Tektronix TM 5006 Manual de usuario

Tektronix, Inc.

P.O. Box 500

Beaverton, Oregon

070-2950-00

Product Group 76

IbktfDnix-

COMMnTH3TO EXCELLENCE

TM 5006

POWER MODULE

INSTRUCTION MANUAL

97077 Serial Number

First Printing JAN 1981

Revised OCT 1987

Contents ol this publicsiion msy not be reproduced In sny

form without the written permission of Tektronix. Inc.

Products of Tektronix, Irtc. erKi its subsidisries ere covered

by U.S. snd foreign patents and/or pending patents.

TEKTRONIX. TEK. SCOPE'MOBILE and ^are reg-

istered trademarks of Tektronix. Inc.

Printed in U.S.A. Specification and price change privileges

are reserved.

INSTRUMENT SERIAL NUMBERS

Each instrument has aserial number on apanel insert, tag,

or stamped on the chassis. The first number or letter

designates the country of manufacture. The last five digits

of the serial number are assigned sequentially and are

unique to each instrument. Those manufactured in the

United States have six unique digits. The country of

manufacture is identified as follows;

BOOOOOO Tektronix, Inc., Beaverton. Oregon. USA

100000 Tektronix Guernsey, Ltd., Channel Islands

200000 Tektronix United Kingdtxn, Ltd., London

300000 Sony/Tektronix. Japan

700000 Tektronix Holland, NV. Heerenveen.

The Netherlands

TM5006

TABLE OF CONTENTS

Page

UST OF ILLUSTRATIONS rv

LIST OF TABLES v

OPERATORS SAFETY SUMMARY vi

SERVICE SAFETY SUMMARY vH

SMtIon 1SPECIFICATION

Instrument Description 1*1

Performance Conditions 1-1

Electrical Characteristics 1«1

Environmental Characteristics 1*4

Physical Characteristics 1-5

Section 2OPERATING INSTRUCTIONS

Introduction 2-1

Power Source Requirements 2-1

Fuse Replacement 2-1

Cabling 2-1

Page

Table Top Use 2-1

Rackmounting Instructions 2-1

Plug-in Installation and Removal ... 2-3

Family Compatibility 2-3

Customizing the Interface 2-3

Rear Panel 2-6

Option 02 2-6

Repackaging Information 2-6

ClMein2 INSTRUCTIONS D'lrriLISATION

Introduction 2-1

Source d'alimentation 2-1

RempJacament d'un fusible 2-1

Cdblage 2-1

UtHisetion sur une table de travail 2-1

Montage an bale 2-1

Installation et retrait des tirolrs 2-3

Compatibility avec les autres families 2-3

Personnalisatlon de I'interface 2-6

Panneau arhyre 2-6

Option 02 2-6

Irrstructions de reemballage 2-6

REV JAN 1983 I

TM 5006

TABLE OF CONTENTS (CONT)

Page

Section 3THEORY OF OPERATION

Introduction

Line Selector 60 Hz

Transformer

Rectifiers and Fillers

20 kHz Output Stage

Control Logic and Drivers ...

Output Regulator

Overvoltage and Overcurrent

Detectors

Control Circuit Reguiator ...

Main Interface

3-1

3-3

3-4

3-5

Section 4CALIBRATION

Performance Check Procedure .... 4-1

Introduction 4-1

Test Equipment Required 4-1

Test Loads for the Performance

Check Procedure 4-1

Performance Check Summary

Sheet 4-2

Internal Adjustment Procedure .... 4-5

Introduction 4-5

Services Available 4-5

Test Equipment Required 4-5

Adjustment Access 4-5

Power Limit Adjustment 4-5

Sections MAINTENANCE

Line Voltage Selection 5-1

Static Sensitive Components .... 5-1

Cleaning 5-2

Obtaining Replacement Parts ... 5-2

Soldering Techniques 5-3

Semiconductors 5-3

Multipin Connectors 5-3

Instrument Disassembly 5-3

Circuit Troubleshooting 5-5

Rear Interface Information 5-10

PWR Indicator 5-10

Pin Assignments 5-10

ii REV JAN 1983

TM S006

TABLE OF CONTENTS (cont)

P«9«

SMtIonI OPTIONS

introduction 6-1

Option 02 6-1

Syttom Dotign Diroctlon* 6-1

Wiro Um 6-1

SteSenr REPLACEABLE ELECTRICAL PARTS

SwHoni DiAQRAMS AND CIRCUIT BOARD

ILLUSTRATIONS

Component Reference Cherts

Schematic Oisgrams

Secflon 9REPLACEABLE MECHANICAL

PARTS

Rg. 1Exploded View

Accessories

CHANGE INFORMATION

REV JAN 1983 iii

TM 5006

LIST OF ILLUSTRATIONS

Rg. No. Page

TM 5006 Power Module vii)

2-1 TM 5006 rear panel 2-2 .

2-2 TM 5006 front view 2-3

2-3 TM 5006 bottom view 2-4

2-4 TM 5006, Option 10 overall dimenelona 2-5

2-5 Rack latch hole 2*6

2-6 Dimensions artd positioning of TM 5006.

Option 10, in standard rack 2-7

2-7 Rackmount slide detail. If the rack has

tapped holes, the bar nuts are not

required 2-6

2-8 Rackmountir>g slide details 2-8

2-9 Removing andinstalling TM 5006, Option

10. in rack slides 2-9

2-10 Plug-in installation and removal 2-10

11 Keying assignments for family functions.

One of the many possible sequence

combinations 2-10

1Variouswaveformsandtimerelatiortships

for power on, off. fault, and low line ... 3-2

2Inputlineconnectlonsfor 110 Vand220 V

operation 3-3

1Possible loads for use in performance

check procedure. See text 4-1

4-2 Testsetupforperformancecheckstepsl,

2ar>d 3and location of connections for

adjustment step 14-4

4-3 Loads for use in internal

adjustment procedure 4-5

4-4 Adjustment location illustration 44

5Location of voltage buses 44

1Line cord options for the TM 5006 .... 5-1

5-2 Line voltage jumper positiom 5-2

5-3 Orientation and disassembly of multipin

connectors 5-3

Rg. No. Page

5-4 Outer panel removal 5-4

^5 Guide rail and air baffle removal 5-4

5-6 Removal Of interface circuit board

support 5-5

5-7 Main interface circuit board removal ..5-6

5-8 Rear par>el removal 5-6

5-9 Location of screws holding the dc power

supply circuit board to the mainframe

chassis 5-7

5-10 Attaching screws on bottom of

mainframe 5-7

5-11 Unsolder these wires to remove

heat sink 5-8

5-12 Series pass transistor locations. The high

power compartment series pass

transistors 0600 and Q610are onthe right

side of the heat sink. Q600 is the upper

transistor 5-9

5-13 Screws holding heat sink to circuit

board 5-9

5-14 Transformer assembly attaching

screws 5-9

5-15 PWR signal timing diagram 5-10

5-16 Rear interface connector assignments .5-11

^17 Rear panel QPIBconnectorJItlOviawed

from rear of power module (IEEE

Standard No. 488) 5-12

8-1 Dc power supply board (All)

8-2 Dc power supply regulator waveforms

8-3 Mein interlace board (A10)

8-4 QPIB interconnect board (A16 back side)

IV REV NOV 1964

TM 5006

LIST OF TABLES

T«Mt rto. P«fl«

1-1 B«ctrtcal Characteristics 1-1

1-2 Environmental Characteristics 1-4

1-3 Physical Characteristics 1-5

1Suggested Test Equipment 4-3

1RelativeSusceptIbilitytoStaticDischarge

Damage 5-2

1Partial A11 Component Reference Chart

6-2 Partial A11 Component Reference Chart

6-3 A10 Component Reference Chart

REV JAN 1983 V

TM5006

OPERATORS SAFETY SUMMARY

The general safety information in this part of the summary

is for both operating and servicing personnel. Specific

warnings and cautions wili be found throughout the

manusi where they apply, but may not appear in this

summary.

Terms In This INanual

CAUTiON statements identify conditions or practices that

could result In damageto the equipment or other property.

WARNING statements Identify conditior« or practices

that could result In personal Injury or loss of life.

Terms As Marked on Equipment

CAUTION indicates apersonal injury hazard not im-

mediately accessible mone reads the marking, or a

hazard to property including the equipmerrt itself.

DANGER indicates apersonal injury hazard immediately

accessible as one reads the marking.

and ground. Aprotectivegroundconnectionby wayof the

grounding conductor in the power cord Is essential for

safe operation.

Grounding the Product

This product is grounded through the grounding conduc-

tor of the power cord. To avoid electrical shock, plug the

power cord Into aproperly «*ired receptacle before

connecting to the product input or output terminals. A

protective ground connection by way of the grounding

conductor In the poww cord Is essential for safe opera-

tion.

Danger Arising From Loss of Ground

Upon loss of the protective-ground connection, all

accessible conductive parts (ir>cluding knobs and cort-

trols that may appear to be insulating) can render an

electric shock.

Symbols In TNs Manual

AThis symbol indicates where applicable

cautionary or other information is to be

found.

Use the Proper Fuse

To avoid fire hazard, use only the fuse of correct type,

voltage rating and current rating as speciried in the p^s

list for your product.

Symbols As Marked on Equipment

DANGER —High voltage.

Protective ground (earth) terminal.

ATTENTION —refer to manual.

Refer fuse replacemern to quslified service personnel.

Do Not Operate in Explosive Atmospheres

To avoid explosion, do not opsrMs this product in an

explosive atmosphere unless it has been specifically

certified for such operstion.

Power Source

This product is intended to operate from apower source

that will not apply more than 250 volts rms between the

supply conductors or between either supply conductor

Do Not Operate Without Covers

To avoid personal Injury, do not remove the product

covers or panels. Do not operatsthe product without the

covers and panels properly installed.

VI ADO JAN 1983

TM 5006

SERVICE SAFETY SUMMARY

FOR QUALIFIED SERVICE PERSONNEL ONLY

Refer also to the preceding Operetore Safety Summary.

Do Not Servic* Alone

Do not perform Internal service or adjustment of tNs

product unless another person capable of rendering first

aid and resuscitation is present

Use Care When Servicing With Power On

Dangerous voltages exist at several points In this product

To avoid personal injury, do not touch exposed connec-

tions and components while power is on.

Disconnect power before removing protective panels,

soldering, or replacing components.

Power Source

This product is intended to operate from apower source

that will not apply nwe than 250 volts rms between the

supply conductors or between either supply conductor

and ground. Aprotective ground connection by way of the

grounding conductor in the power cord Is essential for

safe operation.

REV JAN 1983 vil

Otros manuales para TM 5006

Tabla de contenidos

Otros manuales de Unidad de control de Tektronix

Tektronix

Tektronix VX4730 Manual de usuario

Tektronix

Tektronix TDS3TMT Manual de usuario

Tektronix

Tektronix ECO8000 Series Manual de usuario

Tektronix

Tektronix TM 5003 Manual de usuario

Tektronix

Tektronix TM 501 Manual de usuario

Tektronix

Tektronix TM 501 Manual de usuario

Tektronix

Tektronix 3B5 Manual de usuario

Tektronix

Tektronix 7B15 Manual de usuario

Tektronix

Tektronix 7S11 Manual de usuario

Tektronix

Tektronix TDS3FFT Manual de usuario

Tektronix

Tektronix VX4521 Manual de usuario

Tektronix

Tektronix ECO170A Manual de usuario

Tektronix

Tektronix TM 506 Manual de usuario

Tektronix

Tektronix KEITHLEY 4225-RPM Manual de usuario

Tektronix

Tektronix TDS200 Series Manual de usuario

Tektronix

Tektronix 80E01 Manual de usuario

Tektronix

Tektronix TM 502A Manual de usuario

Tektronix

Tektronix 7B70 Manual de usuario

Tektronix

Tektronix VX4342 Manual de usuario

Tektronix

Tektronix TDS3SDI Manual de uso y cuidado

Tektronix

Tektronix DPO3PWR Manual de usuario

Tektronix

Tektronix VX4790A Manual de usuario

Tektronix

Tektronix TM 5006 Manual de usuario

Tektronix

Tektronix VX4237 Manual de usuario

Manuales populares de Unidad de control de otras marcas

Festo

Festo Compact Performance CP-FB6-E Manual de lista de piezas

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manual de usuario

JS Automation

JS Automation MPC3034A Manual de usuario

JAUDT

JAUDT SW GII 6406 Series Guía rápida

Spektrum

Spektrum Air Module System Manual de usuario

BOC Edwards

BOC Edwards Q Series Manual de usuario

KHADAS

KHADAS BT Magic Manual de usuario

Etherma

Etherma eNEXHO-IL Manual de usuario

PMFoundations

PMFoundations Attenuverter Manual de usuario

GEA

GEA VARIVENT Manual de usuario

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manual de usuario

Altronix

Altronix LINQ8PD Instrucciones de montaje

Eaton

Eaton Powerware Series Manual de usuario

WAGO

WAGO 750-407/040-000 Manual de usuario

Sony

Sony CCU-590 Manual de usuario

Graco

Graco 25D614 Manual de usuario

Task Force Tips

Task Force Tips YE-RF-900 Manual de programación

Shini

Shini SPV-U Series Manual de usuario