Uniden AppCam Solo 2 Manual de usuario
AppCam Solo 2
Quick Start Guide
What’s in the Box
2
AppCam Solo 2
Camera
x1
Rechargeable
Battery
x1
Screw Mount
x1
Mounting
Strap
x1
Reset
Needle
x1
Screw
Kit
x2
Mounting
Template
x2
Power
Cable
x1
Weatherproof
Silicone Cover
x1
Magnetic Mount
x1
Red LED (Wi-Fi connection failed)
Blinking: Standby status
On: Working status
Blue LED (Wi-Fi connection succeeded)
Blinking: Standby status
On: Working status
General Introduction
Micro SD Card Slot
Reset Button
Daylight Sensor
Lens
Status LED
Built-in Mic
Speaker
Magnetic Mount
Built-in PIR Motion Sensor
3
Install the Rechargeable Battery to
the Camera
Step 1
Please press the button (on the top of the back casing), and slide the back casing downward
to close it. The button also needs to be closed firmly for good weatherproof performance.
For the weatherproof performance, always cover the USB charging port with the
rubber plug.
4
Charge the Battery
5
AppCam
Solo 2
Power Cable Rechargeable
Battery
AppCam Solo 2
Solar Panel
(Not included in
the package)
1. You can charge the battery when it’s installed to the camera.
2. You can charge the battery separately.
3. You can charge the battery with Uniden AppCam Solo 2 Solar Panel. Please note that
the solar panel is NOT included in the package.
There is a status LED under the micro USB port of the battery, indicating the battery charging status.
•Green LED: Fully charged
•Orange LED: Charging
1. Charge the battery when it’s installed
to the camera.
2. Charge the battery separately.
6
3. You can charge the battery with Uniden AppCam Solo 2 Solar Panel. Please note that
the solar panel is NOT included in the package.
7
1. Please charge your rechargeable battery with a standard and high-quality DC 5V
or 9V battery charger.
2. If you want to power the camera via the solar panel, please note that the camera
is ONLY compatible with Uniden Solar Panel. You cannot charge this camera with
other solar panel brands.
3. Please charge the battery in temperatures between 0°C and 45°C.
Please read the battery warnings and safety document provided in this
guide to use your Uniden Solo 2 rechargeable battery safely.
Uniden AppCam Solo 2 is not designed for 24/7 full capacity running or around-the-
clock live streaming. It’s designed to record motion events and remotely view live
streaming only when you need it.
Please learn some useful ways to maximize the battery life in this post:
https://kb.uniden.com/customer/portal/articles/2949997-appcam-solo-battery-savings
Important Safeguards on Rechargeable
Battery Use
!
8
9
1. Please charge the rechargeable battery with a standard and high-quality DC 5V or 9V
battery charger.
2. If you want to power the battery via the solar panel, please note that the battery is ONLY
compatible with Uniden Solo 2 Solar Panel. You cannot charge the battery with other solar
panel brands.
3. Please charge the battery in temperatures between 32°F and 113°F (0°C and 45°C).
4. Always use the battery in temperatures between -4°F and 140°F (-20°C and 60°C).
5. Please make sure the battery compartment is clean.
6. Please keep the USB charging port dry, clean and free of any debris and make sure the battery
contacts are aligned.
7. Always make sure the USB charging port is clean. Please cover the USB charging port with the
rubber plug after the battery has been fully charged.
8. Never charge, use or store the battery near any ignition sources, such as fire or heaters.
9. Always store the battery in a cool, dry and ventilated environment.
10. Never store the battery with any hazardous or combustible objects.
11. Do keep the battery away from children.
12. Do not short-circuit the battery by connecting wires or other metal objects to the positive (+)
and negative (-) terminals. Do NOT transport or store the battery with necklaces, hairpins or
other metal objects.
13. Do NOT disassemble, cut, puncture, short-circuit the battery, or make it dispose of in water, fire,
microwave ovens and pressure vessels.
14. Do NOT use the battery if it gives o an odor, generates heat, becomes discolored or
deformed, or appears abnormal in any ways. If the battery is being used or charged, remove
the battery from the device or the charger immediately, and stop using it.
15. Always follow the local waste and recycle laws when throwing the used battery away.
Install AppCam Solo App
Set up the Camera
There are two ways to get the AppCam
Solo App:
• Search “AppCam Solo” in App Store (for iOS)
download and install the app.
• Search “AppCam Solo” in Google Play
(for Android), download and install the app.
Please follow the prompt tone to
configure the camera
Please run App. Click the “Add New
Device” button, and follow the instructions
to set up the camera.
1. Please click the “ ’’ button in the
top right corner to add the camera.
10
Otros manuales para AppCam Solo 2
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Uniden
Uniden
Uniden UDR744 Manual de usuario
Uniden
Uniden UDW10055 Guía del usuario
Uniden
Uniden GNC 701 Manual de usuario
Uniden
Uniden Guardian G710PTZC Manual de usuario
Uniden
Uniden UWS1100 Manual de usuario
Uniden
Uniden SOLO+ Manual de usuario
Uniden
Uniden App Cam Spotlight+ Manual de usuario
Uniden
Uniden UDWC25 Manual de usuario
Uniden
Uniden UDRC57HD Manual de usuario
Uniden
Uniden App Cam Solo Pro Series Manual de usuario
Uniden
Uniden App Cam Home+ Manual de usuario
Uniden
Uniden G101 Manual de usuario
Uniden
Uniden AppCam 25HD Manual de usuario
Uniden
Uniden APPCAM23 Manual de servicio
Uniden
Uniden App Cam Solo 4G PT Manual de usuario
Uniden
Uniden BW31PTZ Manual de usuario
Uniden
Uniden APPCAM23A Manual de usuario
Uniden
Uniden Guardian GC45 Manual de servicio
Uniden
Uniden Guardian GC45 Manual de usuario
Uniden
Uniden App Cam Home Manual de usuario
