Teltonika MSP500 Manual de usuario

https://wiki.teltonika-gps.com/view/MSP500_First_Start

MSP500 First Start

Main Page > Advanced Trackers > MSP500 > MSP500 First Start

MSP500 is a special tracking terminal with GNSS/GSM/Bluetooth connectivity, internal

GNSS/GSM antennas, RS232 interface for ESC/POS printer support and internal Ni-Mh

battery. Moreover, device contains integrated buzzer and relay for a speed limiting

functionality based on a fuel pump power supply switching.

Contents

1 Know your device

2 How to insert Micro-SIM card and connect the battery

3 Socket pinout

4 Wiring scheme

4.1 PC Connection (Windows)

4.2 How to install USB drivers (Windows)

4.3 Configuration (Windows)

4.4 Quick SMS configuration

5 Safety information

Know your device

How to insert Micro-SIM card and connect the battery

Gently remove MSP500 cover using plastic pry tool from both sides.1.

Insert Micro-SIM card as shown with PIN request disabled or read Security info how to2.

enter it later in Teltonika Configurator. Make sure that Micro-SIM card cut-off corner is

pointing forward to slot.

Connect battery as shown to device. Position the battery in place where it does not obstruct3.

other components.

After configuration, see “PC Connection (Windows)”, attach device cover back.4.

Device is ready to be installed.

Micro-SIM card insertion/removal must be performed when device is powered off –

external voltage and internal battery disconnected. Otherwise Micro-SIM card might be

damaged or device will not detect it.

Socket pinout

NUMBER PIN NAME DESCRIPTION

1VCC (10-32)V

DC (+)

Power supply (+10-32 V

DC).

2 RS232 GND RS232 Ground pin.

3 RS232-TX Output for data transmit

through RS232.

4 USB DATA + Differential serial data +

5 USB DATA- Differential serial data -

6GND (-) Ground.

7 AIN1 Analog input, channel 1.

Input range: 0-30 V DC.

8 RS232-RX Input for data receive

through RS232

9 USB GND Ground PIN for USB

10 USB +5V Ground PIN for USB

Wiring scheme

For the more detailed MSP500 device wiring, see the scheme below.

PC Connection (Windows)

Power-up MSP500 with DC voltage 10-30 V power supply using supplied power cable.1.

LED’s should start blinking, see “MSP500 LED status”.

Connect device to computer using USB B-Type cable connection:2.

Using USB B-Type cable

You will need to install USB drivers, see "How to install USB drivers

(Windows)"

You are now ready to use the device on your computer.3.

How to install USB drivers (Windows)

Please download COM port drivers from Teltonika here.1.

Extract and run TeltonikaCOMDriver.exe.2.

Click Next in driver installation window.3.

In the following window click Install button.4.

Setup will continue installing the driver and eventually the confirmation window will appear.5.

Click Finish to complete the setup.

Configuration (Windows)

At first MSP500 device will have default factory settings set. These settings should be changed

according to the user's needs.

Main configuration can be performed via Teltonika Configurator software. Get the latest MSP500

Configurator version from here. Configurator operates on Microsoft Windows OS and uses

prerequisite MS .NET Framework. Make sure you have the correct version installed.

MS .NET requirements

Operating

system

MS .NET

Framework

version

Version Link

• Windows

Vista

• Windows

8.1

• Windows

MS .NET

Framework

4.6.2

32 and

64 bit

www.microsoft.com

Downloaded Configurator will be in compressed archive. Extract it and launch Configurator.exe.

After launch software language can be changed by clicking in the right bottom corner:

Configuration process begins by pressing on connected device:

After connection to Configurator Status window will be displayed:

Various Status window tabs display information about GNSS, GSM, I/O, Maintenance and etc.

MSP500 has one user editable profile, which can be loaded and saved to the device. After any

modification of configuration the changes need to be saved to device using Save to device button.

Main buttons offer following functionality:

Load from device – loads configuration from device.1.

Save to device – saves configuration to device.2.

Load from file – loads configuration from file.3.

Save to file – saves configuration to file.4.

Update firmware – updates firmware on device.5.

Read records – read records from device.6.

Reboot device – restarts device.7.

Reset configuration – sets device configuration to default.8.

Most important configurator section is GPRS – where all your server and GPRS settings can be

configured and Data Acquisition – where data acquiring parameters can be configured. More

details about MSP500 configuration using Configurator can be found here.

Quick SMS configuration

Default configuration has optimal parameters present to ensure best performance of track quality

and data usage.

Quickly set up your device by sending this SMS command to it:

" setparam

2001:APN;2002:APN_username;2003:APN_password;2004:Domain;2005:Port;2006:0"

GPRS settings:

2001 – APN

2002 – APN username (if there are no APN username, empty field should be left)

2003 – APN password (if there are no APN password, empty field should be left)

Server settings:

2004 – Domain

2005 – Port

2006 – Data sending protocol (0 – TCP, 1 – UDP)

Note: Before SMS text, two space symbols should be inserted.

Default configuration settings

Movement and ignition detection:

Vehicle movement will be detected

by accelerometer

Ignition will be detected by

vehicle power voltage

between 13,2 – 30 V

Device makes a record On Moving if one of these events happen:

300 seconds passes Vehicle turns 10° degrees

Vehicle drives 100 meters

Speed difference between

last coordinate and current

position is greater than 10

km/h

Device makes a record On Stop if:

1 hour passes while vehicle is

stationary and ignition is off

Records sending to server:

If device has made a record it is

sent to the server every 120

seconds

After successful SMS configuration, MSP500 device will synchronize time and update records to

configured server. Time intervals and default I/O elements can be changed by using Teltonika

Configurator or SMS parameters.

Safety information

This message contains information on how to operate MSP500 safely. By following these

requirements and recommendations, you will avoid dangerous situations. You must read these

instructions carefully and follow them strictly before operating the device!

The device uses SELV limited power source. The nominal voltage is +12 V DC. The allowed

voltage range is +10..+30V DC.

To avoid mechanical damage, it is advised to transport the device in an impact-proof package.

Before usage, the device should be placed so that its LED indicators are visible. They show the

status of device operation.

Before unmounting the device from the vehicle, ignition MUST be OFF.

===Precautions===

Do not disassemble the device. If the device is damaged, the power supply cables are

not isolated or the isolation is damaged, DO NOT touch the device before unplugging

the power supply.

All wireless data transferring devices produce interference that may affect other

devices which are placed nearby.

Please consult representatives of your vehicle model regarding OBD II location on your

vehicle. In case you are not sure about proper connection, please consult qualified

personnel.

The programming must be performed using a PC with autonomic power supply.

The device is susceptible to water and humidity.

Installation and/or handling during a lightning storm is prohibited.

Teltonika is not responsible for any harm caused by wrong cables used for connection

between PC and MSP500.

WARNING! Do not use MSP500 device if it distracts driver or causes inconvenience due

to OBD II placement. Device must not interfere with driver.

Otros manuales para MSP500

Tabla de contenidos

Otros manuales de GPS de Teltonika

Teltonika

Teltonika FM640 Manual de usuario

Teltonika

Teltonika FM2 Manual de usuario

Teltonika

Teltonika GH5200 Guía de instalación y uso

Teltonika

Teltonika GH3000 Instrucciones de montaje

Teltonika

Teltonika TAT140 Guía de instalación

Teltonika

Teltonika FMB202 Guía de instalación

Teltonika

Teltonika FMB110 Guía de instalación

Teltonika

Teltonika LV-CAN100 Manual de usuario

Teltonika

Teltonika FMA202 Manual de usuario

Teltonika

Teltonika GH5200 Manual de usuario

Teltonika

Teltonika FMB640 Manual de usuario

Teltonika

Teltonika FM2100 Manual de usuario

Teltonika

Teltonika FMC920 Guía de instalación

Teltonika

Teltonika TAT100 Manual de usuario

Teltonika

Teltonika FMB110 Manual de usuario

Teltonika

Teltonika FMB225 Manual de usuario

Teltonika

Teltonika FMC230 Guía de instalación

Teltonika

Teltonika FM1200 Manual de usuario

Teltonika

Teltonika FMB209 Guía de instalación

Teltonika

Teltonika FM2200 Manual de usuario

Teltonika

Teltonika FMB001 Manual de usuario

Teltonika

Teltonika Telematics FMM150 Guía de instalación

Teltonika

Teltonika FMB930 Guía de instalación

Teltonika

Teltonika FMB204 Guía de instalación

Manuales populares de GPS de otras marcas

Raven

Raven Cruizer II Manual

Hama

Hama 53118 Manual de usuario

Garmin

Garmin SOUNDER 125 Manual de usuario

Garmin

Garmin DEZL 580 Manual de usuario

Jigabot

Jigabot EX Manual de usuario

Pointer

Pointer Cellocator CelloTrack XT LTE Guía de instalación

Queclink

Queclink GV55LITE Manual de usuario

Voxson

Voxson Voxtrack GPS500 Manual de instrucciones

Garmin

Garmin ECHOMAP PLUS Manual de usuario

Starcom Systems

Starcom Systems Kylos Compact Manual de usuario

Garmin

Garmin 15 H Series Manual de usuario

Cobra

Cobra Marine MC 600Ci Manual de usuario

Cellocator

Cellocator CelloTrack T Manual de usuario

Enfora

Enfora Mini-MT GSM2228UG001 Manual de usuario

Magellan

Magellan eXplorist 100 Manual de usuario

LTE

LTE G50B Manual de usuario

Garmin

Garmin DEZL OTR500 Manual de usuario

SkyGolf

SkyGolf SkyCaddie SG1 Manual de usuario