TRENDnet TV-H400 Manual de usuario
TV-H400
H/W: V1.0R
Quick Installation Guide
Table of Contents
Version 07.10.2008
English ...................................................................................................... 1
1
2
1. Before You Start
2. Hardware Installation .........................................................................
................................................................................
Troubleshooting ........................................................................................ 9
English
1
1. Before you start
Installation Requirements
Package Contents
The following items below are not included. Users must provide the items
themselves. Make sure to have each item on hand before installation.
?
?
?Power Adapter (12V DC, 0.6A)
?1 x Ceiling Mounting Bracket
?Hexagon screwdriver (1/4” L=6mm)
?Screws and washers
?Rubber seal
TV-H400
Quick Installation Guide
?
?Mounting Screws
?Dry Wall or Wood surface
?Power Cord
?Wire Stripper
?Phillips Screwdriver
?Pliers
?RJ-45 cable
Pan and Tilt Internet Camera Server
2. Hardware Installation
English
2
Note: Configure your Internet Camera Server to match your network before
installing the device.
3. Run all necessary cables (CAT 5
cable, power adapter cable, and
the power terminals) through the
wall mount.
2. Unscrew the thumbscrew to
remove the protective plate from
the wall mount. Save this screw.
You will need to use this screw
later.
1. Rotate the TV-H400's cover
counter clockwise and remove the
cover.
English
3
6. Use the provided rubber seal to
seal the housing.
4. Run each cable through the
opening located at the top of the
TV-H400. DO NOT run all cables
through the opening
simultaneously. Serious blockage
can occur.
7. Slide the protective plating into the
wall mount and tighten the thumb
screw.
5. After inserting the appropriate
cables, extend each cable to 6
inches for camera installation.
English
4
8. Screw the ceiling or wall mount on
top of the TV-H400 with the
provided Allen wrench and three
hexagon socket screws. The
screws are in the plastic bag
labeled Q2 or Q2B.
10. Take the circular base and
connect the three Hex screws to
create this assembly. Then
secure the hex crews with the
nuts. The nuts are in the plastic
bag labeled Q5.
9. Combine the 5cm Hex screws with
the 1cm Hex screws. The 5cm
Hex screws are in the plastic bag
labeled Q3. The 1cm Hex screws
are in the plastic bag labeled Q4.
5
English
13. Connect the remaining two hex
crews to this bracket.
12. Mount this bracket on top of the
three Hex screws, Then using the
three round head screws to
secure the bracket. These screws
are in the plastic bag labeled Q6.
11. Mount the assembly in step 10 to
the camera enclosure using the
three flat head screws. These
screws are in the plastic bag
labeled Q1.
6
English
15. Take the assembly in step 14 and
mount the assembly on top of the
mounting bracket with two round
head screws. These screws are
in the plastic bag labeled Q6.
16. Connect the Ethernet cable and
power adapter to the Internet
Camera Server.
14. Attach the mounting plate for the
camera with 3 small screws.
These screws should come with
the Internet Camera Server.
7
English
19. Plug the power to the Internet
Camera Server and the camera
enclosure into an available power
outlet.
18. Connect the power terminal to the
provided 12V DC, 0.6A power
adapter.
Your installation is now complete.
Register Your Product
To ensure the highest level of customer service and support, please take a moment to
register your product Online at: www.trendnet.com/register
Thank you for choosing TRENDnet
For detailed information regarding the TV-H400 configuration and advanced
settings, please visit TRENDnet's website at www.trendnet.com
17. Place the TV-H400's cover over
the camera and rotate the cover
clock-wise.
8
English
Mounting the Camera Enclosure
1. Place the mounting bracket against
the wall or ceiling and mark each
of the four holes with a pencil.
3. Insert screw anchors into the
holes.
Note: Mounting screws and screw anchors are not included.
2. Drill holes for the screws at each
marked position.
4. Align the wall or ceiling mount
bracket with the screws, and then
use nuts and washers to secure it.
Otros manuales para TV-H400
2
Tabla de contenidos
Otros manuales de Cámara de seguridad de TRENDnet
TRENDnet
TRENDnet TV-IP851WC Manual de usuario
TRENDnet
TRENDnet TV-IP343PI Manual de usuario
TRENDnet
TRENDnet TV-IP342PI Manual de usuario
TRENDnet
TRENDnet TV-IP422 Manual de usuario
TRENDnet
TRENDnet TV-IP201 Manual de usuario
TRENDnet
TRENDnet TV-IP420P Manual de usuario
TRENDnet
TRENDnet TV-IP321PI Manual de usuario
TRENDnet
TRENDnet TV-IP410WN Manual de usuario
TRENDnet
TRENDnet TV-IP662PI Manual de usuario
TRENDnet
TRENDnet TV-IP751WIC Manual de usuario
TRENDnet
TRENDnet TV-IP100-N Manual de usuario
TRENDnet
TRENDnet TV-IP460PI Manual de usuario
TRENDnet
TRENDnet TV-IP252P - SecurView PoE Dome Internet Camera... Manual de usuario
TRENDnet
TRENDnet TV-IP400 Manual de usuario
TRENDnet
TRENDnet TV-IP310PI Manual de usuario
TRENDnet
TRENDnet TV-IP551WI Manual de usuario
TRENDnet
TRENDnet TV-IP501W Manual de usuario
TRENDnet
TRENDnet TV-IP121W Manual de usuario
TRENDnet
TRENDnet TV-IP651WI Manual de usuario
TRENDnet
TRENDnet TV-IP201 Manual de usuario
