Universal Tool UT8943 Manual de usuario

INSTRUCTION MANUAL - ENGLISH

Air Auto Shut-Off Pistol Screwdriver

This product is designed for installing and removing threaded fasteners in wood, metal and

plastic. The use of spare parts/ accessories other than those originally supplied by the

manufacturer may result in a drop in performance and/or increased maintenance / noise

level / vibrations. As a result, the full cancellation of the manufacturer’s liability. No other

use is permitted. Professional use only.

Air Supply Requirements

1. Supply tool with 6.35 KG/CM2(90 PSI) clean and dry air. Too much pressure drastically

reduces the tool life.

2. Connect the tool to air line using pipe, hose and fitting sizes shown in the diagram below.

Lubrication

1. Use an air line lubricator with SAE #10 oil. Adjustedto two (2) drops per minute. If an air

line lubricator is not available, add air motor oil to the inlet once a day.

2. For gearing and clutch, use Shell-grade grease containingmolybdenum.

3. Grease clutches every 12,000 screws.

Torque Adjustment

Shut Off Clutch: Grip the tool around the handle and press the tool into the fixing which is

to be tightened. The motor will start and tighten the fixing to the required torque set by

adjusting the tension on the clutch spring. At this point, the internal drive is disengaged and

the air to the motor cut off.

Operating Procedures

Air-inlet

Right/Left Switch

Torque Cover

Bit Retainer Sleeve

Trigger

1. Make sure the air in air line is clean and dry.

2. There are three air-inlets on the tool. Depending on different usage, choose one inlet to

connect correctly with the air compressor. Screw up the other two air-inlets separately

with screw caps.

3. Install a bit (as illustrated below). Before using, do check the bit being installed on the

tool correctly.

4. Torque Adjustment: Take off the torque cover and turn the torque adjustment ring right

(clockwise) to increase the torque. Turn the torque adjustment ring left

(counter-clockwise) to reduce the torque. After setting up the torque, put torque cover

back and fasten it tightly to avoid changing set-up accidently. (as illustrated below)

5. Right/Left Indication: Turn right (clockwise) the switch (marked “R”) for tightening screws.

Turn left (counter-clockwise) the switch (marked “L”) for loosening screws.

6. Two ways to operate:

A. Push + Pull The Trigger to Start: Set the bit aiming the screw. Push down the tool

steadily and pull the trigger to activate the motor. When the required torque is reached,

the motor will shut off automatically. Either releasing the trigger or take the tool away

from the fixing will stop the motor. (Dual security design)

B. Push to Start: Press the trigger and push the “Locking” switch to the right to lock the

trigger. Push down the tool steadily to activate the motor. The operation can be repeated

without pulling trigger constantly. When the required torque is reached, the motor will

shut off automatically.

7. Suggestion: Correct / Re-set torques before operation on a daily basis.

8. If the tool is not to be used for a long time, re-set the torque to the lowest.

Press & Lock

1234

Switch Operation of Three Way Air-inlet

Installation of Bit

Press the sleeve softly

Insert a bit

Make sure the bit

is fixed tightly

Shut off

123

Set-up of Torque

Operation of R/L Switch

12 3

678

12 3

678

1L 2L

Shut off 1R 2R

Turn clockwise to

increase the torque

Take off the

adjustment ring

Put the torque

cover back

Fasten the rear

housing tightly

Release and remove the torque cover

Insert torque

adjustment ring to

the tool

Turn counter clockwise

to lower the torque

R Indication –turn right (clockwise)

–fastening screw

L Indication –turn left (counter

clockwise) –loosening screw

1L 2L

1R 2R

1L 2L

1R 2R

UT8943 AUTO SHUT-OFF PISTOL SCREWDRIVER, 300rpm / 3.0~18Nm

INDEX NO.

PARTS NO. DESCRIPTION

QTY/SET

INDEX NO.

PARTS NO. DESCRIPTION

QTY/SET

17165001PG-1 TORQUE COVER 143 7165040PS ROTOR 1

27160070PG HOUSING CAP 144 7160042PS CYLINDER 1

37160002PS C RING 145 7160043PS END PLATE 1

47160003PS BIT RETAINER SLEEVE 146 SPP0208 SPRING PIN 1

57160004PS SPRING 147 B606ZZ-NMB BALL BEARING 1

67160005A TORQUE RING 148 7160048PG VALVE 1

77140007PS NEEDLE PIN 349 OR1898 O-RING 4

87165008PG CLUTCH HOUSING 150 7160063PG-BK MOTOR HOUSING 1

97160010A WASHER 151 7160052PS SCREW 1

10 7168011PG TORQUE SPRING 152 7160051PG-RD SWITCH 1

11 7160012PS ANVIL 153 HEXM806 SCREW 1

12 7160013PS STEEL BALL 154 7120067PG SCREW CAP 2

13 7160014PS STEEL BALL 255 HEXM308 SCREW 4

14 7160015PS SPRING 156 7120069PG VALVE BUSHING 1

15 7160016PS SLIDE BASE 157 589058 O-RING 2

16 7160017PS C RING 258 7165054PG OPERATING ROD 1

17 7160018PS BALL RACE 159 OR0302 O-RING 2

18 7160019PS STEEL BALL 60 60 7160056PS VALVE PLATE 1

19 7160020PS END CLUTCH 161 7160057PS SPRING 1

20 7160021PS-3P CENTER CLUTCH 162 7120068PG SCREW 1

21 STB3175 STEEL BALL 363 OR0612 O-RING 3

22 7160023PS-3P REAR CLUTCH 164 7120076PG PLUG 1

23 7160024PS RETAINER 165 611239-1 SPRING 1

24 7160025PS PILOT PIN 166 SB0003-1 STEEL BALL 1

25 B6001Z-TPI BALL BEARING 167 7120075PG TRIGGER LOCKING 1

26 7165027PG FRONT HOUSING 168 7120073PG SPRING 1

27 7165029PG SPACER 169 7120065PG TRIGGER PIN 1

28 7160030PS PIN 470 OR0312 O-RING 1

29 7165078PG PLANETARY GEAR 471 7120066PG BUSHING 1

30 7165036PG INTERNAL GEAR 172 7120074PG TRIGGER 1

31 7165077PG SUN GEAR 173 SPP0214 SPRING PIN 1

32 7150033PS GEAR CAGE 274 7120072PG GRIP 1

33 7150030PS PIN 475 OR2402 O-RING 1

34 7150031PS PLANETARY GEAR 476 ZZ389507 SILENCER 1

35 7150032PS SUN GEAR 177 7120071PG EXHAUST DEFLECTOR 1

36 7120030PS PIN 478 861432-3 SCREW 1

37 7120031PS PLANETARY GEAR 479 7120062PG AIR INLET 1

38 7165032PG SUN GEAR 180 7160080PS DISTINGUISHABLE RING(4) 1

39 L-1680HH BALL BEARING 181 CP1HP60 SUSPENSION RING 1

40 7165039PG FRONT PLATE 182 389847 ARM CASE 1

41 589040 SPRING PIN 283&84 389849/389848-1 WASHER & SCREW 1

42 7160041PS BLADE 485 389848 ARM 1

Division of Florida Pneumatic Mfg Corp.,

851 Jupiter Park Lane,

Jupiter, FL 33458, USA.

Ph: (1) 561 744 9500

Fax: (1) 561 575 5574

EC/UKCA DECLARATION OF CONFORMITY

We FLORIDAPNEUMATICMFGCORP,851JUPITERPARKLANE,JUPITER,FL33458,USA

Declareunderoursoleresponsibilitythatthemachinefallswithintheprovisionsofthe directive:

MachineType: UT8943 AirAutoShut-Off Screwdriver

TechnicalData:

ChuckSize: 1/4”HEXQC FreeSpeed: 300rpm

Weight: 1.45kg(3.19lbs) Length: 231mm(9.10”)

Recommended HoseSize: 10m(3/8”) WorkingAirPressure: 6.3bar(90PSI)

Noise: (soundpressurelevel) 72dB(A) Vibration: 1.81Metres/Sec ²

Spindlesize: N/A Serial No: ________________

Towhichthisdeclarationrelates,isinconformitywiththerequirementsof:TheMachineryDirective2006/42/EC,General

SafetyISO12100:2010,SpecificSafety-ImpactWrenches:ISO11148-6:2012,SpecificVibration- ISO28927,Noise:ISO

15744:2008

Nameandpositionofissuer: TonyLeNeveu:VPEngineering&Development

--------------------------------------------------------------------------------

Otros manuales de Destornillador eléctrico de Universal Tool

Universal Tool

Universal Tool UT8962-17 Manual de usuario

Universal Tool

Universal Tool UT8963AT-5 Manual de usuario

Universal Tool

Universal Tool UT8818-S Manual

Universal Tool

Universal Tool UT8933 Manual de usuario

Universal Tool

Universal Tool UT8934 Manual de usuario

Universal Tool

Universal Tool UT8226 Especificaciones

Universal Tool

Universal Tool UT2964 Manual de usuario

Universal Tool

Universal Tool UT2960A Manual de usuario

Universal Tool

Universal Tool UT8965 Manual de usuario

Universal Tool

Universal Tool AINA PTT Especificaciones

Universal Tool

Universal Tool UT8963AT-11 Manual de usuario

Universal Tool

Universal Tool UT8958 Especificaciones

Universal Tool

Universal Tool UT8955 Manual de usuario

Universal Tool

Universal Tool UT8962-11 Manual de usuario

Universal Tool

Universal Tool UT8963ATT-5 Manual

Universal Tool

Universal Tool UT8961-1 Manual de usuario

Universal Tool

Universal Tool UT8963AT-17 Manual de usuario

Universal Tool

Universal Tool UT8966 Manual de usuario

Universal Tool

Universal Tool UT8942 Manual de usuario

Universal Tool

Universal Tool UT8932 Manual de usuario

Universal Tool

Universal Tool UT8963-17 Manual de usuario

Universal Tool

Universal Tool UT8968 Manual de usuario

Universal Tool

Universal Tool UT8906 Especificaciones

Universal Tool

Universal Tool UT8961 Especificaciones

Manuales populares de Destornillador eléctrico de otras marcas

Makita

Makita DFT085F Manual de usuario

Parkside

Parkside 345138 2004 Manual de usuario

Makita

Makita DFL650F Manual de usuario

AEG

AEG BST 18BLX2-0 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand D5000 Series Manual de usuario

BGS technic

BGS technic 956 Manual de usuario

Hilti

Hilti SD 6000 Manual de usuario

Parkside

Parkside PEPS 3 A1 Manual de usuario

Festool

Festool TI 15 Manual de usuario

Makita

Makita DWT190 Manual de usuario

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Manual de usuario

Skil

Skil 2346 Instrucciones de montaje

DeWalt

DeWalt XR LI-ION DCD931 Manual de usuario

Festool

Festool DWC 18-2500 Manual de usuario

EINHELL

EINHELL TE-CD 12/1 Li Series Manual de usuario

Makita

Makita BFT043F Manual de usuario

Stanley

Stanley SCD2 Manual de usuario

Atlas Copco

Atlas Copco LUM12 SR Hoja de instrucciones