Ubiquiti UBI-POWERBEAM-M5-300 Manual de usuario

High-Performance

Integrated InnerFeed®

airMAX®Bridge

Model: PBE-M5-300

Introduction

Thank you for purchasing the Ubiquiti Networks®

PowerBeam®.This Quick Start Guide is designed to guide you

through installation and also includes warranty terms.

Package Contents

Dish Reflector Antenna Feed Rear Housing Dish Bracket

Pole Clamp U-Bolt Flange Nuts

(Qty. 2)

Washers

(Qty. 2)

High-Performance

IntegratedInnerFeed®

airMAX®Bridge

Model:PBE-M5-300

PoE Adapter (24V, 0.5A)

with Mounting Bracket

Power Cord Quick Start Guide

cable and earth grounding must be used as conditions of product warranty. TOUGHCable™is

designed for outdoor installations. It is the professional installer’s responsibility to follow local

country regulations, including operation within legal frequency channels, output power, and

Dynamic Frequency Selection (DFS) requirements.

Hardware Overview

Bottom View

Cable Door

Rear Housing

Antenna Feed

Ethernet Port

Release

Button Slot

Dish Bracket

Release Button

Dish

Reflector

Alignment Pins

Reset Button

Technology

Reset Button To reset to factory defaults, press and hold the

Reset button for more than 10 seconds while the PowerBeam

is poweredon. Alternatively, the PowerBeam may be reset

remotely via a Reset button located on the bottom of the

PoEAdapter.

Release Button After you assemble the PowerBeam, check

the Release button; it should be fully engaged in the Release

Button Slot of the Rear Housing. This ensures that the Antenna

Feed is locked into place. If you need to remove the Antenna

Feed, you must depress the Release button first.

LEDs

Signal In airOS®, you can modify the wireless

signal strength threshold values for each LED on

the Advanced tab under Signal LED Thresholds. The

default values are shown below:

LED will light green when the wireless signal

strength is above -65 dBm.

LED will light green when the wireless signal

strength is above -73 dBm.

LED will light amber when the wireless signal

strength is above -80 dBm.

LED will light red when the wireless signal

strength is above -94 dBm.

Ethernet The Ethernet LED will light steady green

when an active Ethernet connection is made and

flash when there is activity.

Power The Power LED will light green when the

device is connected to a power source.

Application Examples

The PowerBeam mounted outdoors with the Dish Reflector

installed provides directional outdoor coverage (gain is

reflector-dependent).

The PowerBeam mounted outdoors without the Dish Reflector

installed provides outdoor-to-indoor coverage using the 3 dBi

Antenna Feed only.

Installation Requirements

• 10 mm wrench

• Shielded Category 5 (or above) cabling should be used for

all wired Ethernet connections and should be grounded

through the AC ground of the PoE.

We recommend that you protect your networks from

harmful outdoor environments and destructive ESD events

with industrial-grade, shielded Ethernet cable from Ubiquiti

Networks. For more details, visit www.ubnt.com/toughcable

*640-00067-04*

640-00067-04

Installation

1. Align and insert the tabs of the Dish Bracket into the

slots of the Dish Reflector. Rotate the Dish Bracket

counter-clockwise until the tabs lock into place.

2. Line up the Alignment Pins of the Rear Housing with the

alignment holes of the Dish Bracket. Insert the pins and

push until they lock intoplace.

3. Push in the sides of the Cable Door and detach it from the

Rear Housing.

4. Attach the Antenna Feed:

a. Insert the Antenna Feed into the Rear Housing, and push

until it locks into place with a click.

b. Lightly pull the Antenna Feed to ensure that it is locked

into place and the Release button is fully engaged.

Release Button

Bottom View

5. Connect the Ethernet cable:

a. Connect an Ethernet cable to the Ethernet Port of the

Antenna Feed.

b. Re-attach the Cable Door to the Rear Housing.

6. Insert the U-Bolt into the Pole Clamp and Dish Bracket.

Secure each end of the U-Bolt with a Washer and a

FlangeNut.

10 N · m

Note: The mounting assembly can accommodate a

Ø 32 - 56 mm pole.

Connect the power using one of the following options:

• Using the included PoE Adapter: Go to Connecting to the

PoE Adapter.

• Using a separate PoE switch: Connect the Ethernet cable

from the PowerBeam’s Ethernet port to a PoE-enabled

Ethernet port on the switch.

WARNING: The switch port must comply with the

power specifications listed in the Specifications

section of this Quick Start Guide.

Connecting to the PoE Adapter

1. Connect the Ethernet cable from the PowerBeam’s Ethernet

port to the POE port of the PoE Adapter.

2. Connect an Ethernet cable from your LAN to the adapter’s

LAN port.

3. Connect the Power Cord to the adapter’s power port.

Connect the other end of the Power Cord to a power outlet.

Mounting the PoE Adapter (Optional)

1. Remove the PoE Mounting Bracket from the adapter, place

the bracket at the desired location, and mark the two holes.

2. Pre-drill the holes if necessary, and secure the bracket

using two fasteners (not included).

3. Align the adapter’s slots with the tabs of the PoE Mounting

Bracket, and then slide the adapterdown.

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de red de Ubiquiti

Ubiquiti

Ubiquiti uFiber OLT 4 Manual de usuario

Ubiquiti

Ubiquiti 0810354025402 Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-M5-300-IS Manual de usuario

Ubiquiti

Ubiquiti R5AC-PTP Manual de usuario

Ubiquiti

Ubiquiti NanoBeam M Manual de usuario

Ubiquiti

Ubiquiti Nano G Manual de usuario

Ubiquiti

Ubiquiti U6-MESH Manual de usuario

Ubiquiti

Ubiquiti EdgeSwtch 5XP Manual de usuario

Ubiquiti

Ubiquiti PowerBeam AC Gen2 Manual de usuario

Ubiquiti

Ubiquiti UniFi LED ULED-AT Manual de usuario

Ubiquiti

Ubiquiti RocketM Series Manual de usuario

Ubiquiti

Ubiquiti mFi mPort Manual de usuario

Ubiquiti

Ubiquiti airFiber 60 Manual de usuario

Ubiquiti

Ubiquiti RocketDish RD-5G30 Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-500 Manual de usuario

Ubiquiti

Ubiquiti mPort-S mPort Serial Manual de usuario

Ubiquiti

Ubiquiti UniFi Cloud Key Gen2 Plus Manual de usuario

Ubiquiti

Ubiquiti airMAX NanoStationM2 Manual de usuario

Ubiquiti

Ubiquiti UniFi US-24-250W Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-Gen2 Manual de usuario

Ubiquiti

Ubiquiti PowerBeam PBE-5AC-400-ISO Manual de usuario

Ubiquiti

Ubiquiti UniFi Dream Machine Pro Manual de usuario

Ubiquiti

Ubiquiti USW-Flex-Mini Manual de usuario

Ubiquiti

Ubiquiti RD-3G26 Manual de usuario

Manuales populares de Hardware de red de otras marcas

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manual de usuario

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manual de usuario

Yudor

Yudor YDS-16 Manual de usuario

D-Link

D-Link ShareCenter DNS-320L Manual de usuario

Samsung

Samsung ES1642dc Instrucciones de uso

Honeywell Home

Honeywell Home LTEM-PV Instrucciones de montaje

evertz

evertz 7700 Series Manual de usuario

D-Link

D-Link ShareCenter DNS-343 Manual de usuario

Asante

Asante AsanteBridge 1012 Manual de usuario

FireBrick

FireBrick FB2700 Manual de usuario

Audiovox Electronics

Audiovox Electronics ARWH2T Manual de usuario

ADC

ADC DSX-1 Manual

NetComm

NetComm NF2 Manual de usuario

Alcatel-Lucent

Alcatel-Lucent 5620 Manual de usuario

Dell EMC

Dell EMC XC6420 Series Manual de usuario

Lanner

Lanner NCA-1020A Manual de usuario

Allied Telesis

Allied Telesis AT-TN121-A Manual de usuario

Arista

Arista CCA-ETM-Q12 Manual de usuario