Uniden LightCam 40HD Manual de usuario
LightCam 40HD
Installation Guide
© 2018 Uniden America Corporation
Irving, Texas
Issue 1, July 2018
Printed in China
CUSTOMER CARE
At Uniden®, we care about you!
If you need assistance, please do NOT return this product
to your place of purchase.
Save your receipt/proof of purchase for warranty.
Quickly find answers to your questions by:
1. Reading your owner’s manual.
2. Visiting our customer support website at www.
uniden.com.
Images in this manual may differ slightly from your
actual product.
Uniden surveillance products are not manufactured and/
or sold with the intent to be used for illegal purposes.
Uniden expects consumer’s use of these products to
be in compliance with all local, state and federal law.
For further information on video surveillance and audio
recording legal requirements, please consult your local,
state and federal law.
© 2018 Uniden America Corporation
All rights allowed by law are hereby reserved.Information
in this document is subject to change without notice.
CONTENTS
CUSTOMER CARE ..................................2
OVERVIEW .............................................5
REQUIREMENTS ....................................5
WHAT’S IN THE BOX ..............................5
PARTS OF THE LIGHTCAM 40HD .........6
INSTALL THE CAMERA..........................6
CONSIDERATIONS.........................................................6
PROCEDURES..................................................................6
FCC/INDUSTRY CANADA
INFORMATION....................................9
FCC PART 15/IC COMPLIANCE .............9
- 5-
UNIDEN
LIGHTCAM 40HD
INSTALLATION MANUAL
OVERVIEW
Thanks for choosing Uniden LightCam 40 HD spotlight camera. This
Installation Guide provides basic hardware installation and setup
information so you can quickly get your system installed and for
further setup. Download the Quick Start Guide from www.uniden.
com for details.
REQUIREMENTS
xThe light control requires 120-volts AC.
xThis product is intended for use with the enclosed gasket
and with a junction box marked for use in wet locations (not
included).
xPhillips-head screwdriver.
WHAT’S IN THE BOX
LightCam 40HD Mounting Screws
(2)
Wire Connectors
(2)
Gasket
- 6-
PARTS OF THE LIGHTCAM 40HD
Antenna
Status
Indicator
LED
Ambient Light
Sensor
IR
Light
Lens
Screw
Locations
Adjustment
Screw
Adjustment
Collar
Motion Sensor
LEDs (6)
INSTALL THE CAMERA
Install the LightCam 40HD in a verticle (from the ceiling or eaves)
or horizontal (against a wall) position. Installation instructions are
identical for either position.
CONSIDERATIONS
xIf there is no junction box for wiring in the location where you
want to install this camera, you must add a junction box.
xDo not install the camera where the sun will shine directly into
the lens.
PROCEDURES
1. Turn off power to the junction box where the camera will be
located.
- 7-
WARNING: TURN POWER OFF AT THE CIRCUIT BREAKER OR
FUSE BOX. DO NOT ASSUME TURNING POWER OFF AT A
WALL SWITCH WILL TURN OFF ALL POWER TO THE AREA
YOU NEED.
2. Pull wires from mounting location (ceiling/eaves, wall, etc).
3. Pull the camera wires through the gasket; press gasket flush
to mounting base.
4. Strip 3/4-inch of the wire coating from the camera wires.
Twist each camera wire with its corresponding house wire
twice (white to white, black to black). Top each connection
with wire caps.
If there is a ground wire, tuck it into junction box.
5. Tuck wiring into the junction box.
6. Align the mounting base screw holes with the screw holes in
the junction box. Verify that the gasket is evenly positioned
around the base. Using a Phillips’ head screwdriver, screw the
camera base to the junction base with the screws provided.
Do not over-tighten.
- 8-
7. Position the camera roughly where you want it. Tighten the
adjustment collar.
8. Loosen the small adjustment screw on the side of the stand.
Fine-tune the camera position and then tighten the screw.
Again, do not over-tighten.
Adjustment
Screw
9. Caulk edge of mounting base with silicone weather-resistant
sealant (not included).
10. Turn power back on.
- 9-
One-Year Limited Warranty
Important: Evidence of original purchase is required for warranty
service.
WARRANTOR: Uniden America Corporaon (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the
original retail owner, this Uniden Product to be free from defects
in materials & crasmanship with only the limitaons or exclu-
sions set out below.
WARRANTY DURATION: This warranty to the original user shall
terminate & be of no further eect 12 months aer the date
of original retail sale. The warranty is invalid if the Product is
(A) damaged or not maintained as reasonable or necessary, (B)
modied, altered, or used as part of any conversion kits, subas-
semblies, or any conguraons not sold by Uniden, (C) improp-
erly installed, (D) serviced or repaired by someone other than an
authorized Uniden service center for a defect or malfuncon
covered by this warranty, (E) used in any conjuncon with equip-
ment or parts or as part of any system not manufactured by
Uniden, or (F) installed or programmed by anyone other than as
detailed by the owner’s manual for this product.
STATEMENT OF REMEDY: In the event that the product does not
conform to this warranty at any me while this warranty is in ef-
fect, warrantor will either, at its opon, repair or replace the de-
fecve unit & return it to you without charge for parts, service,
or any other cost (except shipping & handling) incurred by war-
rantor or its representaves in connecon with the performance
of this warranty. Warrantor, at its opon, may replace the
unit with a new or refurbished unit.
THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE & EN-
TIRE WARRANTY PERTAINING TO THE PRODUCT & IS IN LIEU OF
& EXCLUDES ALL OTHER WARRANTIES OF ANY NATURE WHAT-
SOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERA-
TION OF LAW, INCLUDING, BUT NOT LIMITED TO ANY IMPLIED
- 10 -
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTIC-
ULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PRO-
VIDE FOR THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL
OR CONSEQUENTIAL DAMAGES. Some states do not allow this
exclusion or limitaon of incidental or consequenal damages so
the above limitaon or exclusion may not apply to you.
LEGAL REMEDIES: This warranty gives you specic legal rights, &
you may also have other rights which vary from state to state.
This warranty is void outside the United States of America &
Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If,
aer following the instrucons in the owner’s manual you are
certain that the Product is defecve, pack the Product carefully
(preferably in its original packaging). Disconnect the baery
from the Product & separately secure the baery in its own sep-
arate packaging within the shipping carton. The Product should
include all parts & accessories originaly packaged with the Prod-
uct. Include evidence of original purchase & a note describing
the defect that has caused you to return it. The Product should
be shipped freight prepaid, by traceable means, to warrantor at:
Uniden America Service
C/O Saddle Creek
743 Henriea Creek Rd. , Suite 100
Roanoke, TX 76262
Otros manuales para LightCam 40HD
1
Tabla de contenidos
Otros manuales de Cámara de seguridad de Uniden
Uniden
Uniden Guardian G710PTZC Manual de usuario
Uniden
Uniden UDS655 Manual de usuario
Uniden
Uniden App Cam Solo 4G PT Manual de usuario
Uniden
Uniden App Cam Home+ Manual de usuario
Uniden
Uniden APPCAM23 Manual de servicio
Uniden
Uniden UDS655 Manual de usuario
Uniden
Uniden UDR444 Manual de usuario
Uniden
Uniden UWS1100 Manual de usuario
Uniden
Uniden App Cam Solo+ Manual de usuario
Uniden
Uniden App Cam Home Manual de usuario
Uniden
Uniden App Cam Pano Series Manual de usuario
Uniden
Uniden UDRC58HD Manual de usuario
Uniden
Uniden 4KTPD-MVF Manual de usuario
Uniden
Uniden UDR744 Manual de usuario
Uniden
Uniden APPCAM PAN/TILT Manual de usuario
Uniden
Uniden AppCam 50HD Manual de usuario
Uniden
Uniden ULC58 Manual de usuario
Uniden
Uniden App Cam Solo PT Manual de usuario
Uniden
Uniden UDR444 Manual de usuario
Uniden
Uniden AppCam Solo 2 Manual de usuario
