Texas Instruments DS250DF810EVM Manual de usuario

SNLU180C–August 2015–Revised September 2019

DS250DF810EVM User’s Guide

User's Guide

SNLU180C–August 2015–Revised September 2019

DS250DF810EVM User’s Guide

The DS250DF810 is an eight-channel multi-rate retimer with integrated signal conditioning. It is used to

extend the reach and robustness of long, lossy, crosstalk-impaired high-speed serial links while achieving

a bit error rate (BER) of 10-15 or less. Each channel of the DS250DF810 independently locks to serial

data rates in a continuous range from 20.6 Gbps to 25.8 Gbps or to any supported sub-rate (÷2 and ÷4),

including key data rates such as 10.3125 Gbps and 12.5 Gbps. Integrated physical AC coupling

capacitors (TX and RX) eliminate the need for external capacitors on the PCB. The DS250DF810 has a

single power supply and minimal need for external components. These features reduce PCB routing

complexity and BOM cost. The advanced equalization features of the DS250DF810 include a low-jitter 3-

tap transmit finite impulse response (FIR) filter, an adaptive continuous-time linear equalizer (CTLE), and

an adaptive decision feedback equalizer (DFE). This enables reach extension for lossy interconnect and

backplanes with multiple connectors and crosstalk. The integrated CDR function is ideal for front-port

optical module applications to reset the jitter budget and retime the high-speed serial data. The

DS250DF810 implements 2x2 cross-point on each channel pair, providing the host with both lane crossing

and fanout options.

The DS250DF810 can be configured via the default SMBus slave mode or with an external EEPROM. Up

to 16 devices can share a single EEPROM. A non-disruptive on-chip eye monitor and PRBS generator

and checker functions allow for in-system diagnostics. With this kit, users can quickly evaluate the

DS250DF810 retimer performance.

www.ti.com

2SNLU180C–August 2015–Revised September 2019

Submit Documentation Feedback

DS250DF810EVM User’s Guide

Contents

1 Hardware Description and Setup .......................................................................................... 3

2 Software Description ........................................................................................................ 4

3 Best Practices and Usage Tips........................................................................................... 21

4 Test Case Examples....................................................................................................... 22

5 Supplemental Documents................................................................................................. 23

6 EVM Cable Assemblies ................................................................................................... 24

List of Figures

1 DS250DF810EVM, Showing Necessary Connections for Power, Signal, and USB Communications........... 3

2 Download SigCon Architect from www.ti.com ........................................................................... 4

3 Sigcon Architect Start-Up Screen ......................................................................................... 5

4 Capture Illustrating the “Manage Devices” Pop-Up Window for Adding New Part Numbers to the

“Selection” Panel............................................................................................................. 6

5 Low-Level Page Capture Illustrating the Different Block Select Options............................................. 7

6 Low-Level Page Capture After Selecting Access to an Individual Register.......................................... 7

7 Eye Monitor Page for DS250DF810 Profile.............................................................................. 8

8 EEPROM Page for DS250DF810 Profile................................................................................. 9

9 High-Level Page, with Block Diagram Tab Selected .................................................................. 10

10 High-Level Page, with Device Status Tab Selected................................................................... 11

11 Rx EQ/DFE Tab............................................................................................................ 12

12 Cross-Point Tab, Default Mode Selected ............................................................................... 14

13 Cross-Point Tab, Fanout Mode Selected ............................................................................... 14

14 Cross-Point Tab, Lane Crossing Mode Selected ...................................................................... 15

15 CDR Tab, Standard Mode Selected..................................................................................... 16

16 CDR Tab, Manual Mode Selected....................................................................................... 17

17 TX FIR Tab.................................................................................................................. 18

18 PRBS Tab, PRBS Generator Configuration ............................................................................ 19

19 PRBS Tab, PRBS Checker Configuration .............................................................................. 20

20 SDD21 Loss Characteristic of Example Test Case.................................................................... 22

Trademarks

All trademarks are the property of their respective owners.

= Jumpers

Connect GND here

Connect 3.3 V here

Plug USB here

RX Channels

TX Channels

www.ti.com

Hardware Description and Setup

SNLU180C–August 2015–Revised September 2019

DS250DF810EVM User’s Guide

1 Hardware Description and Setup

The general procedure for setting up and testing with the DS250DF810 Evaluation Module

(DS250DF810EVM) hardware is as follows:

1. Check the EVM jumper settings to ensure they match Figure 1 below.

2. Connect the EVM to a PC using the provided USB cable.

3. Connect 3.3V power (2A max) as shown below. The EVM has an on-board 3.3V-to-2.5V regulator to

supply the Retimer with the required 2.5V.

Figure 1. DS250DF810EVM, Showing Necessary Connections for Power, Signal, and USB

Communications

4. Connect the EVM to the system under test.

The default EVM configuration has four differential RX inputs and four differential TX outputs accessible to

the user. Connect the RX and TX signals to the test channel using Huber+Suhner 1x8 MXP cable

assemblies (See Section 6 for ordering information).

NOTE: All TX and RX channels are AC coupled with physical 220 nF capacitors on the package of

the device, so external AC coupling capacitors are not needed when using this EVM.

Software Description

www.ti.com

4SNLU180C–August 2015–Revised September 2019

Submit Documentation Feedback

DS250DF810EVM User’s Guide

2 Software Description

2.1 Setup

The one-time procedure for installing the GUI software is as follows:

1. Download and install the TI SigCon Architect GUI. The steps for installing the software are as follows:

1. Go to www.ti.com/tool/sigconarchitect and download the latest version of SigCon Architect. At the

time this document was written, the latest version of SigCon Architect is 2.0.0.4.

Figure 2. Download SigCon Architect from www.ti.com

2. Extract the executable file (.EXE) from the downloaded file and run the executable.

3. Follow the installation wizard’s instructions to install SigCon Architect.

4. Download the DS250DF810 profile file from the TI SigCon Architect page.

5. Extract the executable file (.EXE) from the downloaded file and run the executable.

www.ti.com

Software Description

SNLU180C–August 2015–Revised September 2019

DS250DF810EVM User’s Guide

2. Run the SigCon Architect software.

1. Start the software by double-clicking its icon on the desktop.

2. On the “Selection” panel, the DS250DF810 should appear.

3. If DS250DF810 is not listed:

1. Go to “Device” tab and choose “Manage Devices”.

2. Click on “+” icon and then select the “DS250DF810” device model.

3. Fill in the “New Device Name, DS250DF810 is recommended.

4. Select the slave address as configured on EVM (typical setting is 0x30).

5. Click “OK”.

4. Navigate to the “Configuration” page of DS250DF810 via the “Selection” panel. Choose “Slave

Address” “0x30” from the drop down menu. Verify the “USB2ANY Details” specify “USB2ANY 0”,

and click “Apply”. Successful connection is indicated by the green “CONNECTED” indicator on the

bottom of the application.

Figure 3. Sigcon Architect Start-Up Screen

Software Description

www.ti.com

6SNLU180C–August 2015–Revised September 2019

Submit Documentation Feedback

DS250DF810EVM User’s Guide

Figure 4. Capture Illustrating the “Manage Devices” Pop-Up Window for Adding New Part Numbers to the

“Selection” Panel

3. Once connection is successfully established, users can read and write various settings to the device in

real-time, using the functional pages.

2.2 Functional Pages

2.2.1 Low-Level Page

The low-level page allows the user to read and write to all registers on the DS250DF810. To access it,

navigate to the “Low Level Page”, as shown below.

• The user may click “Read All” to load the data in each register from the device to the “Register Map."

• The user may access the Shared, Global or Channel registers via “Block Select.”

• To Read a register:

– Type the readable address in the “Current Address” text box or select a register from the Register

Map.

– Click “Read Register”. The data in this register will appear in the “Data” text box.

• To Write a register:

– Type the writeable address in the “Current Address” text box or select a register from the Register

Map.

– The user may either type the data value (in HEX) to write to this address in the “Data” text box, or

check/uncheck boxes as desired for individual bits within the register. Then click “Write Register.”

– If Broadcast is selected for channel register writes, the specified write will be performed to all

channels in the device.

www.ti.com

Software Description

SNLU180C–August 2015–Revised September 2019

DS250DF810EVM User’s Guide

Figure 5. Low-Level Page Capture Illustrating the Different Block Select Options

Figure 6. Low-Level Page Capture After Selecting Access to an Individual Register

Software Description

www.ti.com

8SNLU180C–August 2015–Revised September 2019

Submit Documentation Feedback

DS250DF810EVM User’s Guide

2.2.2 Eye Opening Monitor (EOM) Page

The Eye monitor page allows the user to visualize DS250DF810 eye plots, a means of assessing received

signal quality after equalization.

• Select the channel for eye plotting. Note that plots can only be generated for a given channel if “CDR

Locked” is indicated.

• The EOM_SEL_VRANGE pull-down allows the user to adjust the vertical scale for eye plots.

• The user may perform a “Single Capture” of eye monitor plot, or select “Continuous Capture” to

accumulate multiple plots over a period of time.

• The Horizontal Eye Opening (HEO) and Vertical Eye Opening (VEO) may be read on the Eye Monitor

page.

• If the user desires to do their own analysis or post-processing of the EOM data, the “Export Raw Data”

and “Export Density” buttons respectively generate an Excel spreadsheet containing the 63x63 eye

monitor values matrix.

Figure 7. Eye Monitor Page for DS250DF810 Profile

www.ti.com

Software Description

SNLU180C–August 2015–Revised September 2019

DS250DF810EVM User’s Guide

2.2.3 EEPROM Page

The SigCon Architect EEPROM page allows the user to either: create a DS250DF810 Hex file that is

programmable to an EEPROM, or configure a DS250DF810 device based on values from an existing

DS250DF810 Hex file.

Figure 8. EEPROM Page for DS250DF810 Profile

The user may choose to update the EEPROM page settings based on values read from the DS250DF810

device by clicking “Update Slot from Device”. To create the programmable hex file, click “Write to

EEPROM Hex”. Note that the evaluation module does not include an EEPROM, but an external EEPROM

can be used. SigCon Architect cannot directly program the EEPROM. The EEPROM Hex File can be

burned on the EEPROM via I2C communication (i.e. AARDVARK or equivalent interface adapter). The

EEPROM control settings are described in greater detail below.

• Common Channel: If this box is checked, all channels receive the same configuration. Different

devices can receive different configurations, but within one device, all channels will receive the same

configuration. If this box is unchecked, then the EEPROM will store the configuration as unique

channel configurations. Each of the four channels can receive a unique configuration.

• EEPROM>256:

– This setting must be enabled if there are more than 4 EEPROM slots.

– When this box is checked, the “EEPROM Size” drop down menu is automatically populated by 512

Bytes if previously populated by 256 Bytes.

– When this box is unchecked, the “EEPROM Size” drop down menu is automatically populated by

256 Bytes. Up to 4 EEPROM slots can be programmed.

• Enable CRC: If enabled, each device will have a CRC value specific to the base header, address map

header, and data. If disabled, the CRC is not computed.

• Slot Update Details: The number of slots refers to the total number of unique SMBus register settings

to load from the EEPROM. The user can choose to update all slots, or which slot # to update the

SigCon Architect EEPROM page from.

Software Description

www.ti.com

10 SNLU180C–August 2015–Revised September 2019

Submit Documentation Feedback

DS250DF810EVM User’s Guide

• EEPROM Size: The EEPROM size must be set to 256, 512, or 1024 bytes. A single external EEPROM

can be used by up to 16 DS250DF810 devices.

– The first 3 bytes of EEPROM data is the base header. The base header contains the CRC enabled,

address map header enabled, EEPROM<256 bytes, device count, and maximum EEPROM burst

size settings.

– If multiple devices are programmed, an address map header is needed for each device. The

address map header specifies the CRC value and the Device EEPROM Start Address.

– EEPROM Size ≤256 Bytes:

• EEPROM Size = 3 Bytes (Base Header) + # of devices * 8 Bytes/device (Address Header) + #

of slots * 66 Bytes/slot (Data)

– EEPROM Size > 256 Bytes:

• EEPROM Size = 3 Bytes (Base Header) + # of devices * 12 Bytes/device (Address Header) + #

of slots * 66 Bytes/slot (Data)

2.2.4 High-Level Page

2.2.4.1 Overview

The High-Level Page on the Selection Panel enables the user to easily configure and/or check the status

of the DS250DF810 high-speed data path functional blocks: Clock and data recovery (CDR), Receiver

equalization, Transmitter output driver, PRBS generator and checker, and cross-point. The figure below

shows the landing page after uses selects “High-Level Page on the Selection Panel. The first button

option is the “Block Diagram”, an illustrative page highlighting the DS250DF810’s functional stages. The

configuration features for the additional tabs within the High-Level Page are described further in the next

sub-sections.

Figure 9. High-Level Page, with Block Diagram Tab Selected

Este manual sirve para los siguientes modelos

Tabla de contenidos

Otros manuales de Hardware de computadora de Texas Instruments

Texas Instruments

Texas Instruments INA229 Manual de usuario

Texas Instruments

Texas Instruments PMP15034 Manual de usuario

Texas Instruments

Texas Instruments ADS125H02 Manual de usuario

Texas Instruments

Texas Instruments Sitara AM1335 Series Manual de usuario

Texas Instruments

Texas Instruments AM1802 Manual de usuario

Texas Instruments

Texas Instruments LM38020EVM Manual de usuario

Texas Instruments

Texas Instruments Chipcon Products CC2431 Manual de usuario

Texas Instruments

Texas Instruments TPS61196EVM-600 Manual de usuario

Texas Instruments

Texas Instruments TPS7A15 Manual de usuario

Texas Instruments

Texas Instruments TVP5154EVM Manual de usuario

Texas Instruments

Texas Instruments AM1808 Manual del producto

Texas Instruments

Texas Instruments TAS3002 Guía de instalación y uso

Texas Instruments

Texas Instruments bq20z60EVM-001 Manual de usuario

Texas Instruments

Texas Instruments MSP-EXP430F5438 Manual de usuario

Texas Instruments

Texas Instruments SimpleLink CC2640 Manual de usuario

Texas Instruments

Texas Instruments BoosterPack BOOSTXL-ADS7142-Q1 Manual de usuario

Texas Instruments

Texas Instruments UCC217 QDWEVM-054 Series Manual de usuario

Texas Instruments

Texas Instruments PGA450Q1EVM Manual de usuario

Texas Instruments

Texas Instruments TIDA-070005 Guía

Texas Instruments

Texas Instruments AM57 Series Manual de usuario

Texas Instruments

Texas Instruments AN-1646 Manual de usuario

Texas Instruments

Texas Instruments LM97937EVM R2 Manual de usuario

Texas Instruments

Texas Instruments TMS320C6201 Manual de usuario

Texas Instruments

Texas Instruments TMDSCNCD2800157 Manual técnico

Manuales populares de Hardware de computadora de otras marcas

EMC2

EMC2 VNX Series Manual del propietario

Panasonic

Panasonic DV0PM20105 Manual de usuario

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manual de usuario

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manual de usuario

Raidon

Raidon iT2300 Manual de usuario

National Instruments

National Instruments PXI-8186 Manual de usuario

Hauppauge

Hauppauge WinTV-HVR-2250 Manual de usuario

Kontron

Kontron CP6002 Manual de usuario

Manhattan

Manhattan 702843 Manual de usuario

Aphex

Aphex 230 Manual de usuario

AMD

AMD Phenom II Manual operacional

Intel

Intel NUC 12 Pro Manual de usuario

dbx

dbx Zone Pro 1260 Manual de usuario

Galaxy

Galaxy GHDX2-2430S-24F4D Manual de usuario

Intel

Intel AXXRMFBU4 Manual de usuario

Kontron

Kontron DIMM-PC/MD Manual de usuario

ST X-NUCLEO-SAFEA1B Instrucciones de funcionamiento

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manual de usuario