

Make sure the solder joints are

cone-shaped and shiny Trim excess leads as close as pos-

sible to the solder joint

0.000

_______________________________________________________________________________________________________________________________________________________

1. RESISTORS R...

qR1 : 8.2 (8 -2 -B -B)

qR2 : 8.2 (8 -2 -B -B)

2. DIODES (Watch the polarity !)

CATHODE

D...

qD1 : 1N5400 … 5408

qD2 : 1N5400 … 5408

qD3 : 1N5400 … 5408

qD4 : 1N5400 … 5408

3. PCB PINS

q5xGND, 2xLS, 2xIN, VA, VB

4. CAPACITORS

C...

qC1 : 22nF (223)

qC2 : 22nF (223)

qC3 : 100nF (104, µ1)

qC4 : 1µF (105)

qC5 : 1µF (105)

5. ELECTROLYTIC CAPACITORS

(Watch the polarity!)

C...

qC6 : 4700µF

qC7 : 4700µF

6. IC (Watch the position !)

25mm

SILICON

GREASE

INSULATING MICA WASHER

qIC1 : TDA1521 or eq.

__________________________________________________________________________________________________________________________________________________________

7. CONNECTION EXAMPLE

12V

RIGHT

INPUT

FROM

AUDIO

SOURCE

LEFT

INPUT

FROM

AUDIO

SOURCE

8. HOW TO CONNECT A VOLUME CONTROL POTENTIOMETER

47K ohm log

FROM CD-PLAYER, TUNER, MIXER, ... TO K4003 AMPLIFIER IN

GND

_______________________________________________________________________________________________________________________________________________________

9. POWER SUPPLY OPTIONS

GND

12V

MAINS

TRANSFORMER : 2 x 12V 50VA

RED

YELLOW

BLUE

GRAY

10. PCB LAYOUT

__________________________________________________________________________________________________________________________________________________________

11. DIAGRAM

Otros manuales para K4003

Tabla de contenidos

Otros manuales de Amplificador de Velleman