TSI Instruments Aerotrak 9303 Manual de usuario

QUICK START GUIDE

AEROTRAK®HANDHELD

AIRBORNE PARTICLE COUNTER

MODEL 9303

Thank you for purchasing a TSI AeroTrak®Model 9303

Handheld Airborne Particle Counter (particle counter).

This guide will help you quickly begin using your particle

counter.

More detailed information is in the manual located on

the included TrakPro™Lite Secure Software CD.

Please refer to the Operation Manual if you have

questions on the operation of your new particle counter.

Safety

This section gives instructions to promote safe and

proper handling of the AeroTrak®Handheld Airborne

Particle Counters.

I M P O R T A N T

There are no user-serviceable parts inside the

instrument. Refer all repair and maintenance to a

qualified factory-authorized technician. All

maintenance and repair information in this manual is

included for use by a qualified factory-authorized

technician.

L A S E R S A F E T Y

The Model 9303 Handheld Airborne Particle Counter

is a Class I laser-based instrument. During normal

operation, you will not be exposed to laser radiation.

However, precaution should be taken to avoid

exposure to hazardous radiation in the form of

intense, focused, visible light. Exposure to this light

may cause blindness. DO NOT remove any parts

from the particle counter unless you are specifically

told to do so in this manual. DO NOT remove the

housing or covers. There are no user-serviceable

components inside the housing.

The use of controls, adjustments, or

procedures other than those specified

in this manual may result in exposure

to hazardous optical radiation.

WARNING

The battery supplied by TSI (700019) has built in

protection against explosion and fire hazard. Do not

use a substitute. Do not use non-rechargeable

batteries in this instrument. Fire, explosions, or other

hazards may result.

Labels

Advisory labels and identification labels are attached to

the outside of the particle counter housing and to the

optics housing on the inside of the instrument.

1. Serial number label

(back panel)

2. Laser radiation label

(internal)

DANGER!

INVISIBLE LASER RADIATION

WHEN

OPEN. AVOID DIRECT

EXPOSURE TO BEAM

WARNING: NO USER SERVICABLE

PARTS INSIDE. REFER SERVICING

TO QUALIFIED PERSONNEL

3. Laser radiation

symbol label

(internal)

3. European symbol

for non-disposable

item. Item must be

recycled.

Unpacking

1. Carefully unpack the particle counterfrom the

shipping container and verify that all the items listed

in the following table are present.

2. Contact TSI immediately if items are missing or

broken.

-2-

Qty

Item

Description

Part/

Model

Reference Picture

AeroTrak®

Airborne

Particle

Counter

9303-01

AC power

adapter and

country-

specific plugs

700021

Isokinetic inlet

700003

Battery Pack

700019

Computer

cable, USB A

to mini-B

700036

HEPA zero

filter

700005

TrakPro™

Lite Secure

Software CD

for 21 CFR

Part 11

compliant

data

downloading

(includes

manuals)

7001901

Operation

Manual

6002277

Included on

TRAKPRO™Lite

Secure Software CD

Quick Start

Guide

6002238

Calibration

Certificate

N/A

3. Additional items may be included if you ordered

accessories or spare parts.

Power

1. The battery is shipped separately and has to be

installed before use.

2. Remove the battery cover on the back side of the

handle with a screwdriver and connect the battery to

the socket. Replace the battery cover. Do not over-

tighten the screw.

3. Fully charge the battery before use.

4. Select the appropriate country-specific power plug

for the AC power adapter and install the plug.

5. Insert the DC end of the power cord into the DC

Adapter Socket on the particle counter and plug the

power supply into an AC source (100-240 VAC, 50-

60 Hz, 0.6 A).

6. The Power LED lights when the battery is charging.

When the Power LED is off, the battery is fully

charged.

7. When the battery is charged, unplug the

power supply.

-3-

Running the Particle Counter

1. Turn on the unit with the On/Off button.

2. To turn the power off, hold the On/Off button down

for more than 5 seconds. This prevents accidentally

turning off the instrument when using the other

buttons.

3. The Main screen is shown below. Turn the pump on

by pressing the Left Soft Key (under “RUN”).

0.3µm

1.0µm

5.0µm

Loc # 001

0002/1500

Stopped

STime 01:00

HTime 00:05

RUN

4. To access the main menu, press the Right Soft Key

with “MENU” above it. From the Main Menu you can

select submenus:

Settings –to set language, time and date, time

and day format, and screen settings.

Sample Menu –to set sample mode, cycle

mode, sample time, hold time, cycle count,

sample units, and channel 2 size.

Buffer Menu –to view the number of records

stored in the Model 9303, display buffer

records, and clear the buffer.

Utility Menu –to adjust the pump speed, turn

data logging on and off, and select the

sampling location.

5. The submenus are explained in detail in the

Operation Manual.

Navigating Menus

1. You can move between settings on the sub menus

with the Up/Down arrow keys. If a setting has two or

more values, use the Left and Right Soft Keys

(under < and >) to cycle between values.

2. If the setting has more than a few possible values,

then the Left and Right Soft Keys are not available.

Instead, select Enter to display a screen where the

value can be edited with the Up/Down keys as well

as the Left and Right Soft Keys. Use ESC to save

the new value and return to the previous menu.

Set up Time/Date

1. Select MENU to go to the Main Menu and then

select the Settings sub-menu. Set the Time Format

to 12 or 24 hr time format

2. Set the Date Format to DDMMYY or MMDDYY

date format.

3. Use Set Time to enter the current time.

4. Use Set Date to enter the current date.

5. Change the Backlight setting if desired. Press ESC

to return to the Main Menu.

Set Up Sampling

1. From the Main Menu, select Sample Menu.

2. Change settings so they match the example below.

SAMPLE MENU

Sample Mode

COUNTS

Cycle Mode

AUTO

Sample Time

01:00

Hold Time

00:30

Cycle Count

010

Sample Units

LITER

Chan 2 Size

0.5µm

3. Press ESC to return to the Main Menu.

N O T E

When concentration sample mode is used with short

sample times (less than 30 seconds), the

concentration may not be accurate due to the poor

counting & timing statistics associated with a short

sample.

4. Finally, select the Utility Menu and set the Data

Logging mode and Location as shown. DO NOT

change the pump speed.

TSI Incorporated –Visit our website www.tsi.com for more information.

USA Tel: +1 800 874 2811

UK Tel: +44 149 4 459200

France Tel: +33 1 41 19 21 99

Germany Tel: +49 241 523030

India Tel: +91 80 67877200

China Tel: +86 10 8219 7688

Singapore Tel: +65 6595 6388

5. Press ESC twice to return to the Main Screen.

UTILITY MENU

Pump Speed

099

Data Logging

Location

120

Collecting Samples

1. Press RUN using the Left Soft Key. This turns on

the pump and the particle counter runs for 10 cycles

that are one minute long with 30 second hold times

in-between.

2. Use the Buffer Menu to review the data.

Software

1. The TrakPro™Lite Secure Data Transfer utility and

user manuals come on a CD that was packaged with

your particle counter.

2. To install the communications software and drivers,

insert the CD into your computer drive and follow

the on-screen instructions.

3. See the TrakPro™Lite Secure Software User’s

Guide (P/N 6004404) on CD (P/N 7001901) for

installation instructions.

N O T E

Make sure the particle counter is connected before

you run the software.

Checking Flow

1. Periodically check the inlet flow of the instrument

with an external flow meter standard.

2. Connect a flowmeter standard to the inlet and turn

on the instrument.

3. From the main menu, select the Utility menu

4. Select the Pump Speed and move the speed setting

up or down as needed to match the flow standard at

2.83 L/min (0.1 cfm).

5. When the flow is set, select ESC to go back to the

main menu.

6. Disconnect the flowmeter.

Otros manuales para Aerotrak 9303

Otros manuales de Instrumento de medición de TSI Instruments

TSI Instruments

TSI Instruments VelociCalc 9515-AC Manual de operación

TSI Instruments

TSI Instruments 3321 Manual de operación

TSI Instruments

TSI Instruments questemp 48n Manual de usuario

TSI Instruments

TSI Instruments VelociCalc 9545 Manual de operación

TSI Instruments

TSI Instruments DP-CALC 5815 Manual de operación

TSI Instruments

TSI Instruments 4040 Manual de operación

TSI Instruments

TSI Instruments 3080 Series Manual de operación

TSI Instruments

TSI Instruments IAQ50 Manual de usuario

TSI Instruments

TSI Instruments 9565-P Manual de operación

TSI Instruments

TSI Instruments ALNOR 9880 Manual de usuario

TSI Instruments

TSI Instruments ALNOR MicroManometer AXD 550 Manual de usuario

TSI Instruments

TSI Instruments ALNOR AVM440 Manual de operación

TSI Instruments

TSI Instruments ALNOR AXD 530 Manual de usuario

TSI Instruments

TSI Instruments QUESTemp 32 Manual de usuario

TSI Instruments

TSI Instruments 5200 Series Manual de usuario

TSI Instruments

TSI Instruments PORTACOUNT 8020 Instrucciones de instalación y funcionamiento

TSI Instruments

TSI Instruments HM685 Manual de usuario

TSI Instruments

TSI Instruments Quest The Edge Manual de usuario

TSI Instruments

TSI Instruments VELOCICALC 5725 Manual de operación

TSI Instruments

TSI Instruments TF Series Manual de usuario

TSI Instruments

TSI Instruments Flowmaster 250 Guía

TSI Instruments

TSI Instruments VelociCheck 8330 Manual de operación

TSI Instruments

TSI Instruments Cheetah CH-5 Manual de usuario

TSI Instruments

TSI Instruments Q-TRAK XP 7585 Manual de usuario

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario