Stratasys ProBleacher Manual de usuario
DOC-01010 Rev. C
ProBleacher
Photobleaching Chamber
Stratasys ProBleacher Product Guide
Stratasys ProBleacher Product Guide
Page 2
© Copyright 2021 Stratasys. All rights reserved.
Copyright
© Copyright 2021 Stratasys. All rights reserved.
This documentation contains proprietary information of Stratasys Ltd. This information is
supplied solely to assist authorized users of this cleaning system. No part of this document
may be used for other purposes, and it may not be disclosed to other parties.
The specifications on which this document is based are subject to change without notice.
No part of this book may be reproduced in any form or by any means, nor stored in a database
or retrieval system, without prior permission in writing from Stratasys Ltd.
If this document is distributed as a PDF file, you may print it for internal use.
DOC-01010 Rev. C
Trademark
Stratasys, Stratasys logo, Objet, PolyJet, and ProBleacher are trademarks of Stratasys Ltd.
and/or its subsidiaries or affiliates and may be registered in certain jurisdictions.
All names of product names and trademarks are the property of their respective owners.
Liability
Stratasys shall not be liable for errors contained herein or for incidental or consequential
damages in connection with the furnishing, performance, or use of this material. Stratasys
makes no warranty of any kind with regard to this material, including, but not limited to, the
implied warranties of merchantability and fitness for a particular purpose. It is the responsibility
of the system owner/material buyer to determine that Stratasys material is safe, lawful, and
technically suitable for the intended application as well as identify the proper disposal (or
recycling) method consistent with local environmental regulations. Except as provided in
Stratasys' standard conditions of sale, Stratasys shall not be responsible for any loss resulting
from any use of its products described herein.
Disclaimer
Customer acknowledges the contents of this document and that Stratasys parts, materials, and
supplies are subject to its standard terms and conditions, available on
https://www.stratasys.com/legal/terms-and-conditions-of-sale, which are incorporated herein
by reference.
Stratasys Ltd.
www.stratasys.com
Comments: [email protected]
Stratasys ProBleacher Product Guide Contents
Page 3
© Copyright 2021 Stratasys. All rights reserved.
Contents
Contents........................................................................................ 3
Overview ....................................................................................... 4
Warranty........................................................................................ 4
Compliance ................................................................................... 4
Safety ............................................................................................ 4
Specifications ................................................................................ 5
Unpacking ..................................................................................... 5
Setup............................................................................................. 6
Operation ...................................................................................... 6
Operation Modes .................................................................................................. 6
Run Screen ........................................................................................................... 8
Care and Maintenance.................................................................. 8
Spare Parts ................................................................................... 9
Storage and Transportation........................................................... 9
Stratasys ProBleacher Product Guide Overview
Page 4
© Copyright 2021 Stratasys. All rights reserved.
Overview
ProBleacher is a photobleaching chamber. It uses LED light to provide an ideal environment
suitable for photobleaching 3D PolyJet printed models.
Warranty
ProBleacher has a limited one-year warranty (or greater when required by local law) that
covers everything except the LED lamps, which are considered consumable items. Details on
the warranty can be found in the legal section of the Stratasys website:
https://www.stratasys.com/legal/system-warranty-period
https://www.stratasys.com/legal/terms-and-conditions-of-sale
Compliance
This product is CE and FCC compliant.
Safety
Read these important safety guidelines before using this product.
1. This product is intended for photobleaching 3D printed models. Do not use this product for
any other purpose as the safety of the product cannot be ensured.
2. Do not put flammable liquids in the chamber. Allow any solvents on the printed models to
completely evaporate before placing them in the chamber.
Flammable fluids in the chamber create a risk of fire and/or explosion.
3. Do not place items on or around this product to maintain unblocked airflow. Keep
flammable liquids away from this product. Do not put liquids on top of the product, as a spill
could create a risk of electric shock.
4. Do not look at the lamps without appropriate eye protection. This product is equipped with
a safety interlock that turns off the lamps when the door is opened.
5. Should this product malfunction in any way, immediately unplug it and contact your regional
service provider. Do not continue to operate a malfunctioning unit, as damage or even
injury may occur.
6. If you have any questions about the setup, use, or care of this product, please contact your
regional service provider.
Stratasys ProBleacher Product Guide Specifications
Page 5
© Copyright 2021 Stratasys. All rights reserved.
Specifications
Unpacking
1. Open the top flaps of the outer box.
2. Remove the foam corner protectors, and keep them for future use.
3. Remove the power cord from the box.
4. Remove the inner box.
5. Open the inner box top flaps. There is an orange Important insert inside the inner box.
Model 115V 230V
Power Input 110-120V 220-240V
Frequency 50-60 Hz
Ambient Temperature 10-30⁰C / 50-86⁰F
Relative Humidity 30-70% (non-condensing)
LED Output 9 Watts
LED Wavelength 450-560 nm
Unit Size 30.5 x 30.5 x 26 cm / 12 x 12 x 10.25 in.
Chamber Size 30.5 x 30.5 x 16 cm / 12 x 12 x 6.25 in.
Unit Weight 10 kg / 22 lbs
Shipping Size 41 x 41 x 36 cm / 16 x 16 x 14 in.
Shipping Weight 11.4 kg / 25 lbs
• Open the packaging carefully and store it for future use. Original packaging is
required should this product need warranty repair or replacement.
• This product is shipped in two boxes, a box within a box, to ensure it arrives
undamaged. It is recommended to unpack with 2 people.
Verify that the plug is suitable for your location. If not, purchase a cable locally.
Important:
This insert contains important safety information and you must read it thoroughly prior
to using this product.
Stratasys ProBleacher Product Guide Setup
Page 6
© Copyright 2021 Stratasys. All rights reserved.
6. Remove, read, and keep the Important insert for reference.
7. Remove the product from the inner box.
8. Remove the product from the protective bag. Hold the door to prevent it from opening while
removing the product from the box.
9. Place the product on a stable work surface.
10. Return packaging materials to the outer box and store them for future use, if necessary.
Setup
1. Verify that the power switch is in the off (0) position.
2. Insert the power cord into the power inlet at the back of the unit.
3. Plug the power cord into a power outlet.
Operation
1. Switch on (I) the power switch on the back panel. The power switch has a red light when
on, and the display screen turns on.
2. Open the front door and place the printed part(s) to be processed into the chamber.
Operation Modes
This product has the following operation modes:
• Preset modes - not used for PolyJet materials.
• Custom mode - used for parts printed with PolyJet printers.
To photobleach the parts:
1. Immediately after printing and cleaning, place the part(s) in ProBleacher.
2. Arrange the printed parts in the cabinet with enough distance between them to allow light to
reach all sides of each part.
3. Close the door.
4. Select Custom from the menu on the display.
Figure 1: Operation modes
Custom
mode
Stratasys ProBleacher Product Guide Operation
Page 7
© Copyright 2021 Stratasys. All rights reserved.
5. On the custom setting screen, use the up and down arrows to set the time and temperature
as follows:
• Time: from 4 hours to 12 hours each time, depending on the part size and the amount
of clear material used in the part.
• Temperature: 40°C (104°F)
Tap and hold the arrows to move quickly through the ranges.
Figure 2: Custom screen
6. When the settings are adjusted as needed, tap Run.
7. Inspect the models after 6 hours:
• For parts with a matte finish, this should be sufficient
• For parts with a glossy finish, continue photobleaching up to 24 hours to achieve the
desired results. If more time is needed, set the time and temperature again.
When photobleaching is complete, the LEDs and heat turn off automatically.
Important:
Lower temperatures may not produce satisfactory results.
Higher temperatures may cause part distortion.
To use this product without the heat feature use the down arrow until the setting
displays --.
Stratasys ProBleacher Product Guide Care and Maintenance
Page 8
© Copyright 2021 Stratasys. All rights reserved.
Run Screen
The Run screen displays the settings and status of the product.
Figure 3: Run screen
Care and Maintenance
This product is almost maintenance free, but it is recommended to keep the reflective surfaces
clean to allow sufficient light to the parts.
The preferred materials for cleaning the interior and exterior surfaces are mild detergent and
water. Follow the following guidelines:
• Before cleaning, unplug the product from the electrical outlet.
• Use a soft cloth dampened (not dripping) with soapy water.
• Do not soak the this product in water or other liquids.
• Wipe surfaces until clean, and then rinse with a clean cloth dampened with clean water.
• For resin residue, use isopropyl alcohol. If isopropyl alcohol is used, allow it to evaporate
with the door open before connecting this product to power.
• You can use general purpose household cleaners, such as 409®, Fantastik®, or Windex®
for the reflective surfaces.
• Be careful when cleaning the Lexan™ work surface inside the chamber not to allow excess
cleaning product to run over the edges where it would be impossible to wipe clean.
• When all surfaces are dry it is safe to reconnect the product to the electrical outlet.
Table 1: Run screen components
# Component # Component
1 Status of the door, lamps, and heater 4 Pauses the process until you tap Resume
2 Selected program time and temperature
settings
5 Stops the process and returns you to the
main screen
3 Process time remaining and chamber
temperature
3
12
5
4
Do not use harsh solvents like acetone, MEK, Toluene, etc. They will damage the
product. When in doubt, contact your regional service provider.
Stratasys ProBleacher Product Guide Spare Parts
Page 9
© Copyright 2021 Stratasys. All rights reserved.
Spare Parts
This product is not user-serviceable, except for the LED lamps. Replacement LED lamps are
available for purchase from your distributor or directly from our web store. Should something
break, refer to the warranty section of this guide. If your unit is not covered by the warranty,
contact your regional service provider for help.
Storage and Transportation
If it is necessary to transport or store this product, the following will ensure the safety of the
device:
1. Turn off the power switch.
2. Unplug the product from the power.
3. Wipe the inside and outside of the product with mild detergent and water or isopropyl
alcohol to remove excess resin and other debris.
4. Ensure the chamber is empty.
5. Place the product in the packing bag (optional).
6. Reinstall the protective foam end caps that originally shipped with the product onto the left
and right sides of this product.
7. Slide the bagged product with the end caps into the original boxes. Keep the product
upright.
8. Place the power cord in the open space created by the protective foam end caps.
9. Close the top of the boxes using reinforced paper tape (preferred) or clear adhesive
shipping tape (if you do not have access to reinforced paper tape). Tape all box seams.
10. Store and transport the product in the upright position.
It is not necessary to remove the LED lamps for storage or transportation.
THE 3D PRINTING SOLUTIONS COMPANY
www.stratasys.com
_____
Copyright © 2021 Stratasys Ltd. All rights reserved.
DOC-01010 Rev. C
Tabla de contenidos
Otros manuales de Impresora 3D de Stratasys
Stratasys
Stratasys Fortus 900mc Manual de instrucciones
Stratasys
Stratasys uPrint SE Instrucciones de funcionamiento
Stratasys
Stratasys Finishing Touch Manual de usuario
Stratasys
Stratasys Objet24 V2 Instrucciones de funcionamiento
Stratasys
Stratasys Dimension BST 1200 Manual de usuario
Stratasys
Stratasys Dimension Elite Manual de usuario
Stratasys
Stratasys Objet1000 Connex 2 Manual de usuario
Stratasys
Stratasys Fortus 360mc Manual de usuario
Stratasys
Stratasys F900 Manual de usuario
Stratasys
Stratasys J750 Manual de usuario
Stratasys
Stratasys Fortus 380mc Manual de instrucciones
Stratasys
Stratasys Objet30 Manual de usuario
Stratasys
Stratasys Fortus K5 Series Instrucciones de funcionamiento
Stratasys
Stratasys Fortus 450mc Manual de usuario
Stratasys
Stratasys Fortus 900mc Guía de referencia
Stratasys
Stratasys J826 Manual de usuario
Stratasys
Stratasys Objet260 Connex Manual de usuario
Stratasys
Stratasys J750 Manual de usuario
Stratasys
Stratasys Fortus 360mc Manual de usuario
Stratasys
Stratasys Connex500 Manual de usuario
