StarTech.com ST121HDWP Manual de usuario

Manual Revision: 08/14/2014

For the most up-to-date information, please visit: www.startech.com

DE: Bedienungsanleitung - de.startech.com

FR: Guide de l'utilisateur - fr.startech.com

ES: Guía del usuario - es.startech.com

IT: Guida per l'uso - it.startech.com

NL: Gebruiksaanwijzing - nl.startech.com

PT: Guia do usuário - pt.startech.com

ST121HDWP

Wall Plate HDMI® over Cat 5e/6

Extender - 165ft (50m)

*actual product may vary from photos

Instruction Manual

FCC Compliance Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications. However, there

is no guarantee that interference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by

one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols

This manual may make reference to trademarks, registered trademarks, and other

protected names and/or symbols of third-party companies not related in any way to

StarTech.com. Where they occur these references are for illustrative purposes only and do not

represent an endorsement of a product or service by StarTech.com, or an endorsement of the

product(s) to which this manual applies by the third-party company in question. Regardless

of any direct acknowledgement elsewhere in the body of this document, StarTech.com hereby

acknowledges that all trademarks, registered trademarks, service marks, and other protected

names and/or symbols contained in this manual and related documents are the property of

their respective holders.

Instruction Manual

Table of Contents

Product Diagram ....................................................................................1

Front View – Transmitter/Receiver Unit............................................................................................. 1

Rear View – Transmitter/Receiver Unit .............................................................................................. 1

Introduction............................................................................................2

Packaging Contents ................................................................................................................................. 2

System Requirements.............................................................................................................................. 2

Preparing Your Site ................................................................................2

Hardware Installation............................................................................3

EDID Conguration................................................................................4

Automatic EDID Conguration ............................................................................................................ 4

Manual EDID Conguration (EDID Copy / EDID Ghost)............................................................... 4

Restore EDID to Factory Default Settings......................................................................................... 5

LED Indicator ..........................................................................................5

Specications..........................................................................................6

Technical Support ..................................................................................7

Warranty Information............................................................................7

Instruction Manual

Transmitter Unit Receiver Unit

EDID Copy

HDMI in Port HDMI out Port

Status (Power) LED

Power Adapter Port Power Adapter Port

Link Out 1 (RJ-45

Connector) Link Out 1 (RJ-45

Connector)

Terminal

Block Power Terminal

Block Power

Link Out 2 (RJ-45

Connector) Link Out 2 (RJ-45

Connector)

Transmitter Unit Receiver Unit

Product Diagram

Front View – Transmitter/Receiver Unit

Rear View – Transmitter/Receiver Unit

Instruction Manual

Introduction

Packaging Contents

• 1 x Wall-mounted HDMI Extender

• 1 x Wall-mounted HDMI Receiver

• 1 x Universal Power Adapter (NA/UK/EU)

• 1 x Instruction Manual

System Requirements

• HDMI-enabled video source device (i.e. computer, Blu-ray player)

• HDMI-enabled display device (i.e. television, projector)

• Available AC electrical outlet or DC terminated power source for either the

transmitter or receiver

• 2x HDMI cable (for video source to transmitter and receiver to display)

Preparing Your Site

1. Determine where the local video source (i.e. computer, Blu-ray player) will

be located and set up the device. Ensure this is near an electrical box with 2x

terminated RJ45 connectors leading to the remote display.

2. Determine where the remote display will be located and place/mount the display

appropriately. Ensure this is near an electrical box with 2x terminated RJ45

connectors leading to the local video source.

Note: This HDMI extender kit features Power Over Cable, allowing both the transmitter

and receiver to be powered from a single power source that connects to either the

transmitter or receiver unit. Please ensure that the unit you’ve chosen to power

is situated near an available AC electrical outlet, or a DC terminal power source is

available in the electrical box for the transmitter or receiver unit. Make sure all devices

are turned o before beginning installation. Before you begin Hardware Installation

ensure both transmitter and receiver are properly grounded.

Instruction Manual

Hardware Installation

1. Install the RJ45 terminated Cat5e/6 Ethernet cables to the transmitter and

receiver units.

a) Connect two RJ45 terminated Cat5e/6 Ethernet cables (not included) to the

transmitter unit - one cable for the Link Out 1 RJ45 connector and another one for

the Link Out 2 RJ45 connector.

Note: Ensure that the Category 5/6 unshielded twisted pair (UTP) network cabling

between the transmitter unit and the receiver unit has been properly terminated in

a wall box in each location. Also, ensure that the patch cables are long enough to

connect the transmitter unit and the receiver unit inside their respective electrical

boxes. The cabling should not go through any networking equipment (i.e. router,

switch).

b) Connect the other ends of your terminated Cat5e/6 cable runs to the Link Out 1

and Link Out 2 RJ-45 connectors on the receiver unit.

2. Connect the power source to the transmitter or receiver unit.

Note: The HDMI extender kit only requires a single power source to be connected to

either the transmitter or receiver unit.

There are two methods for providing power to the HDMI extender kit. Please review

each method below and determine your desired method.

a) Method 1 – Using the included power adapter.

Note: If you’ve chosen Method 1 please complete step 3. (Install the extender and

receiver units into the electrical boxes) before connecting your power source.

i. Determine whether you will be connecting your power source to either the

transmitter or the receiver unit.

ii. Using the included power adapter, connect the power adapter port on either

the transmitter or receiver unit to an available wall outlet.

b) Method 2 – Using terminal DC power.

i. Determine whether you will be connecting your power source to either the

transmitter or the receiver unit.

ii. Using a small at-head screw driver, loosen the screws for the terminal block

connectors on either the transmitter or receiver unit.

iii. Connect the power and ground wires from your DC power source to the

proper terminal block connectors and refasten the screws. The proper

terminals are marked on the transmitter/receiver unit housing.

Instruction Manual

3. Install the transmitter and receiver units into the electrical boxes.

a) Install the transmitter unit into the electrical box. Please follow the instructions

included with your electrical box to determine which mounting points on the

transmitter unit should be used.

b) Install the receiver unit into the electrical box. Please follow the instructions

included with your electrical box to determine which mounting points on the

receiver unit should be used.

Note: If you have chosen to connect the power source using the included power

adapter (Method 1) please do so now.

Method 1 – Using the included power adapter.

i. Determine whether you will be connecting your power source to either the

transmitter or the receiver unit.

ii. Using the included power adapter, connect the power adapter port on either

the transmitter or receiver unit to an available wall outlet.

4. Using an HDMI cable (not included), connect your HDMI-enabled video source

device to the HDMI-in port on the transmitter unit.

5. Using an HDMI cable (not included), connect your HDMI-enabled display

device to the HDMI-out port on the receiver unit.

Your source video image will now appear on the remote video display.

EDID Conguration

Automatic EDID Conguration

Provided you have both Cat5e/6 Ethernet cables connected from the transmitter unit

to the receiver unit, the ST121HDWP will automatically relay the EDID information

provided from your HDMI display to your HDMI source device.

Manual EDID Conguration (EDID Copy / EDID Ghost)

If for any reason your conguration does not support EDID, for example there is an

adapter or a video switch used in your setup, the ST121HDWP can Copy your EDID

settings directly from your EDID compatible display.

Follow the below steps to copy the EDID settings from your display.

1. Ensure the Transmitter and Receiver units have been properly installed, including

power source.

2. Connect your HDMI display directly to the video out port on the Receiver unit.

3. Press and hold the EDID copy button the Receiver unit, until the LED lights

Green(about 3 seconds).

4. The LED will now ash Blue indicating the EDID Copy procedure was successful.

Instruction Manual

Note: If the LED ashes RED it is indicated the EDID copy procedure has failed. As

a result of one of the following:

• The display is not properly connected.

• The display is not powered on.

• The display does not support EDID.

Please check your setup and attempt the EDID Conguration procedure again.

Restore EDID to Factory Default Settings

Follow the below steps to restore the EDID settings to factory default and remove any

copied settings.

1. Ensure the Transmitter and Receiver units have been properly installed, including

power source.

2. Press the EDID Copy button on the Receiver unit, until the LED ashes RED (about 6

seconds).

3. The LED ashes Blue indicating the EDID settings have been restored to factory

default.

LED Indicator

The transmitter and receiver units on the ST121HDWP are equipped with LED

indicators to communicate.

Transmitter LED

Transmitter Status LED Indication

HDMI EDID content congured Emits blue and ashes green three times

HDCP sync in progress Emits purple

Receiver LED

Receiver Status LED Indication

Video link in progress Emits blue

No video link Emits red

NOTE: If you receive the no video link indication on your receiver unit, please

check your conguration and ensure the cabling is tested. Low-quality cables

degrade the output signal causing elevated noise levels. Use the proper cabling,

and make sure the display device supports the resolution and refresh rate that

your source device is outputting.

Instruction Manual

Specications

Local Unit Connectors 1x HDMI (19 pin) Female / 2x RJ-45 Female

Remote Unit Connectors 1x HDMI (19 pin) Female / 2x RJ-45 Female

Maximum Data Transfer Rate HDMI - 3.4Gbps

Max Distance 50 m / 165 ft

Maximum Digital Resolutions 1080p @ 60Hz, 48-bit

Wide Screen Supported Yes

Audio Specications Supports Dolby® TrueHD, DTS-HD MA

Instruction Manual

Technical Support

StarTech.com’s lifetime technical support is an integral part of our commitment to

provide industry-leading solutions. If you ever need help with your product, visit

www.startech.com/support and access our comprehensive selection of online tools,

documentation, and downloads.

For the latest drivers/software, please visit www.startech.com/downloads

Warranty Information

This product is backed by a two year warranty.

In addition, StarTech.com warrants its products against defects in materials

and workmanship for the periods noted, following the initial date of purchase.

During this period, the products may be returned for repair, or replacement with

equivalent products at our discretion. The warranty covers parts and labor costs only.

StarTech.com does not warrant its products from defects or damages arising from

misuse, abuse, alteration, or normal wear and tear.

Limitation of Liability

In no event shall the liability of StarTech.com Ltd. and StarTech.com USA LLP (or their

ocers, directors, employees or agents) for any damages (whether direct or indirect,

special, punitive, incidental, consequential, or otherwise), loss of prots, loss of business,

or any pecuniary loss, arising out of or related to the use of the product exceed the

actual price paid for the product. Some states do not allow the exclusion or limitation

of incidental or consequential damages. If such laws apply, the limitations or exclusions

contained in this statement may not apply to you.

Tabla de contenidos

Otros manuales de Extensor de StarTech.com

StarTech.com

StarTech.com USBthere USB201EXT Manual de usuario

StarTech.com

StarTech.com USB2001EXT2 Manual de usuario

StarTech.com

StarTech.com ST122UTPAGB Manual de usuario

StarTech.com

StarTech.com SV565UTPDUA Manual de usuario

StarTech.com

StarTech.com POEEXT1GAT Manual de usuario

StarTech.com

StarTech.com STUTPEALR Manual de usuario

StarTech.com

StarTech.com ST121R Manual de usuario

StarTech.com

StarTech.com USBthere USB110EXT Manual de usuario

StarTech.com

StarTech.com ST1212T Manual de usuario

StarTech.com

StarTech.com POEEXT1GAT Manual de usuario

StarTech.com

StarTech.com ST121UTPHDMI Manual de usuario

StarTech.com

StarTech.com USBthere USB204EXT Manual de usuario

StarTech.com

StarTech.com STUTPRXWLA Manual de usuario

StarTech.com

StarTech.com ST121UTP Manual de usuario

StarTech.com

StarTech.com ST121 Series Manual de usuario

StarTech.com

StarTech.com ST121WHD2 Manual de usuario

StarTech.com

StarTech.com ST12MHDLAN4K Manual de usuario

StarTech.com

StarTech.com USBthere USB100EXT Manual de usuario

StarTech.com

StarTech.com SV565UTPHDU Manual de usuario

StarTech.com

StarTech.com ST12MHDLAN Manual de usuario

StarTech.com

StarTech.com USBthere USB110EXT Manual de usuario

StarTech.com

StarTech.com ST12MHDDC Manual de usuario

StarTech.com

StarTech.com USBthere USB120EXT Manual de usuario

StarTech.com

StarTech.com ST121HD20FXA Manual de usuario

Manuales populares de Extensor de otras marcas

SY HDBT-60T Manual de usuario

Appsys ProAudio

Appsys ProAudio ADX-16 Manual de usuario

Atlona

Atlona RS232 Manual de usuario

IDK

IDK OPF-TH1000-A Manual de usuario

Enable-IT

Enable-IT 824WP Manual de usuario

Worx

Worx Landroid RadioLink WA0864 Hoja de especificaciones

TP-Link

TP-Link TL-WA730RE Manual de usuario

Camplex

Camplex CMX-HDMI-SFPL Manual de usuario

SC&T

SC&T HE03-4K Manual de usuario

Marmitek

Marmitek MegaView70 Manual de usuario

Samsung

Samsung SCS-26UC4 Manual de usuario

Foxun

Foxun SX-GES24 Manual de usuario

MuxLab

MuxLab 500771 Manual de usuario

foxunhd

foxunhd SX-AEX01 Manual de usuario

TERK Technologies

TERK Technologies LFIRX2 Manual de usuario

Devolo

Devolo Audio Extender Manual

Edimax

Edimax EW-7438RPn V2 Manual de usuario

Shinybow USA

Shinybow USA SB-6335T5 Manual de usuario