Ubiquiti Airmax NBE-M2-400 Manual de usuario

High-Performance

Integrated InnerFeed™

airMAX®Bridge

Models:

NBE-M2-400, NBE-M5-400

Introduction

Thank you for purchasing the Ubiquiti Networks™NanoBeam™.

This Quick Start Guide is designed to guide you through

the installation, and show you how to access the airOS®

Configuration Interface. This Quick Start Guide also includes the

warranty terms and is for use with the NanoBeamM2, model

NBE-M2-400, and the NanoBeamM5, model NBE-M5-400.

If you want to add a radome to enclose the Dish Reflector,

UbiquitiNetworks offers the NanoBeam Radome, 400 mm,

modelNBE-RAD-400 as an optional accessory. Product details are

available on our website at www.ubnt.com/airmax

Package Contents

Dish Reflector NBE-M2-400

Antenna Feed

NBE-M5-400

Antenna Feed*

Rear Housing Dish Bracket Pole Clamp U-Bolt

High-Performance

airMAX®Bridge

Models:

NBE-M2-400, NBE-M5-400

Flange Nuts

(M8, Qty. 2)

PoE Adapter

(24V, 0.5A)

Power Cord Quick Start Guide

* The NBE-M5-400 Antenna Feed has a thin gray ring around the center of

the cap to differentiate it from the NBE-M5-300 Antenna Feed.

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™

is designed for outdoor installations. It is the customer’s responsibility to follow local country

regulations, including operation within legal frequency channels, output power, and Dynamic

Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Technology

Ethernet Port

Release

Button Slot

Dish Bracket

Release Button

Dish

Reflector

Alignment Pins

Reset Button

Antenna Feed

Antenna Feed The NanoBeamM2 Antenna Feed is shown;

however, the NanoBeamM5 Antenna Feed has the same layout

for the Ethernet Port, Reset button, and Release button.

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the NanoBeam is

already poweredon.

Release Button After you assemble the NanoBeam, check the

Release button; it should be fully engaged in the Release Button

Slot of the Rear Housing. This ensures that the Antenna Feed is

locked into place. If you need to remove the Antenna Feed, you

must depress the Release button first.

LEDs

Signal In airOS, you can modify the wireless signal

strength threshold values for each LED on the

Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light green when the wireless signal

strength is above -65 dBm.

LED will light green when the wireless signal

strength is above -73 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light red when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light green when the

device is connected to a power source.

Application Examples

The NanoBeam mounted outdoors with the Dish Reflector

installed provides directional outdoor coverage (gain is

reflector-dependent).

The NanoBeam mounted outdoors without the Dish Reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 13 mm or ½" wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from the

most brutal environments and devastating ESD attacks

with industrial-grade shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

Installation

The installation instructions show the NanoBeamM2; however,

the same instructions apply to the NanoBeamM5.

1. Align and insert the tabs of the Dish Bracket into the

slots of the Dish Reflector. Rotate the Dish Bracket

counter-clockwise until the tabs lock into place.

2. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Dish Bracket. Insert the pins and

push until they lock intoplace.

*720-00004-01*

720-00004-01

3. Push in the sides of the Cable Door and detach it from the

Rear Housing.

4. Attach the Antenna Feed:

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release button is fully engaged.

Release Button

Bottom View

5. Connect the Ethernet cable:

a. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed.

b. Re-attach the Cable Door to the Rear Housing.

6. Slide the Pole Clamp onto the Dish Bracket.

7. Insert the U-Bolt into the Pole Clamp and Dish Bracket.Secure

each end of the U-Bolt with a Flange Nut.

25 N-m

(18 lb-ft)

Note: The mounting assembly can accommodate a

Ø 1.25" - 2.2" pole.

8. Optional: If you have the NanoBeam Radome (optional

accessory), then align the arrows on the bottoms of the

Radome and Dish Reflector so the Drain Holes on the Radome

point downward. Snap the Radome onto the Dish Reflector.

9. Connect the other end of the Ethernet cable from the

NanoBeam to the Ethernet port labeled POE on the

PoEAdapter.

10. Connect an Ethernet cable from your LAN or computer to

the Ethernet port labeled LAN on the PoE Adapter.

11. Connect the Power Cord to the power port on the PoE

Adapter. Connect the other end of the Power Cord to a

power outlet.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Ubiquiti

Ubiquiti

Ubiquiti UniFi Cloud Key Gen2 Plus Manual de usuario

Ubiquiti

Ubiquiti PowerBeam airMAX AC Gen2 PBE-5AC-Gen2 Manual de usuario

Ubiquiti

Ubiquiti airVision-C Manual de usuario

Ubiquiti

Ubiquiti ER-4 Manual de usuario

Ubiquiti

Ubiquiti UniFi US-48-500W Manual de usuario

Ubiquiti

Ubiquiti NanoBeam M Manual de usuario

Ubiquiti

Ubiquiti UniFi Cloud Key Manual de usuario

Ubiquiti

Ubiquiti U-Installer Manual de usuario

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Manual de usuario

Ubiquiti

Ubiquiti UF-Instant Manual de usuario

Ubiquiti

Ubiquiti R5AC-PTP Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-Gen2 Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-2AC-400-US Manual de usuario

Ubiquiti

Ubiquiti airMAX NanoStationM2 Manual de usuario

Ubiquiti

Ubiquiti UniFi WiFi BaseStation XG Manual de usuario

Ubiquiti

Ubiquiti EdgeSwtch 5XP Manual de usuario

Ubiquiti

Ubiquiti UF-AE Manual de usuario

Ubiquiti

Ubiquiti UAP-AC-PRO Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-400-ISO Manual de usuario

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Manual de usuario

Ubiquiti

Ubiquiti mFi mPort Manual de usuario

Ubiquiti

Ubiquiti NanoBeam M5 Manual

Ubiquiti

Ubiquiti UBI-POWERBEAM-M5-300 Manual de usuario

Ubiquiti

Ubiquiti M900 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario