Universal Tool UT8934 Manual de usuario

INSTRUCTION MANUAL

Air Auto Shut-Off Straight Screwdrivers

This product is designed for installing and removing threadedfasteners in wood, metal,

and plastic. The use of spare parts/accessories other than those originally supplied by

the manufacturer may result in a drop in performance and/or increased

maintenance/noise level/vibrations, and as the result, the full cancellation of the

manufacturer’s liability. No other use is permitted. For professional use only.

Air Supply Requirements

1. Supply tool with 90 PSI (6.3 KG/CM2) of clean, dry air. Higher pressure drastically

reduces toollife.

2. Connect the tool to the airline using pipe, hose, and fitting sizes shown in the diagram

below.

Lubrication

1. Use an air line lubricator with SAE #10 oil, adjustedtotwo (2) drops per minute.

If an air line lubricator cannot be used, add air motor oil to the inlet once a day.

2. For gearing and clutch, use Shell-grade grease containingmolybdenum.

3. Grease clutches every 12,000 screws.

Torque Adjustment

Shut Off Clutch: Grip the tool around the handle and press the tool into the fixing

which is to be tightened. The motor will start and tighten the fixing to the required

torque set by adjusting the tensions on the clutch spring. At this point, the internal drive

is disengaged and the air to the motor cut off.

1/2" (12mm)

CA048362 (1/2") NPT

CA048361 (1/2") NPT

0 130

1/2" (12mm)

CA048360 (1/2") NPT

1/4 NPT

3/8" (10mm)

10' (3m) MAX

Torque Cover

Air Inlet

R/L Switch

Bit Retainer Sleeve

1234

Operating Procedures

1. Make sure the air in airline is clean and dry.

2. Make sure the tool is connected correctly with the air compressor.

3. Install a bit (as illustrated below). Before using, do check the bit being installed in the

tool correctly.

4. Torque Adjustment: Take off the torque cover and turn the torque adjustment ring

clockwise to increase the torque. Turn the torque adjustment ring counter-clockwise

to reduce the torque. When the torque is set up, put the torque cover back and

fasten it tightly to avoid changing the set-up accidentally. (as illustrated below)

5. Right/Left Indication: Turn right (clockwise) the switch (marked “R”) for tightening

screws. Turn left (counter-clockwise) the switch (marked “L”) for loosening screws.

6. Push to start: Push the tool to activate the motor.

7. Suggestion: Correct / Re-set torques before operation on a daily basis.

8. If not usedfor a long time, re-set the tool to the lowest torque.

Installation of Bit

Press the sleeve softly

Insert a bit

Make sure the bit

is fixed tightly

Set The Torque

R/L Switch

R Indication –turn right (clockwise) –fastening screw

L Indication –turn left (counter-clockwise) –loosening screw

12 3

678

12 3

678

Turn clockwise to

increase the torque

Take off the

adjustment ring

Put the torque

cover back

Fasten the rear

housing

Release the torque cover

Push Softly

Turn counter clockwise

to lower the torque

UT8934 AUTO SHUT-OFF STRAIGHT SCREWDRIVER - 550rpm / 1.5~10Nm

INDEX# PARTS NO.

PARTS DESCRIPTION QTY/SET INDEX# PARTS NO. PARTS DESCRIPTION

QTY/SE

17160001PS HOUSING CAP 141 7160041PS BLADE 5

27160061PS TORQUE COVER 142 7160040PS ROTOR 1

37160002PS C RING 143 7160042PS CYLINDER 1

47160003PS BIT RETAINER SLEEVE 144 SPP0208 SPRING PIN 1

57160004PS SPRING 145 7160045PS PIN 1

67160005PS TORQUE RING 146 7160043PS END PLATE 1

77160006PS REGULATION WASHER 147 7160046PS PIN 1

87160007PS NEEDLE PIN 348 B606ZZ BALL BEARING 1

97160008PS CLUTCH HOUSING 149 7160048PS VALVE 1

10 7160009PS ANVIL BUSHING 150 OR1898 O-RING 2

11 7160010PS WASHER 151 7160050PS END HOUSING 1

12 7160011PS TORQUE SPRING 152 7160063PS GRIP 1

13 7160013PS STEEL BALL 153 7160060PS SCREW HOLDER 1

14 7160012PS ANVIL 154 7160052PS SCREW 1

15 7160014PS STEEL BALL 255 7160051PS SWITCH 1

16 7160015PS SPRING 155 7160051PS-RD SWITCH 1

17 7160016PS SLIDE BASE 156 OR283178 O-RING 1

18 7160017PS C RING 257 7160054PS OPERATING ROD 1

19 7160018PS BALL RACE 158 OR0302 O-RING 1

20 7160019PS STEEL BALL 60 59 7160056PS VALVE PLATE 1

21 7160020PS END CLUTCH 160 7160057PS SPRING 1

22 7160021PS CENTER CLUTCH 161 7160058PS SILENCER 2

23 STB3175 STEEL BALL 262 7160059PS EXHAUST DEFLECTOR 1

24 7160023PS REAR CLUTCH 163 ZZ389507 SILENCER 1

25 7160024PS RETAINER 164 7160062PS AIR INLET 1

26 7160025PS PILOT PIN 165 CP1HP60 SUSPENSION RING 1

27 B6001Z-TPI BALL BEARING 1

28 7160027PS CENTER HOUSING 1

29 7160028PS WASHER 1

30 7160029PS GEAR CAGE 1

31 7160030PS PIN 4

32 7160031PS PLANT GEAR 4

33 7160032PS SUN GEAR 1

34 7160033PS GEAR CAGE 1

35 7160034PS PIN 4

36 7160035PS PLANT GEAR 4

37 7160036PS INTERNAL GEAR 1

38 RTW-16 C RING 1

39 L-1680HH BALL BEARING 1

40 7160039PS FRONT PLATE 1

7160080PS

DISTINGUISHABLE

RING(4)

7160064PS

TORQUE ADJUSTMENT

RING

Division of Florida Pneumatic Mfg Corp.,

851 Jupiter Park Lane,

Jupiter, FL 33458, USA.

Ph: (1) 561 744 9500

Fax: (1) 561 575 5574

EC/UKCA DECLARATION OF CONFORMITY

We FLORIDAPNEUMATICMFGCORP,851JUPITERPARKLANE,JUPITER,FL33458,USA

Declareunderoursoleresponsibilitythatthemachinefallswithintheprovisionsofthe directive:

MachineType: UT8934 AirAutoShut-OffScrewdriver

TechnicalData:

ChuckSize: 1/4”HEXQC FreeSpeed: 550rpm

Weight: 0.84 kg(1.85lbs) Length: 227 mm(8.9”)

Recommended HoseSize: 10m(3/8”) WorkingAirPressure: 6.3bar(90PSI)

Noise: (soundpressurelevel) 72dB(A) Vibration: 1.81Metres/Sec ²

Spindlesize: N/A Serial No: ________________

Towhichthisdeclarationrelates,isinconformitywiththerequirementsof:TheMachineryDirective2006/42/EC,

GeneralSafetyISO12100:2010,SpecificSafety-ImpactWrenches:ISO11148-6:2012,SpecificVibration- ISO

28927,Noise:ISO15744:2008

Nameandpositionofissuer: TonyLeNeveu:VPEngineering&Development

--------------------------------------------------------------------------------

Tabla de contenidos

Otros manuales de Destornillador eléctrico de Universal Tool

Universal Tool

Universal Tool UT8963ATT-11 Manual

Universal Tool

Universal Tool UT8957 Especificaciones

Universal Tool

Universal Tool UT8958 Especificaciones

Universal Tool

Universal Tool UT8962-17 Manual de usuario

Universal Tool

Universal Tool UT8963 Manual de usuario

Universal Tool

Universal Tool UT8966 Manual de usuario

Universal Tool

Universal Tool UT8818-S Manual

Universal Tool

Universal Tool UT8931 Manual de usuario

Universal Tool

Universal Tool UT8955 Especificaciones

Universal Tool

Universal Tool UT8963AT-11 Manual de usuario

Universal Tool

Universal Tool UT8961-1 Manual de usuario

Universal Tool

Universal Tool UT8963AT-17 Manual de usuario

Universal Tool

Universal Tool UT8960-2 Manual

Universal Tool

Universal Tool UT2960A Manual

Universal Tool

Universal Tool UT8906 Especificaciones

Universal Tool

Universal Tool UT8968 Manual de usuario

Universal Tool

Universal Tool UT8963-17 Manual de usuario

Universal Tool

Universal Tool UT8963ATT-5 Manual

Universal Tool

Universal Tool UT8955 Manual de usuario

Universal Tool

Universal Tool UT2960A Manual de usuario

Universal Tool

Universal Tool UT8943 Manual de usuario

Universal Tool

Universal Tool UT8965 Manual de usuario

Universal Tool

Universal Tool AINA PTT Especificaciones

Universal Tool

Universal Tool UT8961 Especificaciones

Manuales populares de Destornillador eléctrico de otras marcas

Makita

Makita DFT085F Manual de usuario

Parkside

Parkside 345138 2004 Manual de usuario

Makita

Makita DFL650F Manual de usuario

AEG

AEG BST 18BLX2-0 Manual de usuario

Ingersoll-Rand

Ingersoll-Rand D5000 Series Manual de usuario

BGS technic

BGS technic 956 Manual de usuario

Hilti

Hilti SD 6000 Manual de usuario

Parkside

Parkside PEPS 3 A1 Manual de usuario

Festool

Festool TI 15 Manual de usuario

Makita

Makita DWT190 Manual de usuario

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Manual de usuario

Skil

Skil 2346 Instrucciones de montaje

DeWalt

DeWalt XR LI-ION DCD931 Manual de usuario

Festool

Festool DWC 18-2500 Manual de usuario

EINHELL

EINHELL TE-CD 12/1 Li Series Manual de usuario

Makita

Makita BFT043F Manual de usuario

Stanley

Stanley SCD2 Manual de usuario

Atlas Copco

Atlas Copco LUM12 SR Hoja de instrucciones