StarTech.com SAT3520U2R Manual de usuario

USB 2.0 External RAID Enclosure

SAT3520U2R Instruction Manual

Actual product may vary from photo

2 Drive USB 2.0 External RAID 0, 1 Enclosure

FCC

Compliance

Statement

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

UUssee

ooff

TTrraaddeemmaarrkkss,,

RReeggiisstteerreedd

TTrraaddeemmaarrkkss,,

aanndd

ootthheerr

PPrrootteecctteedd

NNaammeess

aanndd

SSyymmbboollss

This manual may make reference to trademarks, registered trademarks, and other protected names

and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur

these references are for illustrative purposes only and do not represent an endorsement of a product

or service by StarTech.com, or an endorsement of the product(s) to which this manual applies by the

third-party company in question. Regardless of any direct acknowledgement elsewhere in the body of

this document, StarTech.com hereby acknowledges that all trademarks, registered trademarks,

service marks, and other protected names and/or symbols contained in this manual and related

documents are the property of their respective holders.

Instruction Manual

Table

Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Hardware Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Single Mode (Non-RAID) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

RAID 0 - Spanning Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

RAID 0 - Striping Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

RAID 1 - Mirroring Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Using the RIB Clean Utility . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Drive Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Non-RAID (Single Mode) or RAID 0 Configuration . . . . . . . . . .5

RAID 1 Mirror Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Instruction Manual

Thank you for purchasing a StarTech.com 2 Drive USB 2.0 External RAID 0, 1 Enclosure.

An ideal fit for RAID applications, this Dual 3.5" SATA Drive Enclosure is the perfect

solution for consolidating your storage into a convenient, external solution.

Introduction

•Aluminum side panels maximize heat dissipation and provide durable hard drive

protection

Features

System Requirements:

•Minimum Intel Pentium III CPU 500MHz, 128MB RAM

Package contents:

•1 X Aluminum Enclosure

This package should contain:

•Internal fan helps keep the enclosure and installed hard drives running cool for

maximized performance

•Supports JBOD, Striping (RAID 0), Spanning (non RAID), and Mirror (RAID 1) modes

•Six LEDs simplify monitoring the status of enclosure and installed drives

•1 X USB Cable

•1 X Screw Driver

•1 X Power Adapter

•1 X Manual

•1 X Hard drive mounting screws

•USB 1.1/2.0 equipped PC; Win2000, WinXP, Vista

•Two 3.5” SATA 2.0 Hard Drives (for dual operation)

For PC:

•Minimum Apple G3 processor, 128MB RAM

•USB 1.1 equipped Mac; Mac OS 9.2, 10.1.5 or above

For Mac:

•USB 2.0 equipped Mac; Mac OS 10.2 or above

Instruction Manual

Hardware

Guide

Front Panel

Rear Panel

Power indicator

Rebuild indicator

HDD1 Access Indicator

HDD2 Access Indicator

HDD1 Error Indicator

HDD2 Error Indicator

Ventilation

Power switch

Power receptacle

Power indicator

USB 2.0 port

Instruction Manual

Operating

Modes

Single Mode (Non-RAID)

In Single Mode, the installed drives

will appear individually as two

independent drives. This function can

be used if only one hard drive is

installed, or two different brands or

capacities of drive are being used.

RAID 0 - Spanning Mode

In Spanning Mode, two hard drives

will appear as a single, large drive.

Spanning is an array that is written

sequentially across two drives.

RAID 0 - Striping Mode

To operate in Mirroring Mode, two

identical hard drives (capacity,

brand and model number) must be

used. In Striping Mode, two hard

drives will appear as one large, single

drive, but will provide faster data

transfers, as data will be written to the

drives in a “column” effect. This form

of array splits each piece of data

across both drives in segments. This

form of RAID does not provide

redundancy or data checking.

RAID 1 - Mirroring Mode

To operate in Mirroring Mode, two

identical hard drives (capacity,

brand and model number) must be

used. This mode creates an extra

copy (or mirrored set) of the data from

drive one on the second drive.

Mirroring Mode provides data

redundancy that is useful in the event

that the primary hard drive fails,

allowing an instant replacement of

damaged data with the second set.

Please note: If RAID 1 mode is in effect, and you wish to change to single or

RAID 0 modes, please use the RIB Clean utility to clean the drives partition

table, located on the StarTech.com website, in the Downloads section. For

more information, please see the section titled Using the RIB Clean Utility.

Instruction Manual

Using the RIB Clean Utility

If you wish to switch from RAID 1 - Mirroring Mode to another operating mode, the RIB

Clean Utility must be used to prepare partition information.

To use the RIB Clean Utility:

1. Download the utility from the StarTech.com website (Downloads section), and save it

to the local computer.

2. Double-click on the RIBClean icon to launch the Utility:

3. Once the main Utility screen loads, click on Scan Disk.

4. Once Disk Scanning is complete, click on Clean RIB. Once complete, click on Exit.

Installation

Remove the cover of the enclosure by

unfastening and removing the screws

on the bottom of the unit (bottom side

is closest to the USB 2.0 and DC/IN

ports). Insert the screwdriver into the

remaining screw hole, and press

outward.

1. Mode Selection

With the cover removed, the jumpers

used for mode selection are exposed.

Please note that the jumper pin

numbers are denoted on the circuit

board.

To configure SAT3520U2R for RAID,

use the following jumper pin

selections. Once completed, please

leave the enclosure open, for hard

drive installation:

Non-RAID

(Single Mode)

1 4

2xx5

3xx6

RAID 0

(Spanning Mode)

1x4

2xx5

3x6

RAID 0

(Striping Mode)

1x4

2xx5

3x6

RAID 1

(Mirroring Mode)

1xx4

2xx5

3 6

Instruction Manual

2. Drive Installation

Unfasten the screws on the internal

drive holder case, and pull backward

to release and remove the drive tray

from the enclosure.

Warning! If you are installing drives to be used in RAID 1 (Mirroring) Mode

with a drive that already contains data, the drives require separate installation

to prevent the data from being formatted. As such, please skip to Drive

Installation: RAID 1 (Mirror Mode). If neither of the drives contain data, you

can proceed with the following instructions (for Non-RAID or RAID 0

Configurations).

Please note that if you are configuring SAT3520U2R for RAID applications

(Mirroring Mode, Striping Mode or Spanning Mode), the installed hard

drives must be identical in brand, size and model number.

Non-RAID (Single Mode) or RAID 0 Configurations:

Insert both hard drives into the drive

tray, and secure them with screws

(provided).

Insert the drive tray (with both drives

installed) back into the enclosure.

Instruction Manual

Push the drive tray forward in the

enclosure, securing the connection.

Once the tray is firmly connected,

fasten the screws on the holder.

Replace the top panel of the

enclosure, and fasten the screws at

the bottom.

RAID 1 Mirror Mode

Insert the primary (containing data to

be mirrored) drive into the drive tray,

and fasten it to the tray with the

screws provided.

Insert the drive tray back into the

enclosure, ensuring the tray is

secured using the connectors.

Once secure, power on the enclosure.

SAT3520U2R will recognize the drive

as the master drive, and prepare it for

mirroring. Once complete, the error

light indicator of the second drive will

illuminate (denoted as HDD2 Error).

When this occurs, power off the

enclosure, and remove the drive tray

from the enclosure.

Instruction Manual

Insert the second drive (containing no

data) into the drive tray, and fasten it to

the tray with the screws provided.

Secure the drive tray to the enclosure

connections, and fasten the tray to the

enclosure using the screws removed

earlier (depicted on page 4)

Place the cover back on the

enclosure, and replace the screws

removed earlier.

Power on the enclosure.

SAT3520U2R will indicate that the

Rebuild function is under way (the

corresponding light will display

activity), as the data from Drive 1 is

mirrored onto Drive 2, and RAID 1 is

configured on the drives.

Please note that the Mirroring process

may take several minutes, depending

on the quantity of data being mirrored.

Please do NOT power off the

enclosure, until the HDD2 Error LED

is no longer illuminated.

Otros manuales para SAT3520U2R

Tabla de contenidos

Otros manuales de Recinto de StarTech.com

StarTech.com

StarTech.com 2636CABINET Manual de usuario

StarTech.com

StarTech.com S2510PESAT Manual de usuario

StarTech.com

StarTech.com 8STHSB1SATSASBA Manual de usuario

StarTech.com

StarTech.com SAT5210U2E Manual de usuario

StarTech.com

StarTech.com UNI251BMU33 Manual de usuario

StarTech.com

StarTech.com SM2NGFFMBU33 Manual de usuario

StarTech.com

StarTech.com S251BMU313 Manual de usuario

StarTech.com

StarTech.com S354UFER Manual de usuario

StarTech.com

StarTech.com S251BU31REMD Manual de usuario

StarTech.com

StarTech.com S2510BPU33 Manual de usuario

StarTech.com

StarTech.com S2510U33RUSM Manual de usuario

StarTech.com

StarTech.com IDE3510U2GB Manual de usuario

StarTech.com

StarTech.com S251BU31C3CB Manual de usuario

StarTech.com

StarTech.com S352BU33RER Manual de usuario

StarTech.com

StarTech.com RK1219WALH Manual de usuario

StarTech.com

StarTech.com UNI2510U2V Manual de usuario

StarTech.com

StarTech.com INFOSAFE SAT2510BU2 Manual de usuario

StarTech.com

StarTech.com RK616WALM Manual de usuario

StarTech.com

StarTech.com INFOSAFE IDE2510U2 Manual de usuario

StarTech.com

StarTech.com RK9WALM Manual de usuario

StarTech.com

StarTech.com S251BU31REM Manual de usuario

StarTech.com

StarTech.com S2510BMU33CB Manual del sistema

StarTech.com

StarTech.com SATSASBAY425 Manual de usuario

StarTech.com

StarTech.com SAT2510U3REM Manual del sistema

Manuales populares de Recinto de otras marcas

SilentiumPC

SilentiumPC Armis AR5 Manual

Pulsar

Pulsar 17/TRP80/DSPR Manual de usuario

Thermaltake

Thermaltake V150 TG Manual de usuario

MSI

MSI MPG SEKIRA 500X Manual de usuario

Antec

Antec Dark fleet DF-10 Manual de usuario

Nexans

Nexans WTC05 Manual de usuario

Peavey

Peavey DS 1502 Manual de usuario

D-Link

D-Link ShareCenter Pro DNS-1550-04 Manual de usuario

Rosewill

Rosewill RX82-U(JBOD) Manual de usuario

QNAP

QNAP SAS JBOD CLI 1.0 Manual de usuario

GAMDIAS

GAMDIAS Talos P1 Manual de usuario

Auvs

Auvs KR615 Manual de usuario

Digitus

Digitus DA-71114 Manual de usuario

CommScope

CommScope FDH 3000 Manual de usuario

FS FHD-FWME4 Manual de usuario

JBL

JBL CS1215T Manual de usuario

Pulsar

Pulsar ARAD-S4 Manual de usuario

Pulsar

Pulsar AWO454 Manual de usuario