Texas Instruments BoosterPack BOOSTXL-RS232 Manual de usuario

BOOSTXL-RS232 BoosterPack™ Hardware

User's Guide

Literature Number: SLLU250

November 2016

2SLLU250–November 2016

Submit Documentation Feedback

Table of Contents

Contents

1 Trademarks......................................................................................................................... 4

2 Introduction......................................................................................................................... 4

2.1 Overview .................................................................................................................. 4

3 Hardware Description........................................................................................................... 5

3.1 Top and Bottom View.................................................................................................... 5

3.2 Board Overview .......................................................................................................... 5

3.3 Block Diagram............................................................................................................ 6

3.4 DB9 Connector ........................................................................................................... 7

3.5 Header Descriptions..................................................................................................... 8

3.6 LED Description......................................................................................................... 10

4 Functional Modes............................................................................................................... 11

4.1 Auto-Powerdown Plus.................................................................................................. 11

4.2 Forced On ............................................................................................................... 11

4.3 Forced Off ............................................................................................................... 11

4.4 Invalid .................................................................................................................... 12

5 Interfacing with External Hardware....................................................................................... 13

6 Additional Information ........................................................................................................ 14

6.1 Design Files ............................................................................................................. 14

6.2 Hardware Change Log................................................................................................. 14

6.3 Schematic................................................................................................................ 14

6.4 PCB Layout.............................................................................................................. 15

www.ti.com

SLLU250–November 2016

List of Figures

1 BOOSTXL-RS232 ........................................................................................................... 4

2 Top View of BOOSTXL-RS232 ............................................................................................ 5

3 Bottom View of BOOSTXL-RS232 ........................................................................................ 5

4 BOOSTXL-RS232 Overview ............................................................................................... 5

5 BOOSTXL-RS232 Block Diagram......................................................................................... 6

6 DB9 Pinout.................................................................................................................... 7

7 GPIO Headers................................................................................................................ 8

8 Header J9..................................................................................................................... 9

9 Supply Select................................................................................................................. 9

10 RS232 LEDs ................................................................................................................ 10

11 Interfacing With LaunchPad............................................................................................... 13

12 BOOSTXL-RS232 Schematic (Zoom for Higher Resolution)......................................................... 14

13 Top Layer Routing ......................................................................................................... 15

14 Bottom Layer Routing...................................................................................................... 15

List of Tables

1 RS-232 Female DB9 Connector Pin Summary.......................................................................... 7

2 Driver Functions............................................................................................................ 11

3 Receiver Functions......................................................................................................... 11

4 INVALID Status............................................................................................................. 12

5 Description of Hardware Changes ....................................................................................... 14

4SLLU250–November 2016

Submit Documentation Feedback

BOOSTXL-RS232 BoosterPack™ Hardware

User's Guide

SLLU250–November 2016

BOOSTXL-RS232 BoosterPack™ Hardware

1 Trademarks

BoosterPack, LaunchPad are trademarks of Texas Instruments.

All other trademarks are the property of their respective owners.

2 Introduction

2.1 Overview

The RS232 BoosterPack provides the opportunity to communicate to and from a TI LaunchPad™ using

the RS232 serial protocol. This opens new capabilities for the microcontrollers to interface with industrial

equipment for debugging, for accessing memory directly for backup recovery, and for simplified data

transfer between systems with proprietary code.

The featured product is the TRS3122E, an ultra-low power, high-speed dual RS232 transceiver. It

supports data [RX, TX] channels as well as flow control [RTS, CTS] channels that can be easily assigned

to 1 of 10 general purpose input/output (GPIO) pins. These channels on the TRS3122E can be configured

to be either one set of data channels and one set of control channels for flow control or to be two sets of

data channels. However, this BoosterPack is configured for one set of data channels [RX, TX] and one set

of control channels [RTS, CTS]. With its unique doubler and tripler charge pump architecture, the

TRS3122E can operate at a VCC as low as 1.8 V while maintaining compatibility with 3.3-V and 5-V

supplies. This BoosterPack allows for operating voltages of 1.8 V or 3.3 V.

This device features a shutdown mode that reduces supply current as low as 0.5 µA. This can be done

manually or by setting the TRS3122E into its Auto-Powerdown Plus mode. See Section 4 for more

information on the modes of operation of the TRS3122E along with how to set up the BoosterPack for

these modes.

2.1.1 What Is Included?

• 1× RS232 BoosterPack

• 7× Shunt Jumper

Figure 1 is a photo of the BOOSTXL-RS232 board.

Figure 1. BOOSTXL-RS232

Female DB9 Connector

Green/Red

LEDs for RX1 &

RTS1

Green/Red

LEDs for TX1

& CTS1

TRS3122E

RS232

Transceiver

LP2985-18 LDO

& J12 Header for

VCC Select

J9 Header for

FORCEON,

FORCEOFF, &

INVALID Selects

J1, J3 Standard BoosterPack

Headers

J7, J8 GPIO Select Headers

J4, J2 Standard BoosterPack

Headers

J5, J6 GPIO Select Headers

www.ti.com

Hardware Description

SLLU250–November 2016

BOOSTXL-RS232 BoosterPack™ Hardware

3 Hardware Description

3.1 Top and Bottom View

Figure 2 is a top view of the BOOSTXL-RS232 and Figure 3 is a bottom view of the BOOSTXL-RS232.

Figure 2. Top View of BOOSTXL-RS232 Figure 3. Bottom View of BOOSTXL-RS232

3.2 Board Overview

Figure 4 shows an overview of the BOOSTXL-RS232 BoosterPack. The main features such as devices,

connectors, headers, and LEDs are highlighted.

See Section 3.4,Section 3.5, and Section 3.6 for additional details regarding each portion of the board.

Figure 4. BOOSTXL-RS232 Overview

40-Pin

BoosterPackTM

Interface

LP2985-18

GND GND

3-Pin Vcc

Select

2 × 30-Pin GPIO

Select

GND

6-Pin Functional

Mode/Invalid

Select

LaunchPadTM BOOSTXL-RS232

3V3

1V8

Vcc

RX1

RTS1

TX1

CTS1

GPIO

FORCEON

FORCEOFF

INVALID

LaunchPad TRS3122E

GPIO

Female

DB9

GND

Hardware Description

www.ti.com

6SLLU250–November 2016

Submit Documentation Feedback

BOOSTXL-RS232 BoosterPack™ Hardware

3.3 Block Diagram

Figure 5 details a block diagram of the BOOSTXL-RS232 BoosterPack. The 40-pin BoosterPack header

allows the BoosterPack to be easily interfaced with LaunchPads. A 3-pin header is available to change

VCC/VLbetween 3.3 V and 1.8 V. This allows the BoosterPack to communicate with LaunchPads either at

3.3-V or 1.8-V logic levels. See Section 3.5.4 for more details. The two 30-pin GPIO headers allow for the

selection of GPIO pins on the LaunchPad to be connected to the TRS3122E. See Section 3.5.1 for more

information. A 6-pin header is available to allow for the FORCEON, FORCEOFF, and INVALID pins on the

TRS3122E to be connected to LaunchPad GPIO pins for more control. See Section 3.5.2 and

Section 3.5.3 for more information.

Figure 5. BOOSTXL-RS232 Block Diagram

www.ti.com

Hardware Description

SLLU250–November 2016

BOOSTXL-RS232 BoosterPack™ Hardware

3.4 DB9 Connector

The BoosterPack includes a female data circuit-terminating equipment (DCE) DB9 port. Female DCE

ports are designed to connect with the male data terminal equipment (DTE) port of the computer. The

labeling for Figure 6 is from the perspective of the computer with the DTE port. Therefore, RX1 is actually

an output from the BoosterPack to the connected device through the RS232 interface, while TX1 is an

input from the connected device to the BoosterPack through the RS232 interface. The same applies to the

RTS1 (input) and CTS1 (output) ports. The RX2, TX2, CTS2, and RTS2 ports are used to interface with

the microcontroller through 0-V to 3.3-V (or 1.8-V) TTL signals. See Table 1 for information on how the

DB9 connector is routed on the BOOSTXL-RS232 BoosterPack.

Figure 6. DB9 Pinout

Table 1. RS-232 Female DB9 Connector Pin Summary

Pin Function

1 NC

2 UART Receive 1 (RX1)

3 UART Transmit 1 (TX1)

4 Shorted to pin 6 (unused flow control line)

5 GND

6 Shorted to pin 4 (unused flow control line)

7 Request to Send 1 (RTS1)

8 Clear to Send 1 (CTS1)

9 NC

Hardware Description

www.ti.com

8SLLU250–November 2016

Submit Documentation Feedback

BOOSTXL-RS232 BoosterPack™ Hardware

3.5 Header Descriptions

3.5.1 Using J5, J6 and J7, J8 GPIO Headers

The J5, J6 and J7, J8 10 × 3 headers are for assigning the TRS3122E UART Drivers or Receivers

(labeled as CTS2, RX2, RTS2, and TX2 on the BoosterPack) to various LaunchPad GPIOs. The default

jumper setup has TX2, RX2, RTS2, and CTS2 assigned to LaunchPad GPIO pins GP3, GP4, GP5, and

GP8, respectively. TI recommends tying TX2 and RX2 to GP3 and GP4, respectively, since GP3 and GP4

are typically the UART transmit and receive ports on TI LaunchPads, this is not required but should be

kept in mind. RTS2 and CTS2 can be connected to any desired GPIO pin.

Each pin of the middle column of the 10 × 3 headers correlates to a particular GPIO pin. The pin it is

connected to is labeled in between the J5, J6 and J7, J8 header groups, this is seen in Figure 7. The

columns on either side of the middle column are connected to their coinciding transceiver pins, which are

labeled at the bottom of each column, this is seen in Figure 7. For example, looking at header J5, J6 in

Figure 7, the right column coincides with RX2. Placing a jumper across the first pins of the middle column

and the right column would short GP3 from the LaunchPad to the DIN1 pin on the TRS3122E.

NOTE: See Section 5 for information on headers J1-4 and how they interface with the LaunchPad

ecosystem.

NOTE: See Figure 13 and Figure 14 for more clarification of how the headers are routed.

Figure 7. GPIO Headers

3.5.2 Utilizing FORCEON and FORCEOFF

The J9 3 × 2 header allows for the option to assign FORCEON and FORCEOFF to GP19 and GP18,

respectively. FORCEON can be connected to GP19 by placing a jumper across pins 1 and 2 on J9 and

FORCEOFF can be connected to GP18 by placing a jumper across pins 3 and 4 on J9, see Figure 8. This

allows for the control of the different functional modes of the TRS3122E. See Section 4 to learn more

about the different functional modes and how to control them using FORCEON and FORCEOFF.

NOTE: If FORCEON and FORCEOFF are not intended to be controlled, then remove the jumpers

discussed.

www.ti.com

Hardware Description

SLLU250–November 2016

BOOSTXL-RS232 BoosterPack™ Hardware

Figure 8. Header J9

3.5.3 Utilizing INVALID Signal

The J9 3 × 2 header also allows for the option to monitor the INVALID pin of the TRS3122E by linking it to

a GPIO pin on a LaunchPad. By placing a jumper across pins 5 and 6 on J9, see Figure 8, the INVALID

pin will be connected to GP14. The GPIO port on a LaunchPad can then be set to an input and used to

monitor the INVALID pin. See Section 4.4 to learn more about the INVALID pin.

NOTE: If the INVALID pin is not intended to be monitored, remove the jumper.

3.5.4 Assigning Desired Supply Voltage

The BOOSTXL-RS232 BoosterPack is populated with a linear regulator to drop the typical 3.3-V VCC on

most LaunchPads to 1.8 V. This allows for communication with LaunchPads that are capable of

communicating at 1.8-V logic levels. To switch between a 1.8-V and 3.3-V supply, use a jumper on J12 to

short the center VCC pin to the desired supply voltage, see Figure 9. A short between pin 1 and 2 results in

3.3-V VCC and a short between 2 and 3 results in 1.8-V VCC. Pin 1 on J12 is denoted with a white line

along one edge of the pin, as seen in Figure 9. While VLand VCC are independent on the TRS3122E

device itself, these two pins are tied together on the BoosterPack. This way VLcannot accidentally be set

higher than VCC. This option was added to display the ultra-low voltage capabilities of the TRS3122E.

NOTE: VCC and VLshould only be set to 1.8 V if the BOOSTXL-RS232 is intended to interface with a

LaunchPad that operates at 1.8-V logic levels. Otherwise TI recommends leaving the jumper

across pins 1 and 2 of J12.

Figure 9. Supply Select

Hardware Description

www.ti.com

10 SLLU250–November 2016

Submit Documentation Feedback

BOOSTXL-RS232 BoosterPack™ Hardware

3.6 LED Description

For this BoosterPack, there are two LEDs per RS232 line (RTS1, RX1, CTS1, TX1) and one power

indication LED, see Figure 10. The LEDs serve as a reference when connecting the BoosterPack to a

LaunchPad and up to a RS232 serial port. A red LED for an RS232 line indicates negative voltage or a

LOW signal, while a green LED indicates positive voltage or a HIGH signal. This information is also

denoted next to each LED; a '+' sign for the green LED and a '-' sign for the red LED. Upon powering the

BoosterPack, the power LED will turn on and the driver and receiver line LEDs may also be on, depending

on what the board is connected to.

Since RS232 TX and RX lines sit at a LOW voltage level until data is transmitted or received, the red LED

for TX1 and RX1 on the board will be on until data is transmitted or received. While transmitting or

receiving, the green LED will blink for the line in use. End of transmission is indicated with just a red LED.

The RTS1 green LED will be on when a request-to-send signal is raised and the CTS1 green LED will be

on when the clear-to-send signal is raised. Otherwise, the red LEDs will be on.

Figure 10. RS232 LEDs

Otros manuales para BoosterPack BOOSTXL-RS232

Tabla de contenidos

Otros manuales de Hardware de computadora de Texas Instruments

Texas Instruments

Texas Instruments MCT8317 Manual de usuario

Texas Instruments

Texas Instruments HVL038 Manual de usuario

Texas Instruments

Texas Instruments TMS320C642x DSP Manual de usuario

Texas Instruments

Texas Instruments TMS320DM355 Manual de usuario

Texas Instruments

Texas Instruments EZShunt INA740 Manual de usuario

Texas Instruments

Texas Instruments TPS65381EVM Manual de usuario

Texas Instruments

Texas Instruments DS250DF810EVM Manual de usuario

Texas Instruments

Texas Instruments BT-MSPAUDSOURCE-RD Manual de usuario

Texas Instruments

Texas Instruments OMAP-L137 EVM Manual de usuario

Texas Instruments

Texas Instruments Sub-1 GHz Sensor-to-Cloud Linux E14 Kit Manual de usuario

Texas Instruments

Texas Instruments TMS320DM357 Manual de usuario

Texas Instruments

Texas Instruments bq27220 Manual del producto

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-ADS7142-Q1 Manual de usuario

Texas Instruments

Texas Instruments TMS320DM646x Manual de usuario

Texas Instruments

Texas Instruments SimpleLink CC2640 Manual de usuario

Texas Instruments

Texas Instruments controlCARD TMDSCNCD2800137 Manual de usuario

Texas Instruments

Texas Instruments TPS62065 Manual de usuario

Texas Instruments

Texas Instruments EDMA3 Manual de usuario

Texas Instruments

Texas Instruments TPS650231EVM Manual de usuario

Texas Instruments

Texas Instruments SimpleLink CC3200 Wi-Fi Manual de usuario

Texas Instruments

Texas Instruments LDC3114-Q1 Manual de usuario

Texas Instruments

Texas Instruments AM1808 Manual del producto

Texas Instruments

Texas Instruments INA229 Manual de usuario

Texas Instruments

Texas Instruments ADS61B23EVM Manual de usuario

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario