Teltonika FM5500 Manual de usuario
1
FM5500 Sample User Guide for Recommended
Configuration
1About the document
This document contains information required for fast testing of the FM5500 device
1.1
Getting started with FM5500 device
This paragraph contains the information needed to successfully launch and use the FM5500
device. The steps below should be followed carefully to completely test the FM5500.
1.2
SIM card insert scheme
2
Pic. 1. Illustration of how to insert the SIM card
1.3
Power source connection
(-) EXT. BAT
10
20
(+) EXT. BAT
OUT 2
9
19
OUT 1
OUT 3
8
18
OUT 4
AIN 2
7
17
AIN 1
AIN 4
6
16
AIN 3
DIN 2
5
15
DIN 1
DIN 4
4
14
DIN 3
1W. PWR
3
13
1W. data
CAN L
2
12
CAN H
(-)GND
1
11
(+)VCC (10…30) V DC
Pic. 2. Standard FM5500 2x10 socket pinout
The external 10...30 V DC (12 W Max) power supply must be used to power up the device.
Connect power supply to 1 pin and 11 pin as shown above.
3
1.4
Placement of GPS antenna
GPS antenna must be placed so its state is as horizontal as possible (if antenna is leaning more
than 30 degrees, it is considered incorrect mounting).
GPS antenna cable cannot be bent more than 80 degrees.
GPS antenna must be placed sticker facing down
Pic. 3. GPS antenna correct mounting
It is recommended to place GPS antenna as close to the window as possible.
NOTE, that most of modern office windows are equipped with filters that could block GPS signal so
for best GPS signal quality we recommend to put GPS antenna outside (on windowsill, some plate
etc.).
1.5
Installing FM5500 drivers
Software requirements
• Operating system 32-bit and 64-bit: Windows XP with SP3 or later, Windows Vista, Windows 7.
• MS .NET Framework V3.5 or later (http://www.microsoft.com or
http://avl1.teltonika.lt/downloads/tavl/Framework/dotnetfx35setupSP1.zip).
Drivers
Please download Virtual COM Port drivers from Teltonika website:
http://avl1.teltonika.lt/downloads/FM11/vcpdriver_v1.3.1_setup.zip
Installing drivers
Extract and run VCPDriver_V1.3.1_Setup.exe. This driver is used to detect FM5500 device connected
to the computer. Click 'Next' in driver installation window (pictures 5-7):
4
Pic. 4. Driver installation window
This will launch device driver installation wizard. In the following window click „Next‟ button again:
Pic. 5. Driver installation window
Setup will continue installing drivers and will display a window about successful process in the end.
Click 'Finish' to complete setup:
Pic. 6. Driver installation window
You have now installed drivers for FM5500 device successfully.
5
1.6
Loading the Configuration into the FM5500 Device
FM5500 Configurator must be used to configure the FM5500 device. Configurator can be
downloaded from: http://avl1.teltonika.lt/downloads/FM55/ or contact our sales manager to get
latest configurator version. The only data client is required to enter to configuration is APN data,
domain and target server port.
Pic. 7. Configuration toolbar view
1.6.1 APN configuration
In order to make FM5500 device to be able to connect to local GPRS network (and send AVL
data) the following APN data (provided by local GSM services provider) must be entered into FM5500
configuration:
Access Point Name (APN) with authentication type CHAP or PAP (if required);
APN login;
APN password;
If you are not sure what APN settings should be, please contact your GSM operator.
1.6.2 Domain and Port configuration
In the domain field you have to enter your server IP address, where to send FM AVL data.
6
In Target Server Port field you have to enter your server Port number. In recommended
configuration mode transfer protocol is set to TCP. But also you can set UDP transfer protocol in
advanced configuration.
1.6.3 Saving the Configuration into the FM5500 Device
Follow these steps:
1. Press connect in configurators navigation bar ( make sure that your FM5500 is connected to
PC and power source).
Picture 8. Connecting FM5500 to configurator
2. When device is connected to configurator you can save your configuration by clicking Save.
Picture 9. Saving configuration to FM5500 device
1.6.4 Recommended Configuration
Recommended configuration is based on fast periodic AVL data acquisition mainly according
to the change of the object‟s geographic angle (Min.Angle = 10 degrees). According to this
configuration the FM5500 device will generate AVL record every time the object‟s angle is changed
more than 10 degrees. Such AVL data acquisition is rational in cases the object mostly moves in the
city. Min.Distance = 100 meters, so the additional AVL record will be generated after driving more
than 100 meters in the straight line. If the object with FM5500 device is not moving, the AVL data
records are generated periodically every 300 seconds (Min.period = 300 s).
AVL data is sent via GPRS to the server as soon as the AVL data record is generated (Min.
saved records = 1; Send period = 10 s). According to this configuration one AVL data record,
containing information about the GPS position and Input/Output (I/O) parameters is sent to the
server at least every 300 seconds.
Following I/O elements‟ vales are monitored in every AVL data record:
DIN1 (as ignition) {values: 0 –Off; 1 –On};
Power voltage {values: from 10 V to 30 V, according to the power source).
Odometer {values: what is driven distance between two coordinate‟s points}
7
Additional AVL data records called “events” are generated on following parameter value
changes:
If power voltage value falls less than 11 V;
Ignition is turned ON/OFF (DIN1=1 or DIN1=0).
1.6.5 What is the purpose of testing FM5500 in this scenario?
The main propose of this testing scenario is for the user to see the highly detailed track (as in
the sample screenshot below) of his driven track in the city. The user will be able to see his vehicles
current position as well as the position in any selected time in the past. The user will be able to see the
time and points in the map in which the ignition has been turned ON/OFF, power voltage has become
less then 11 V (car battery needs to be recharged).
Pic. 10. Track of the FM5500 working in "City scenario"
The track showed in the screenshot above contains the information of 3 days driving of real
vehicle in the city of Vilnius, Lithuania. Using the service of local GSM service provider “Bite GSM”
1 MB of data has been transmitted through the GPRS to generate such track.
NOTE, that GPRS traffic differs from the GPRS coverage at the area and the GSM service
provider‟s data averaging policy, so the GPRS traffic can be higher than the described in the
example above.
Otros manuales para FM5500
1
Tabla de contenidos
Otros manuales de GPS de Teltonika
Teltonika
Teltonika FMB110 Guía de instalación
Teltonika
Teltonika FMB122 Guía de instalación
Teltonika
Teltonika TMT250 Manual de usuario
Teltonika
Teltonika FMB001 Guía de instalación
Teltonika
Teltonika FMB001 Manual de usuario
Teltonika
Teltonika FMB002 Manual de usuario
Teltonika
Teltonika FMC800 Guía de instalación
Teltonika
Teltonika FMC920 Manual de usuario
Teltonika
Teltonika Telematics FMM150 Guía de instalación
Teltonika
Teltonika FMB140 Manual de usuario
Teltonika
Teltonika FMC00A Guía de instalación
Teltonika
Teltonika FMB110 Manual de usuario
Teltonika
Teltonika FMB003 Manual de usuario
Teltonika
Teltonika TMT250 Manual de usuario
Teltonika
Teltonika FMC800 Manual de usuario
Teltonika
Teltonika Telematics FMM650 Guía de instalación
Teltonika
Teltonika FMB64 Manual de usuario
Teltonika
Teltonika FMM800 Manual de usuario
Teltonika
Teltonika FMB225 Guía de instalación
Teltonika
Teltonika GH5200 Manual de usuario
