TSI Instruments AVM430 Manual de operación

VELOCICALC®

AIR VELOCITY METER

MODEL 9565 SERIES

OPERATION AND SERVICE MANUAL

P/N 6004851, REVISION F

JUNE 2018

www. .com information@itm.com1.800.561.8187

Address

TSI Incorporated / 500 Cardigan Road / Shoreview, MN 55126 / USA

Fax No.

(651) 490-3824

Limitation Of Warranty And Liability (effective February 2015)

Seller warrants the goods, excluding software, sold hereunder, under normal use and

service as described in the operator's manual, to be free from defects in workmanship

and material for 24 months, or if less, the length of time specified in the operator's

manual, from the date of shipment to the customer. This warranty period is inclusive of

any statutory warranty. This limited warranty is subject to the following exclusions and

exceptions:

a. Hot-wire or hot-film sensors used with research anemometers, and certain other

components when indicated in specifications, are warranted for 90 days from the date

of shipment;

b. Carbon monoxide (CO) Electro-chemical sensors are warranted for 12 months from

the date of shipment.

c. Pumps are warranted for hours of operation as set forth in product or operator’s

manuals;

d. Parts repaired or replaced as a result of repair services are warranted to be free from

defects in workmanship and material, under normal use, for 90 days from the date of

shipment;

e. Seller does not provide any warranty on finished goods manufactured by others or on

any fuses, batteries or other consumable materials. Only the original manufacturer's

warranty applies;

f. This warranty does not cover calibration requirements, and seller warrants only that

the instrument or product is properly calibrated at the time of its manufacture.

Instruments returned for calibration are not covered by this warranty;

g. This warranty is VOID if the instrument is opened by anyone other than a factory

authorized service center with the one exception where requirements set forth in the

manual allow an operator to replace consumables or perform recommended

cleaning;

h. This warranty is VOID if the product has been misused, neglected, subjected to

accidental or intentional damage, or is not properly installed, maintained, or cleaned

according to the requirements of the manual. Unless specifically authorized in a

separate writing by Seller, Seller makes no warranty with respect to, and shall have no

liability in connection with, goods which are incorporated into other products or

equipment, or which are modified by any person other than Seller.

The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS

stated herein. NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR

PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE. WITH RESPECT TO

SELLER’S BREACH OF THE IMPLIED WARRANTY AGAINST INFRINGEMENT,

SAID WARRANTY IS LIMITED TO CLAIMS OF DIRECT INFRINGEMENT AND

EXCLUDES CLAIMS OF CONTRIBUTORY OR INDUCED INFRINGEMENTS.

BUYER’S EXCLUSIVE REMEDY SHALL BE THE RETURN OF THE PURCHASE

PRICE DISCOUNTED FOR REASONABLE WEAR AND TEAR OR AT SELLER’S

OPTION REPLACEMENT OF THE GOODS WITH NON-INFRINGING GOODS.

TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER

OR BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES,

www. .com information@itm.com1.800.561.8187

INJURIES, OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS

BASED ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR

OTHERWISE) SHALL BE THE RETURN OF GOODS TO SELLER AND THE

REFUND OF THE PURCHASE PRICE, OR, AT THE OPTION OF SELLER, THE

REPAIR OR REPLACEMENT OF THE GOODS. IN THE CASE OF SOFTWARE,

SELLER WILL REPAIR OR REPLACE DEFECTIVE SOFTWARE OR IF UNABLE TO

DO SO, WILL REFUND THE PURCHASE PRICE OF THE SOFTWARE. IN NO

EVENT SHALL SELLER BE LIABLE FOR LOST PROFITS, BUSINESS

INTERRUPTION, OR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR

INCIDENTAL DAMAGES. SELLER SHALL NOT BE RESPONSIBLE FOR

INSTALLATION, DISMANTLING OR REINSTALLATION COSTS OR CHARGES. No

Action, regardless of form, may be brought against Seller more than 12 months after a

cause of action has accrued. The goods returned under warranty to Seller's factory

shall be at Buyer's risk of loss, and will be returned, if at all, at Seller's risk of loss.

Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY

AND LIABILITY, which contains the complete and exclusive limited warranty of Seller.

This LIMITATION OF WARRANTY AND LIABILITY may not be amended, modified or

its terms waived, except by writing signed by an Officer of Seller.

Service Policy

Knowing that inoperative or defective instruments are as detrimental to TSI as they are

to our customers, our service policy is designed to give prompt attention to any

problems. If any malfunction is discovered, please contact your nearest sales office or

representative, or call Customer Service department at (800) 874-2811 (USA) or (1)

651-490-2811 (International).

www. .com information@itm.com1.800.561.8187

iii

CONTENTS

CHAPTER 1 UNPACKING AND PARTS IDENTIFICATION ............. 1

Bluetooth® Safety and Compliance................................................. 1

CHAPTER 2 SETTING-UP ................................................................. 5

Supplying Power to the Model 9565 Series .................................... 5

Installing the Batteries ............................................................... 5

DIP Switch Settings ................................................................... 5

Using the AC Adapter ................................................................ 6

Connecting Ventilation or IAQ Probes ............................................ 7

Using the Telescoping Thermoanemometer Probes ...................... 7

Extending the Probe .................................................................. 7

Retracting the Probe .................................................................. 7

Using the Pressure Ports (9565-P) ................................................. 8

Connecting the Static Pressure Probe ...................................... 8

Connecting an Optional Pitot Probe or Airflow (straight

pitot) Probe ............................................................................ 9

Thermocouple Ports ..................................................................... 10

Connecting the Thermocouples .............................................. 10

Connecting the Optional Bluetooth Portable Printer Device

(Models 9565-P and 9565-X only) ............................................. 11

Connecting to a Computer ............................................................ 11

CHAPTER 3 OPERATION ............................................................... 13

Keypad Functions ......................................................................... 13

Common Terms ............................................................................ 14

Menus ........................................................................................... 15

ZERO PRESSURE ............................................................................. 15

DISPLAY SETUP ............................................................................... 16

SETTINGS ....................................................................................... 17

FLOW SET UP .................................................................................. 17

VOC SETUP ..................................................................................... 19

ACTUAL/STANDARD SETUP .............................................................. 20

DATA LOGGING ............................................................................... 21

Measurements ......................................................................... 21

Log Mode/Log Settings ............................................................ 21

Choose Test ............................................................................ 27

Name Test ............................................................................... 27

View Data ................................................................................ 28

View Stats ................................................................................ 28

View Samples .......................................................................... 29

Print Test ................................................................................. 30

Delete Data .............................................................................. 31

% Memory................................................................................ 32

www. .com information@itm.com1.800.561.8187

ZERO CO ......................................................................................... 33

APPLICATIONS ................................................................................. 34

CALIBRATION .................................................................................. 35

BLUETOOTH FUNCTIONS (Models 9565-P and 9565-X only) ..................... 35

Discover Devices ..................................................................... 35

Discoverability .......................................................................... 36

PINcode ................................................................................... 36

# AutoConnects ....................................................................... 36

Printing Data Using the Portable Printer (Models 9565-P and

9565-X only) ............................................................................... 36

TrakPro™ Data Analysis Software ............................................... 37

LogDat2™ Downloading Software ................................................ 37

CHAPTER 4 MAINTENANCE .......................................................... 39

Recalibration ................................................................................. 39

Cases ............................................................................................ 39

Storage .......................................................................................... 39

CHAPTER 5 TROUBLESHOOTING ................................................ 41

APPENDIX A SPECIFICATIONS ..................................................... 43

APPENDIX B OPTIONAL PLUG-IN PROBES ................................ 47

www. .com information@itm.com1.800.561.8187

Chapter 1

Unpacking and Parts Identification

Carefully unpack the instrument and accessories from the shipping

container. Check the individual parts against the list of components

below. If anything is missing or damaged, notify TSI immediately.

1. Carrying case

2. Instrument

3. Static pressure tip (9565-P and 9565-P-NB models only)

4. Rubber tubing (9565-P and 9565-P-NB models only)

5. USB cable

6. TrakPro CD-ROM with data analysis software

7. LogDat2 CD-ROM with downloading software

8. AC adapter

This manual supports the following models:

Model

Description

9565-P

Multi-Function Ventilation Meter with Differential

Pressure Sensor

9565-P-NB

Multi-Function Ventilation Meter with Differential

Pressure Sensor, No Bluetooth

9565-X

Multi-Function Ventilation Meter, No Differential

Pressure Sensor

9565-X-NB

Multi-Function Ventilation Meter, No Differential

Pressure Sensor, No Bluetooth

Bluetooth® Safety and Compliance

This product uses Classic Bluetooth® v2.0 to communicate with

software applications.

Hereby, TSI Inc. declares that this Classic Bluetooth® test and

measurement instrument is in compliance with Directive 2014/53/EC.

Transmit Power Rating is +4 dBm, MAX @ 2.4 – 2.5 GHz.

www. .com information@itm.com1.800.561.8187

Chapter 1

NO TE

This device may not cause interference; this device must accept

any interference, including interference that may cause undesired

operation of the device.

l’appareil ne doit pas produire de brouillage; l’appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est

susceptible d’en compromettre le fonctionnement.

NO TE

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to part 15 of the FCC Rules

(FCC ID: PI4411B). These limits are designed to provide

reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does

cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for

help.

NO TE

This device complies with Industry Canada licence-exempt RSS

standard(s). Operation is subject to the following two conditions: (1)

this device may not cause interference, and (2) this device must

accept any interference, including interference that may cause

undesired operation of the device.

www. .com information@itm.com1.800.561.8187

W A R N I N G

Changes or modifications not expressly approved by

the party responsible for compliance could void the

user's authority to operate the equipment.

www. .com information@itm.com1.800.561.8187

Chapter 2

Setting-up

Supplying Power to the Model 9565 Series

The Model 9565 VelociCalc® Air Velocity Meter can be powered in

one of two ways: four size AA batteries or the AC adapter.

Installing the Batteries

Insert four AA batteries as indicated by the diagram located on

the inside of the battery compartment. The Model 9565 is

designed to operate with either alkaline or NiMH rechargeable

batteries. Battery life will be shorter if NiMH batteries are used. If

NiMH batteries are used the DIP switch will need to be changed.

Refer to the next section, DIP Switch Settings. Carbon-zinc

batteries are not recommended because of the danger of battery

acid leakage.

DIP Switch Settings

To access the DIP switch, remove the batteries from the battery

compartment. On the inside of the battery compartment, there is

a window with a single DIP switch (see figure below). The table

below shows the functions for the switch.

C a u t i o n

Make certain that power is turned off before changing

the DIP switch settings.

Switch

Function

Settings

NiMH

OFF: Alkaline Batteries

ON: NiMH Rechargeable Batteries

VelociCalc is a registered trademark of TSI Incorporated.

www. .com information@itm.com1.800.561.8187

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de TSI Instruments

TSI Instruments

TSI Instruments 9555 Series Manual de operación

TSI Instruments

TSI Instruments dusttrak II 8530 Manual de operación

TSI Instruments

TSI Instruments Quest The Edge Manual de usuario

TSI Instruments

TSI Instruments EG4 Manual de usuario

TSI Instruments

TSI Instruments AIRASSURE 8144 Manual de usuario

TSI Instruments

TSI Instruments 3302A Manual de usuario

TSI Instruments

TSI Instruments IAQ50 Manual de usuario

TSI Instruments

TSI Instruments HM685 Manual de usuario

TSI Instruments

TSI Instruments ALNOR HM670 Manual de usuario

TSI Instruments

TSI Instruments HM675 Instrucciones de funcionamiento y mantenimiento

TSI Instruments

TSI Instruments 3080 Series Manual de operación

TSI Instruments

TSI Instruments 5200 Series Manual de usuario

TSI Instruments

TSI Instruments DustTrak 8520 Instrucciones de instalación y funcionamiento

TSI Instruments

TSI Instruments 3082 Manual de usuario

TSI Instruments

TSI Instruments PORTACOUNT 8020 Instrucciones de instalación y funcionamiento

TSI Instruments

TSI Instruments IAQ-CALC 7525 Manual de usuario

TSI Instruments

TSI Instruments AIRASSURE 8144 Manual de usuario

TSI Instruments

TSI Instruments 4000 Series Guía

TSI Instruments

TSI Instruments SIZER 3321 Manual de usuario

TSI Instruments

TSI Instruments VELOCICALC 5725 Manual de operación

TSI Instruments

TSI Instruments VelociCheck 8330 Manual de operación

TSI Instruments

TSI Instruments Quest Edge 7 Manual de usuario

TSI Instruments

TSI Instruments Alnor RVA801 Manual de operación

TSI Instruments

TSI Instruments Aerotrak 9303 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario