TSI Instruments Q-Trak XP Manual de operación

Q-TRAK™XP

INDOOR AIR QUALITY MONITOR

MODEL 7585

OPERATION AND SERVICE MANUAL

P/N 6013907, REVISION A

NOVEMBER 2020

Shown with optional battery

cover with tripod mount and

tabletop tripod (P/N 800129)

ii Q-Trak™ XP IAQ Monitor Model 7585

Operation and Service Manual iii

Address

TSI Incorporated / 500 Cardigan Road / Shoreview, MN 55126 / USA

Fax No.

(651) 490-3824

Limitation of Warranty and Liability (effective February 2016)

(For country-specific terms and conditions outside of the USA, please visit www.tsi.com.)

Seller warrants the goods, excluding software, sold hereunder, under normal use and

service as described in the operator's manual, to be free from defects in workmanship

and material for 24 months, or if less, the length of time specified in the operator's

manual, from the date of shipment to the customer. This warranty period is inclusive of

any statutory warranty. This limited warranty is subject to the following exclusions and

exceptions:

a. The following gas sensors are warranted for 12 months from the date of shipment -

carbon dioxide, carbon monoxide, chlorine, hydrogen sulfide, nitric oxide, nitrogen

dioxide, ozone, and TVOC high and low sensors;

b. The following gas sensors are warranted for 6 months from the date of shipment -

ammonia and formaldehyde sensors;

c. Parts repaired or replaced as a result of repair services are warranted to be free

from defects in workmanship and material, under normal use, for 90 days from the

date of shipment;

d. Seller does not provide any warranty on finished goods manufactured by others or on

any fuses, batteries or other consumable materials. Only the original manufacturer's

warranty applies;

e. This warranty does not cover calibration requirements, and seller warrants only that

the instrument or product is properly calibrated at the time of its manufacture.

Instruments returned for calibration are not covered by this warranty;

f. This warranty is VOID if the instrument is opened by anyone other than a

factory authorized service center with the one exception where requirements

set forth in the manual allow an operator to replace consumables or perform

recommended cleaning;

g. This warranty is VOID if the product has been misused, neglected, subjected to

accidental or intentional damage, or is not properly installed, maintained, or cleaned

according to the requirements of the manual. Unless specifically authorized in a

separate writing by Seller, Seller makes no warranty with respect to, and shall have no

liability in connection with, goods which are incorporated into other products or

equipment, or which are modified by any person other than Seller.

The foregoing is IN LIEU OF all other warranties and is subject to the LIMITATIONS

stated herein. NO OTHER EXPRESS OR IMPLIED WARRANTY OF FITNESS FOR

PARTICULAR PURPOSE OR MERCHANTABILITY IS MADE. WITH RESPECT TO

SELLER’S BREACH OF THE IMPLIED WARRANTY AGAINST INFRINGEMENT,

SAID WARRANTY IS LIMITED TO CLAIMS OF DIRECT INFRINGEMENT AND

EXCLUDES CLAIMS OF CONTRIBUTORY OR INDUCED INFRINGEMENTS.

BUYER’S EXCLUSIVE REMEDY SHALL BE THE RETURN OF THE PURCHASE

PRICE DISCOUNTED FOR REASONABLE WEAR AND TEAR OR AT SELLER’S

OPTION REPLACEMENT OF THE GOODS WITH NON-INFRINGING GOODS.

TO THE EXTENT PERMITTED BY LAW, THE EXCLUSIVE REMEDY OF THE USER

OR BUYER, AND THE LIMIT OF SELLER'S LIABILITY FOR ANY AND ALL LOSSES,

INJURIES, OR DAMAGES CONCERNING THE GOODS (INCLUDING CLAIMS

BASED ON CONTRACT, NEGLIGENCE, TORT, STRICT LIABILITY OR

OTHERWISE) SHALL BE THE RETURN OF GOODS TO SELLER AND THE

REFUND OF THE PURCHASE PRICE, OR, AT THE OPTION OF SELLER, THE

iv Q-Trak™ XP IAQ Monitor Model 7585

REPAIR OR REPLACEMENT OF THE GOODS. IN THE CASE OF SOFTWARE,

SELLER WILL REPAIR OR REPLACE DEFECTIVE SOFTWARE OR IF UNABLE TO

DO SO, WILL REFUND THE PURCHASE PRICE OF THE SOFTWARE. IN NO

EVENT SHALL SELLER BE LIABLE FOR LOST PROFITS, BUSINESS

INTERRUPTION, OR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR

INCIDENTAL DAMAGES. SELLER SHALL NOT BE RESPONSIBLE FOR

INSTALLATION, DISMANTLING OR REINSTALLATION COSTS OR CHARGES. No

Action, regardless of form, may be brought against Seller more than 12 months after a

cause of action has accrued. The goods returned under warranty to Seller's factory

shall be at Buyer's risk of loss, and will be returned, if at all, at Seller's risk of loss.

Buyer and all users are deemed to have accepted this LIMITATION OF WARRANTY

AND LIABILITY, which contains the complete and exclusive limited warranty of Seller.

This LIMITATION OF WARRANTY AND LIABILITY may not be amended, modified or

its terms waived, except by writing signed by an Officer of Seller.

Service Policy

Knowing that inoperative or defective instruments are as detrimental to TSI as they are

to our customers, our service policy is designed to give prompt attention to any

problems. If any malfunction is discovered, please contact your nearest sales office or

representative, or call Customer Service department at (800) 680-1220 (USA) or

(1) 651-490-2860 (International).

Trademarks

TSI and TSI logo are registered trademarks of TSI Incorporated in the United States

and may be protected under other country’s trademark registrations. Q-Trak and

TrakPro are trademarks of TSI Incorporated. Wi-Fi is a registered trademark of the

Wi-Fi Alliance.

CONTENTS

CONTENTS .........................................................................................V

SAFETY..............................................................................................IX

Description of Caution/Warning Symbols........................................ ix

Caution......................................................................................... ix

Warning........................................................................................ ix

Caution and Warning Symbols.........................................................x

Battery Safety and Disposal.............................................................x

Laser Safety..................................................................................... xi

Labels ..............................................................................................xii

Reusing and Recycling...................................................................xiv

CHAPTER 1 OVERVIEW...................................................................1

CHAPTER 2 UNPACKING AND PARTS IDENTIFICATION.............3

Standard Equipment.........................................................................3

Optional Gas Sensors.......................................................................5

Optional Accessories........................................................................6

Other Replacement Parts.................................................................6

CHAPTER 3 SETTING UP THE Q-TRAK

™XP MONITOR...............9

Installation of Gas Sensors...............................................................9

Providing Power to the Q-Trak™ XP..............................................10

Operating the Instrument with the AC Adapter ...........................10

Operating the Instrument with the Lithium-Ion Battery................11

Charging the Battery and Calibrating the Power Gauge.............12

Installing and Connecting to Available Wi-Fi®(optional

Wi-Fi® dongle...............................................................................13

Connecting to a Computer and Installing TrakPro™

Ultra Software..............................................................................13

CHAPTER 4 OPERATIONAL OVERVIEW......................................15

Powering ON the Q-Trak™ XP Monitor..........................................15

Navigating the Dashboard Page+ ..................................................17

Main Menu......................................................................................18

Dashboard...................................................................................19

Settings........................................................................................19

Manage Data...............................................................................20

Calibration ...................................................................................20

Workflows....................................................................................21

Device Information.......................................................................22

vi Q-Trak™ XP IAQ Monitor Model 7585

CHAPTER 5 SETTINGS...................................................................23

General Settings.............................................................................24

Date/Time .......................................................................................25

Display/Power Management...........................................................26

Sensors...........................................................................................27

Network Settings.............................................................................28

Units of Measure.............................................................................29

Notifications/Alarms........................................................................30

CHAPTER 6 CALIBRATION............................................................31

Gas Sensors...................................................................................31

Gas Sensor Verification..................................................................31

Gas Calibration Procedure..............................................................33

Step 1 –Select a Gas Sensor for Calibration..............................33

Step 2 –Place the calibration cap onto the gas sensor

you want to calibrate ................................................................34

Step 3 - Select the sensor to be calibrated on the

instrument display ....................................................................34

Step 4 - Perform ZERO Capture .................................................35

Step 5 –Perform SPAN Capture.................................................35

Step 6 –Save or Discard Calibration..........................................36

Gas Calibration Unsuccessful .....................................................37

Built-in Sensor Calibration: Temperature, Relative Humidity,

and Barometric Pressure Sensors...............................................37

Reset Sensors to Default Calibration..............................................39

CHAPTER 7 LOGGING DATA.........................................................41

Logging Data...................................................................................42

Logging Profiles..............................................................................43

Locations.........................................................................................43

Settings...........................................................................................45

Logging Mode..............................................................................45

Sample Interval............................................................................46

Schedules .......................................................................................46

CHAPTER 8 MANAGE DATA..........................................................49

Selecting Log Files..........................................................................49

View Log Files.................................................................................50

Delete Log Files..............................................................................50

Export Log Files..............................................................................51

Edit Log File Names........................................................................52

Scrolling Through Data List.........................................................52

CHAPTER 9 WORKFLOWS ............................................................53

Percent Outside Air (%OA) Calculation Procedure........................53

Operation and Service Manual vii

CHAPTER 10 TRAKPRO™ULTRA SOFTWARE...........................57

CHAPTER 11 UPDATE INSTRUMENT SOFTWARE .....................59

CHAPTER 12 MAINTENANCE........................................................61

Replacing Sensors..........................................................................61

Recalibration...................................................................................61

Removing the Sensor Module from the Handle of the

Q-Trak™XP Monitor....................................................................61

Storage ...........................................................................................63

CHAPTER 13 TROUBLESHOOTING..............................................65

Error Messages ..............................................................................68

CHAPTER 14 HELP..........................................................................71

TSI®Technical Support/Service......................................................71

APPENDIX A SPECIFICATIONS.....................................................73

APPENDIX B DEFINITIONS.............................................................77

viii Q-Trak™ XP IAQ Monitor Model 7585

(This page intentionally left blank)

Safety

This section provides instructions to ensure safe and proper

operation of the Q-Trak™XP Indoor Air Quality Monitor Model 7585.

WARNING

•The instrument must be used in the manner

described in this manual. Failure to follow all of the

procedures described in this manual can result in

serious injury to you or can cause irrevocable

damage to the instrument.

•There are no user-serviceable parts inside the

instrument. Refer all repairs to a qualified factory-

authorized technician.

•The Q-Trak™ XP monitor is not rated for intrinsic

safety. DO NOT operate the Q-Trak™ XP monitor

under conditions where there is a risk of fire or

explosion.

Description of Caution/Warning Symbols

Appropriate caution/warning statements are used throughout the

manual and on the instrument that require you to take cautionary

measures when working with the instrument.

Caution

CAUTION

Failure to follow the procedures prescribed in this

manual might result in irreparable equipment damage.

Important information about the operation and

maintenance of this instrument is included in

this manual.

Warning

WARNING

Warning means that unsafe use of the instrument

could result in serious injury to you or cause damage

to the instrument. Follow the procedures prescribed.

x Q-Trak™ XP IAQ Monitor Model 7585

Caution and Warning Symbols

The following symbols may accompany cautions and warnings to

indicate the nature and consequences of hazards:

Warns that the instrument contains a laser and that

important information about its safe operation and

maintenance is included in the manual.

Warns that the instrument is susceptible to electro-

static discharge (ESD) and ESD protection should be

followed to avoid damage.

Indicates the connector is connected to earth ground

and cabinet ground.

Battery Safety and Disposal

This instrument uses a rechargeable Lithium ion battery with built-in

protection against safety hazards. Always dispose of Li-ion

batteries and transport Li-ion batteries in compliance with

regional regulations.

WARNING

•Use only TSI®supplied batteries in this instrument

(P/N 800123).

•DO NOT abuse the battery in any way as the

battery may rupture or catch fire.

•DO NOT use a substitute or non-rechargeable

battery in this instrument.

•DO NOT short-circuit, incinerate, dismantle or

mutilate Lithium ion batteries.

•DO NOT expose to water or heat.

•DO NOT use any battery which shows signs of

damage, such as bulging, swelling, a swollen

plastic wrap, liquid in the plastic wrap, etc.

Otros manuales para Q-Trak XP

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Instrumento de medición de TSI Instruments

TSI Instruments

TSI Instruments questemp 48n Manual de usuario

TSI Instruments

TSI Instruments ALNOR AVM430A Manual de operación

TSI Instruments

TSI Instruments HM685 Manual de usuario

TSI Instruments

TSI Instruments Alnor Velometer 6000 Series Manual de usuario

TSI Instruments

TSI Instruments DP-CALC 5825 Manual de operación

TSI Instruments

TSI Instruments AIRASSURE 8144 Manual de usuario

TSI Instruments

TSI Instruments ALNOR MicroManometer AXD 550 Manual de usuario

TSI Instruments

TSI Instruments VelociCalc Plus 8384 Manual de operación

TSI Instruments

TSI Instruments Dickey-John MINI GAC 2500 Manual de usuario

TSI Instruments

TSI Instruments Alnor Model AXD620 Manual de operación

TSI Instruments

TSI Instruments 3302A Manual de usuario

TSI Instruments

TSI Instruments 9600 Series Manual de operación

TSI Instruments

TSI Instruments 3936 Manual de operación

TSI Instruments

TSI Instruments ALNOR MicroManometer AXD 550 Manual de usuario

TSI Instruments

TSI Instruments AirPro AP500 Manual de usuario

TSI Instruments

TSI Instruments VelociCheck 8330 Manual de operación

TSI Instruments

TSI Instruments 5200 Series Manual de usuario

TSI Instruments

TSI Instruments 4199 Manual de operación

TSI Instruments

TSI Instruments 9565-P Manual de operación

TSI Instruments

TSI Instruments SIZER 3321 Manual de usuario

TSI Instruments

TSI Instruments Alnor Airflow AXD610 Manual de operación

TSI Instruments

TSI Instruments 3936 SMPS Manual de usuario

TSI Instruments

TSI Instruments BlueSky 8145 Manual de usuario

TSI Instruments

TSI Instruments Alnor RVA801 Manual de operación

Manuales populares de Instrumento de medición de otras marcas

Suaoki

Suaoki D40 Manual de usuario

Elster

Elster BK-G1.6 Manual de usuario

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manual

Duratool

Duratool D03128 Manual de usuario

Vega

Vega VEGAPULS 65 Manual de usuario

Tonghui

Tonghui TH2618B Manual de usuario

Tenmars

Tenmars TM-801 Manual de usuario

MSR

MSR 145 Manual de usuario

TPS

TPS WP-82 Manual de usuario

ELMETRON

ELMETRON CP-511 Manual de usuario

PCB Piezotronics

PCB Piezotronics 003C30 Manual de usuario

Tenma

Tenma 72-10465 Manual de usuario

Endress+Hauser

Endress+Hauser Proline Promag 50 Especificaciones técnicas

Siemens

Siemens SITRANS F Coriolis FCT030 Manual de lista de piezas

KLINGER

KLINGER CMF V Series Manual de usuario

EXFO

EXFO FTB-2 Manual de operación y mantenimiento

Keysight

Keysight M8290A Manual de usuario

ADTEK

ADTEK MW-5 Manual de usuario